BS EN 13702-2010 Bitumen and bituminous binders Determination of dynamic viscosity of modified bitumen by cone and plate method《沥青和沥青结合料 圆锥体和平板法测定改性沥青的动态粘滞度 n》.pdf

《BS EN 13702-2010 Bitumen and bituminous binders Determination of dynamic viscosity of modified bitumen by cone and plate method《沥青和沥青结合料 圆锥体和平板法测定改性沥青的动态粘滞度 n》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13702-2010 Bitumen and bituminous binders Determination of dynamic viscosity of modified bitumen by cone and plate method《沥青和沥青结合料 圆锥体和平板法测定改性沥青的动态粘滞度 n》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 13702:2010BS 2000-513:2010Bitumen and bituminous binders Determination of dynamic viscosity of modified bitumen by cone and plate methodLicensed Copy: Wang Bin, ISO/EXCHANG

2、E CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13702:2010. Itsupersedes BS EN 13702-1:2003 which is withdrawn. The UK participation in its preparation was entrusted to TechnicalComm

3、ittee PTI/13, Petroleum Testing and Terminology.A list of organizations represented on this committee can beobtained on request to its secretary.Energy Institute, under the brand of IP, publishes and sells all Parts of BS 2000, and all BS EN petroleum test methods that would be Part of BS 2000, both

4、 in its annual publication “Standard methods for analysis and testing of petroleum and related products and British Standard 2000 Parts” and individually.Further information is available from: Energy Institute, 61 New Cavendish Street, London W1G 7AR. Tel: 020 7467 7100. Fax: 020 7255 1472.This publ

5、ication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010 ISBN 978 0 580 64339 2 ICS 75.140; 91.100.50 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published u

6、nder the authority of theStandards Policy and Strategy Committee on 31 October 2010. Amendments issued since publicationDate Text affected Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE N

7、ORM EN 13702 May 2010 ICS 75.140; 91.100.50 Supersedes EN 13702-1:2003English Version Bitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen by cone and plate method Bitumes et liants bitumineux - Dtermination de la viscosit dynamique des bitumes modifis - Mthode cne

8、 et plateau Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskositt von modifiziertem Bitumen - Platte-Kegel-Verfahren This European Standard was approved by CEN on 23 April 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the cond

9、itions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in thr

10、ee official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of

11、Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

12、EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13702:2010: ELicensed Co

13、py: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010EN 13702:2010 (E) 2 Contents page Foreword 31 Scope 42 Normative references 43 Principle 44 Apparatus . 55 Sampling . 56 Procedure . 57 Expression of results 68 Precision . 68.1 Repeatability . 68

14、.2 Reproducibility . 69 Test report 6Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010EN 13702:2010 (E) 3 Foreword This document (EN 13702:2010) has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”, the secretariat

15、 of which is held by AFNOR/BNP. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is dr

16、awn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13702-1:2003. This document was formerly known as EN 13702 Part 1. As Par

17、t 2 of this standard was merged with another standard into EN 13302, this standard was renumbered into EN 13702. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgari

18、a, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang B

19、in, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010EN 13702:2010 (E) 4 1 Scope This European Standard specifies a method for determining the dynamic viscosity of a modified bituminous binder over a range of temperatures by means of a cone and plate viscomet

20、er. Although the method has been developed for modified binders, it is also suitable for other bituminous binders. NOTE Unlike penetration grade bitumen, polymer modified bitumens (PMBs) may not show a straight line on the Heukelom-Diagram. This implies that in order to obtain information about the

21、temperature susceptibility of PMBs, viscosity should be measured at different temperatures. WARNING The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It i

22、s the responsibility of the user of this European Standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 2 Normative references The following referenced documents are indispensable for the application of this document. Fo

23、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 58, Bitumen and bituminous binders Sampling bituminous binders EN 12594, Bitumen and bituminous binders Preparation of test samples 3 Princ

24、iple The sample is placed on a plate, a cone is pressed onto the sample and the system is brought to the test temperature. A stress is applied to the sample by rotation. The torque is measured from the applied shear rate and dynamic viscosity is calculated by: =(1) where is the shear rate expressed

25、in s-1; is the stress expressed in Pa, calculated by: dMA= (2) where A is the cone factor expressed in m-3; Mdis the torque in expressed N m. NOTE The advantages of this method are the use of a very small sample and the speed of the method, especially regarding thermal conditioning of the specimen.

