BS EN 147101-1995 Specification for harmonized system of quality assessment for electronic components - Blank detail specification relay sockets of assessed quality《电子元器件质量评定协调体系规范.pdf

《BS EN 147101-1995 Specification for harmonized system of quality assessment for electronic components - Blank detail specification relay sockets of assessed quality《电子元器件质量评定协调体系规范.pdf》由会员分享，可在线阅读，更多相关《BS EN 147101-1995 Specification for harmonized system of quality assessment for electronic components - Blank detail specification relay sockets of assessed quality《电子元器件质量评定协调体系规范.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 147101:1995 Specification for Harmonized system of quality assessment for electronic components Blank detail specification Relay sockets of assessed quality The European Standard EN147101:1994 has the status of a British StandardBSEN147101:1995 BSI 04-2000 ISBN 0 580 34839 3 N

2、ational foreword This British Standard has been prepared under the direction of the Electrotechnical Sector Board, and is the English language version of EN147101:1994 Blank detail specification: Relay sockets of assessed quality, published by the European Committee for Electrotechnical Standardizat

3、ion (CENELEC) Electronic Components Committee (CECC). The text of this standard consists of the text of EN147101:1994. This standard lists the ratings, characteristics and inspection requirements which shall be included as mandatory requirements in any detail specification for this type of relay soc

4、ket. Detail specifications shall conform to the requirements of this blank detail specification and BSCECC00111: Rule of Procedure 11. Specifications Part4:1991: Regulations for CECC detail specifications. The British Standard which implements the CECC Rules of Procedure is BS9000: General requireme

5、nts for a system for electronic components of assessed quality Part2:1991 Specification for the national implementation of the CECC system. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicat

6、ion. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages 2 to 10 and a back cover. This standard has been updated (see copyright date) and

7、may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN147101:1995 BSI 04-2000 i Contents Page National foreword Inside front cover Foreword 2 1 Related documents 4 2 Characteristic

8、values 4 3 Qualification approval procedures 5 4 Quality conformance inspection 5 5 Marking 5 6 Annexes 6 7 Tests 6 8 Ordering information 6 National annex NA (informative) Committees responsible 10 National annex NB (informative) Cross references 10 Table 1 Tests for quality conformance inspection

9、7 Table 2 Tests for qualification approval 9ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 147101 January 1994 UDC Descriptors: Quality, electronic components, sockets English version Blank detail specification: Relay sockets of assessed quality Spcification particulire cadre: Supports

10、 de relais sous assurance de la qualit Vordruck fr Bauartspezifikationen: Gtebesttigte Relaisfassungen This European Standard was approved by the CENELEC Electronic Components Committee (CECC) on10August1992. CENELEC members are bound to comply with CEN/CENELEC Internal Regulations which stipulate t

11、he conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the General Secretariat of the CECC or to any CENELEC member. This European S

12、tandard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CECC General Secretariat has the same status as the official versions. CENELEC members are t

13、he national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and United Kingdom. The membership of the CECC is identical, with the exception of the national elec

14、trotechnical committees of Greece, Iceland and Luxembourg. CECC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to

15、 CENELEC members Ref. No. EN 147101:1994 EEN147101:1994 BSI 04-2000 2 Foreword The CENELEC Electronic Components Committee (CECC) is composed of those member countries of the European Committee for Electrotechnical Standardization (CENELEC) who wish to take part in a harmonized System for electronic

16、 components of assessed quality. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognized Mark, or Certificate, of Conformity. The components

17、 produced under the System are thereby acceptable in all member countries without further testing. This specification was prepared by CECC WG16 “Relays”. The text of the draft based on document CECC (Secretariat)2782 was submitted to the formal vote; together with the voting report, circulated as do

18、cument CECC(Secretariat)3142, it was approved by CECC as EN147101 on10August1992. The following dates were fixed: latest date of announcement of the ENat national level (doa) 1993-02-11 latest date of publication of an identical national standard (dop) 1993-08-11 latest date of declaration of nation

19、al standards obsolescence 1993-08-11 latest date of withdrawal of conflicting national standards (dow) 2003-02-11EN147101:1994 BSI 04-2000 3 (1) CECC 147101-xxx Issue: . Pages 1 to. (2) Electronic components of assessed quality in accordance with EN 147000:1993 EN 147100:1993 (3) (4) Detail specific

20、ation for relay sockets of assessed quality Type: (5) Construction: (6) (Outline drawing) (7) Application: (8) Test schedule: Characteristics: (9) (10) Information about manufacturers who have components qualified to this detail specification is available in the current CECC 00200 (Register of Appro

21、vals).EN147101:1994 4 BSI 04-2000 Key for page3 The first page of the detail specification should have the layout recommended on page3. The numbers between brackets on page3 correspond to the following indications which should be given: Identification of the detail specification (1) The name of the

22、National Standardization Organization under whose authority the detail specification is published and, if applicable, the organization from whom the detail specification is available. (2) The CECC-symbol and the number allocated to the completed detail specification by the CECC General Secretariat.

