BS EN 1744-5-2006 Tests for chemical properties of aggregates - Determination of acid soluble chloride salts《集料的化学特性试验 酸溶性氯化物盐的测定》.pdf

《BS EN 1744-5-2006 Tests for chemical properties of aggregates - Determination of acid soluble chloride salts《集料的化学特性试验 酸溶性氯化物盐的测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN 1744-5-2006 Tests for chemical properties of aggregates - Determination of acid soluble chloride salts《集料的化学特性试验 酸溶性氯化物盐的测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58

2、Part 5: Determination of acid soluble chloride saltsThe European Standard EN 1744-5:2006 has the status of a British StandardICS 91.100.15Tests for chemical properties of aggregates BRITISH STANDARDBS EN 1744-5:2006BS EN 1744-5:2006Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 0

3、2:12, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 September 2007 BSI 2007ISBN 978 0 580 53746 2Amendments issued since publicationAmd. No. Date CommentsCompliance with a British Standard cannot confer immunity

4、 from legal obligations.National forewordThis British Standard is the UK implementation of EN 1744-5:2006.The UK participation in its preparation was entrusted by Technical Committee B/502, Aggregates, to Subcommittee B/502/6, Test methods.A list of organizations represented on this committee can be

5、 obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1744-5October 2006ICS 91.100.15English VersionTests for chemical properti

6、es of aggregates - Part 5:Determination of acid soluble chloride saltsEssais pour dterminer les proprits chimiques desgranulats - Partie 5: Dtermination de la teneur enchlorures solubles dans lacidePrfverfahren fr chemische Eigenschaften vonGesteinkrnungen - Teil 5: Bestimmung der surelslichenChlori

7、deThis European Standard was approved by CEN on 28 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical refe

8、rences concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into

9、 its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Lux

10、embourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All right

11、s of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1744-5:2006: ELicensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 2 Contents page Foreword. 3 1 Scope 4 2 Normative references . 4

12、3 Definitions 4 4 Reagents 4 4.1 General requirements for densities 5 4.2 Reagents for determination of acid -soluble chloride salts (Volhard method) 5 5 Apparatus 6 6 Principle . 6 7 Sampling 6 8 Preparation of test portion. 6 9 Procedure 7 10 Calculation and expression of results 7 11 Test report

13、. 7 Bibliography . 8 Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 3 Foreword This document (EN 1744-5:2006) has been prepared by Technical Committee CEN/TC 154, “Aggregates“, the secretariat of which is held by BSI. This Europ

14、ean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national standards shall be withdrawn at the latest by April 2007. This standard forms part of a series of tests for chemical prop

15、erties of aggregates. Test methods for other properties of aggregates will be covered by Parts of the following European Standards: EN 932 Tests for general properties of aggregates EN 933 Tests for geometrical properties of aggregates EN 1097 Tests for mechanical and physical properties of aggregat

16、es EN 1367 Tests for thermal and weathering properties of aggregates EN 13179 Tests for filler aggregate used in bituminous mixtures The other parts of EN 1744 are, or will be: Part 1: Chemical analysis Part 2: Determination of resistance to alkali reaction Part 3: Preparation of eluates by leaching

17、 of aggregates Part 4: Determination of water susceptibility of fillers for bituminous mixtures Part 6: Determination of the influence of recycled aggregate extract on the initial setting time of cement According to the CEN/CENELEC Internal Regulations, the national standards organizations of the fo

18、llowing countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, S

19、pain, Sweden, Switzerland and United Kingdom. Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 4 1 Scope This European Standard specifies the procedure for the determination of acid soluble chloride salts which may be present in a

20、ggregates. This test is suitable for aggregates where the chloride content does not derive directly from contact with, or immersion in, saline water. Examples of such aggregates are: recycled aggregates containing hydrated cement, where chloride may be bound as calcium chloroaluminates; and some agg

21、regates from desert areas where chloride is occluded within the aggregate particles. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edi

22、tion of the referenced document (including any amendments) applies. EN 1744-1:1998, Tests for chemical properties of aggregates Part 1: Chemical analysis EN 932-1, Tests for general properties of aggregates Part 1: Methods for sampling EN 932-5, Tests for general properties of aggregates Part 5: Com

23、mon equipment and calibration ISO 384, Laboratory glassware Principles of design and construction of volumetric glassware ISO 1042:1983, Laboratory glassware One-mark volumetric flasks 3 Definitions For the purposes of this standard, the following terms and definitions apply. 3.1 test portion sample