26、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBS EN 13702:2010EN 13702:2010 (E) 5 4 Apparatus Cone and plate viscometer, with the following minimum capabilities: range of shear rate: 5 x 10-2s-1to 5 x 102s-1; range of viscosity: 5 x 10-2Pa s to 10

27、5Pa s; range of temperature: 60 C to 150 C. The sample temperature shall be maintained within 0,5 C up to 100 C and within 1,0 C above 100 C. 5 Sampling Take the sample in accordance with EN 58 and prepare the sample in accordance with EN 12594. 6 Procedure Select the appropriate size (diameter and

28、angle) of cone to allow measurement at the selected shear rate. Place the sample on the plate and press the selected cone onto the sample. Remove any surplus sample and bring the system to the test temperature. Commence the first measurement at the lowest temperature: Temperature: (60 0,5) C; Shear

29、rate: 5 x 10-2s-1. Check the reading after a delay of 15 min when reaching the temperature and note the temperature, the cone size, the shear rate and the reading. Repeat the test and calculate the result as an average of two tests. Replace the specimen and increase the temperature to the next test

30、temperature. Commence the second measurement: Temperature: (100 0,5) C; Shear rate: 5 x 101s-1. Replace the specimen and increase the temperature to the next test temperature. Commence the third measurement: Temperature: (150 1,0) C; Shear rate: 5 x 102s-1. It should be ensured that the complete spe

31、cimen has reached the test temperature before starting the test. The sample should not contain any filler. NOTE In addition to these test temperatures and shear rates any other temperature and shear rate can be used. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontroll

32、ed Copy, (c) BSIBS EN 13702:2010 EN 13702:2010 (E) 6 7 Expression of results Record the results of the measurement of dynamic viscosity with the corresponding shear rate and the test temperature. Express the viscosity values in Pa s as follows: (1,000 x 10x) Pa s. 8 Precision NOTE The following prec

33、ision data are the best currently estimated and are proposed until results of further round robin tests are available. 8.1 Repeatability The difference between two successive results, obtained by the same operator with the same apparatus under constant operating conditions on identical test material

34、 would, in the long run, in the normal and correct operation of the test method, differ by more than 5 % in only one case in twenty. 8.2 Reproducibility The difference between two single and independent results, obtained by different operators working in different laboratories on identical test mate

35、rial would, in the long run, in the normal and correct operation of the test method, differ by more than 15 % in only one case in twenty. 9 Test report The test report shall contain at least the following information: a) type and complete identification of the sample under test; b) reference to this

36、 European Standard; c) temperature, shear rate and the result of the test (see Clause 7); d) diameter and angle of the cone; e) date of the test; f) any deviation, by agreement or otherwise, from the specified procedure. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncont

37、rolled Copy, (c) BSIThis page deliberately left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIEnergy InstituteBuying Parts of BS 2000Orders for BS 2000 publications should be addressed to either:Energy Institute Library and Information Servic

38、e61 New Cavendish StreetLondonW1G 7ARTel: +44 (0)20 7467 7100Fax: +44 (0)20 7255 1472www.energyinst.org.ukOrder standards securely via:www.energyinstpubs.org.ukor:British Standards Institution Customer Services389 Chiswick High RoadLondonW4 4ALTel: +44 (0)20 8996 9001Fax: +44 (0)20 8996 Order hard c

39、opy standards securely via: exists in all BS 2000 publications. No part of this publication may be reproduced in any form without the prior permission in writing of BSI and the Energy Institute. Enquiries about copyright should be made to the Secretary of PTI/13 at the Energy Institute.PTI/13BS 2000

40、 SeriesLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIThis page deliberately left blankLicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 12/01/2011 06:50, Uncontrolled Copy, (c) BSIBSI is the independent national body responsible for preparing

41、 British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick Hi

42、gh Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We w

43、ould be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an indivi

44、dual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the webs

45、ite addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have b

46、een publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information serv

47、ices are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and oth

48、er benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyrigh