BS EN 12971-2-1999 Reinforcements - Specification for textile glass chopped strands - Test methods and general requirements《增强材料 纺织玻璃短切原丝的规范 试验方法和一般要求》.pdf

《BS EN 12971-2-1999 Reinforcements - Specification for textile glass chopped strands - Test methods and general requirements《增强材料 纺织玻璃短切原丝的规范 试验方法和一般要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 12971-2-1999 Reinforcements - Specification for textile glass chopped strands - Test methods and general requirements《增强材料 纺织玻璃短切原丝的规范 试验方法和一般要求》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12971-2:1999 The Eu

2、ropean Standard EN 12971-2:1999 has the status of a British Standard ICS 59.100.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Reinforcements Specification for textile glass chopped strands Part 2: Test methods and general requirementsThis British Standard, having been pre

3、pared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 September 1999 BSI 09-1999 ISBN 0 580 32884 8 BS EN 12971-2:1999 Amendments issued since publication Amd. No. Date Comments National

4、 foreword This British Standard is the English language version of EN 12971-2:1999. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; presen

5、t to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on re

6、quest to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of

7、 the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations.

8、Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 and 3 and a back cover. The BSI copyright notice displayed throughout this document indicates when the document was last issued.CEN European Committee for Standardization Comite Europe en de Nor

9、malisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12971-2:1999 E EUROPEAN STANDARD EN 12971-2 NORME EUROPE ENNE EUROPA ISCHE

10、NORM May 1999 ICS 59.100.10 English version Reinforcements Specification for textile glass chopped strands Part 2: Test methods and general requirements Renforts Spe cification de fils de verre coupe s Partie 2: Me thodes dessais et exigences ge ne rales Versta rkungen Spezifikation fu r geschnitten

11、e Textilglasgarne Teil 2: Pru fverfahren und allgemeine Anforderungen This European Standard was approved by CEN on 16 April 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stand

12、ard wihtout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official version (English, French, German). A version in any other lan

13、guage made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,

14、 Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom .Page 2 EN 12971-2:1999 BSI 09-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 249, Plastics, the Secretariat of which is held by IBN. This European

15、 Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1999, and conflicting national standards shall be withdrawn at the latest by November 1999. According to the CEN/CENELEC Internal Regulations, the natio

16、nal standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Th

17、is standard is one part of EN 12971 which is structured as follows: Textile glass Chopped strands Part 1: Designation; Textile glass Chopped strands Part 2: Test methods and general requirements; Textile glass Chopped strands Part 3: Technical specification. Contents Page Foreword 2 1 Scope 3 2 Norm

18、ative references 3 3 Definitions 3 4 List of properties 3 5 Sampling 3 6 General requirements 3 6.1 Appearance 3 6.2 Packaging 3 6.3 Labelling 3Page 3 EN 12971-2:1999 BSI 09-1999 Table 1 List of physical properties Properties Test method Remarks Combustible matter content ISO 1887 Moisture content E

19、N ISO 3344 Average fibre length No method Defined by manufacturer Filament diameter ISO 1888 For designation only Glass type No method For designation only Bulk density ISO/CD 15100 1 Scope 1.1 This part 2 of EN 12971 defines the test methods to be used to determine the designated and specified prop

20、erties given in part 1 and 3 respectively. 1.2 This part 2 of EN 12971 defines the general requirements applicable to the specification of all types of chopped strand falling within the scope of this specification as defined in part 1 of the standard. 2 Normative references This European Standard in

21、corporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this E

22、uropean Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN ISO 1886, Reinforcement fibres Sampling plans applicable to received batches. (ISO 1886:1990) EN ISO 3344, Reinforcement products Determination

23、 of moisture content. (ISO 3344:1997) ISO 472, Plastics Vocabulary. ISO 1887, Textile glass Determination of combustible-matter content. ISO 1888, Textile glass Staple fibres or filaments Determination of average diameter. ISO/CD 15100, Reinforcement fibres Chopped strands Determination of bulk dens

24、ity. 3 Definitions For the purposes of this part 2 of EN 12971 the definitions given in ISO 472 apply with the following additions: 3.1 lot average an average property of a lot (in manufacture or delivered to the customer), when sampled in accordance with EN ISO 1886 3.2 bulk density the mass of a d

25、efined volume of chopped strands put into a container, without compression or the effects of settlement 3.3 moisture loss in storage for wet chopped strands, the difference between the original moisture content and that measured after a period in storage 4 List of properties The list of properties w

26、ith the applicable test method shall be considered as a guide for the selection of the properties and limits which shall be applicable to the technical specifications given in part 3 of this standard. 5 Sampling Sampling of textile glass chopped strands for the purpose of confirming conformance with

27、 the requirements of this specification shall be undertaken in accordance with EN ISO 1886. 6 General requirements 6.1 Appearance The textile glass chopped strands shall be substantially free from contamination (e.g. oil, metals, paper, etc.), and shall not contain unacceptable levels of agglomerate

28、d filament (fuzz ball). If required the purchase specification shall define acceptance levels. 6.2 Packaging The packaging shall protect the product during handling, storage and transportation and ensure that the material has a minimum shelf life of 12 months. For wet chopped strands, the packaging

29、shall include a moisture-proof package so as to keep control of moisture loss to ensure a minimum shelf life of 6 months. 6.3 Labelling Each package shall be clearly identified with: 6.3.1 Designation code. 6.3.2 Manufacturers production and traceability reference. 6.3.3 Weight of package (net). 6.3

30、.4 Any special handling/storage instructions.BS EN 12971-2:1999 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

31、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions

32、 British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigui

33、ty while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers a

34、utomatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply

35、 the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI

36、 electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchas

37、e price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Exc

38、ept as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in

39、 the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.