23、(3) The number and year of availability of the EN generic specification and/or sectional specification, also national reference, if different. (4) If different from the CECC number, the national number of the detail specification, date of issue and any further informations required by the national s

24、ystem, together with any amendment numbers. Identification of the socket (5) Type: type(s) of contacts, fixed or removable, number and arrangement, contact current and voltage. (6) Construction: e.g.water proof or not, nature of available wiring (wire size), other characteristics. (7) Basic outline

25、drawing and cut out; the detailed variants for terminals and mountings shall be given in annexes, if necessary. (8) Application and test schedule. (9) Summary of most important characteristics allowing comparison between different variants which may be used for a given or similar application. (10) C

26、omponent climatic category and temperature range. NOTEContents of (5) and (6) shall be suitable for an entry in CECC00200. 1 Related documents EN 147000:1993, Generic specification: Relay sockets of assessed quality. EN 147100:1993, Sectional specification: Relay sockets of assessed quality. CECC 00

27、114/II (1992), Quality assessment procedures. PartII: Qualification approval of electronic components. National authorized institutions will complete this section making reference to any documents or specifications directly referred to in their national equivalent of this document. 2 Characteristic

28、values 2.1 General characteristics Construction:. Operating temperature range:. C Storage temperature range:. C Climatic category:. Type and number of contacts: . Mass:.g Finish of the terminals:.EN147101:1994 BSI 04-2000 5 2.2 Construction of designation (ordering information) 2.3 Electrical charac

29、teristics 2.4 Mechanical characteristics Shock: acceleration, duration Vibration: sinusoidal and/or random, acceleration and frequency range Bump: acceleration, number of bumps Mounting torque:.Nm Insertion and withdrawal force/number of insertions:. N/. Contact retention into insulator body:. N 3 Q

30、ualification approval procedures In accordance with CECC00114/II 1.4method1 (fixed sampling). Sampling and test schedule are described inTable 2. The tests specified and their order are mandatory. Additional samples are prescribed in some sampling groups to allow replacement of defective samples in

31、the sampling groups. After the use of these sockets, no complementary replacement is allowed. 4 Quality conformance inspection Quality conformance inspection contains the tests stated inTable 1: Group A and B tests for inspection lot acceptance. Group C periodic tests. Unless otherwise stated in thi

32、s specification, all tests ofTable 1 are mandatory. Where a sub-group contains cumulative tests, the order of the tests is mandatory. Specimens subjected to tests denoted as destructive (D) shall not be released for delivery. 4.1 Formation of inspection lots According to CECC00114/II clause3.1. 4.2

33、Interval between group C tests One year. 5 Marking According to EN147100:1993 clause5. Contact current: .A max. Contact resistance: initial.m7 max. after test.m7 max. Insulation resistance: initial.M7 min. after climatic sequence.M7 min. Dielectric withstand voltage: at nominal pressure.V min. at lo

34、w atmospheric pressure.V min.EN147101:1994 6 BSI 04-2000 6 Annexes Annexes may be added, for example: 7 Tests 7.1 Standard conditions for testing All tests shall be performed according to conditions stated in EN147000:1993 clause5.5. 7.2 Mounting of test items The following requirements shall apply

35、for mechanical tests e.g.shock, vibration, bump: The socket shall be mounted by its normal mounting methods to the test fixture. The test fixture shall be sufficiently rigid to minimize inherent resonances so as not to invalidate the test. 7.3 Wiring of test specimens The detail specifications shall

36、 define the wiring method, as well as type and size of wire. 8 Ordering information See clause2.2. Annex 1 for polarizing or keying Annex 2 for type of contacts Annex 3 for mounting variantsEN147101:1994 BSI 04-2000 7 Table 1 Tests for quality conformance inspection Test Group A Sub-group A1 Test No

37、. Test Test conditions according to sub-clauses of EN 147000:1993 IL AQL Performance 1 Visual inspection 5.6.4 items 2 to 4 S3 1,5% Satisfactory aspect of insulator body fixtures and finish 2 Marking 5.6.4 item 1 Marking as specified in clause5 3 Mounting and fixture 5.9 S3 1.5% Tolerances as specif

38、ied in annex . 4 Insertion and withdrawal force 5.8 As specified in detail specification 5 Contact retention into insulator body 5.11 As specified in detail specification 6 Retention force of the socket contact 5.10 As specified in detail specification 7 Dielectric strength test 5.14 Application poi

39、nts: all terminals defined in 5.14.2 No breakdown or flashover, maximum leakage current1mA/100 4s 8 Insulation resistance test 5.15 As specified in detail specification Sub-group A2 9 Weighing 5.7 S4 1% As specified in detail specification 10 Dimensions 5.6.1 As specified in detail specification Tes

40、t Group B Sub-group B1 11 Wiring of crimping contacts (D) 5.13 S3 1,5% Limit of breaking force 12 Soldering 5.23 See 5.23 13 Replacement of removable contacts (D) 5.12 Test No. 1 and No. 5 14 Contact circuit resistance 5.16 As specified in detail specificationEN147101:1994 8 BSI 04-2000 Table 1 Test

41、s for quality conformance inspection Test Group C Sub-group C1 12 months Test No. Test Test conditions according to sub-clauses of EN 147000:1993 No of samples Allowed defectives Performance 15 Mechanical endurance (D) 5.28 Number of insertions/extractions 4 1 Tests No. 1, 4, 6 and13 Sub-group C2 12

42、 months 16 Climatic sequence 5.20 Upper reference temp. included in sequence 1 5.20.2 Dry heat: 125 C, 16 h Test No. 13 5.20.3 Damp heat, cyclic: first cycle 5.20.4 Low air pressure: Test No. 7 see 6.3.3 2 Test voltage: see 6.3.3 5.20.5 Damp heat, cyclic: remaining cycles 5.20.7 Final measurements T

43、ests No. 1, 4, 5 and 6 17 Salt spray (D) 5.22 Severity 24 h 2 Test No. 1 18 Shock 5.17 Method 1, 3 shocks 2 19 Vibration (D) 5.19 Frequency range and acceleration according to6.3.4 6 cycles in each axis 2 No opening of circuit greater than 10 4s 20 Bump 5.18 Acceleration according to 6.3.4 method 1

44、2 Final measurements Tests No. 1, 4, 5 and 6 Sub-group C3 24 months 21 Resistance to cleaning solvents 5.24 2 0EN147101:1994 BSI 04-2000 9 Table 2 Tests for qualification approval Sample size: 20 + 3 Variants of samples: Test group1 shall apply to all possible variants Group 0 = all samples Test Tes

45、t conditions and requirements according to Table 1 No. of samples Allowed defective s Test as per EN 147000 Test sequence Test No. Sub-group Visual inspection 5.6.4 1 A1 all Marking 5.6.4 2 A1 all Weighing 5.7 9 A2 5 Dimensions 5.6.1 10 A2 5 Mounting and fixture 5.9 3 A1 5 Retention force of the soc

46、ket contact 5.10 6 A1 all 0 Contact retention into insulator body 5.11 1 5 A1 all Insertion and withdrawal force 5.8 4 A1 all Dielectric strength test 5.14 7 A1 all Insulation resistance test 5.15 8 A1 all Contact circuit resistance 5.16 14 B1 all Group 1 = 6 + 1 samples Replacement of removable con

47、tacts (D) 5.12 1-5 13 B1 3 Wiring of crimping contacts (D) 5.13 11 B1 3 Soldering 5.23 12 B1 3 Shock 5.17 18 C2 3 1 Bump 5.18 1-4-5 20 C2 3 Vibration (D) 5.19 1-4-5 19 C2 3 Group 2 = 8 + 1 samples Climatic sequence 5.20 1-8-14 16 C2 2 Salt spray (D) 5.22 1-8 17 C2 2 Resistance to clearing solvents 5

48、.24 1-10-4-13-8 21 C3 2 1 Fluid contamination 5.25 1-10-4-13-7-8 2 Group 3 = 6 + 1 samples Rapid change of temperature 5.21 1-14 2 Flammability test (D) 5.26 1 Thermal endurance 5.27 8-14 1 1 Mechanical endurance (D) 5.28 1-6-4-14 15 C1 2BSEN147101:1995 10 BSI 04-2000 National annex NA (informative)

49、 Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted to Technical Committee EPL/94, General Purpose Relays and Reed Contact Units, upon which the following bodies were represented: Federation of Electronic Industries Ministry of Defence National Supervising Inspectorate (BSI QA) National annex NB (informative) Cross-references Publication referred to Corresponding British Standard EN 147000:1993 BS EN 1470