24、 used as a whole in a single test 3.2 test specimen when a test method requires more than one determination of a property, the test specimen is the sample used in a single determination 3.3 laboratory sample reduced sample derived from a bulk sample for laboratory testing 4 Reagents Unless otherwise

25、 stated, use only analytical grade reagents and demineralised water, or water of equivalent purity. NOTE 1 Unless otherwise stated “%“ means “% by mass“. NOTE 2 Where no tolerances are given for reagent volumes or masses, the values quoted are approximate. In such cases volumes delivered from measur

26、ing cylinders and indicated masses using the ordinary balance specified in 5.1 are considered sufficiently accurate for the purposes of this European Standard. NOTE 3 Unless otherwise stated reagent solutions may be assumed to have long-term stability. Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA ST

27、ANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 5 NOTE 4 All chemicals should be treated as potential poisons with toxic properties and appropriate precautions taken before their use. Always take time to assess possible hazards before starting any procedures and constant atte

28、ntion should be maintained. 4.1 General requirements for densities The following concentrated liquid reagents required by this standard shall have the following densities in grams per cubic centimetre at (20 3) C. Hydrochloric acid : 1,18 to 1,19 Nitric acid : 1,40 to 1,42Sulfuric acid : 1,84 Ammoni

29、um hydroxide : 0,88 to 0,91 The degree of dilution shall be indicated as a volumetric sum. NOTE Ready for use solutions are allowed as an alternative. 4.2 Reagents for determination of acid -soluble chloride salts (Volhard method) 4.2.1 Silver nitrate (AgNO3) solution: 0,100 mol/l is prepared by dry

30、ing about 20 g of silver nitrate for at least 1 h at a temperature of (110 5) C, allowing it to cool in a dessicator, weighing (16,987 0,001) g of the dried silver nitrate, then dissolving it in water and diluting it to 1 l in a volumetric flask (5.6). Store the solution in the amber-coloured glass

31、reagent bottle (5.7) and protect from prolonged exposure to sunlight. 4.2.2 Thiocyanate (KSCN or NH4SCN) solution: approximately 0,1 mol/l is prepared by dissolving 9,7 g of potassium thiocyanate or 7,6 g of ammonium thiocyanate in water and diluting it to 1 l in a volumetric flask. Pipette 25 ml of

32、 silver nitrate solution (4.2.1) into a flask (5.8) and add 5 ml of nitric acid (4.2.3) and 1 ml of ammonium iron (III) sulfate indicator solution (4.2.5). Add the thiocyanate solution from a burette (5.9) until the first permanent colour change occurs, that is from white opalescence to pale brown.

33、Note the volume of thiocyanate solution (V0) added. Calculate the concentration of the thiocyanate solution cT, (in moles per litre), from the following equation: cT= 2,5/V0 (1) where V0is the volume of thiocyanate added (in millilitres). Standardize the solution at weekly intervals or before use if

34、 the tests are carried out infrequently. 4.2.3 Nitric acid (HNO3): approximately 6 mol/l is prepared by adding 100 ml of nitric acid (4.1) to 150 ml of water, boiling the diluted acid in a fume cupboard (5.11) until it is colourless and allowing to cool to room temperature. 4.2.4 Chloride free techn

35、ical grade 3,5,5,-trimethylhexan-1-ol. 4.2.5 Ammonium iron (III) sulfate NH4Fe(SO4)2.12H2O indicator solution is prepared by adding 60 g of water to 50 g of ammonium iron (III) sulfate, warming until it dissolves, and adding 10 ml of nitric acid (4.2.3). Allow the solution to cool to room temperatur

36、e and store it in a glass bottle (5.10). Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 6 5 Apparatus All apparatus shall comply with the general requirements of EN 932-5. All volumetric glassware shall be of class B accuracy as

37、 defined in ISO 384. Volumetric glassware of class A shall be used for audit test and type test. 5.1 Balance, capable of weighing up to 100 g, readable to the nearest 0,1 mg. 5.2 Two filter funnels, of approximately 100 mm diameter with coarse filter papers (pore diameter approximately 20 m); of dia

38、meters appropriate to the size of the funnels. 5.3 Two 250 ml beakers. 5.4 Glass rods. 5.5 Pipette: 1 ml, 5 ml, 25 ml 5.6 Two volumetric flasks, capacity of 1 l, complying with the requirements of ISO 1042. 5.7 Amber-coloured glass reagent bottles. 5.8 Stoppered conical flasks, 100 ml and 250 ml cap

39、acity. 5.9 Burette, 50 ml size, graduated to 0,1 ml. 5.10 Plain glass reagent bottles. 5.11 Fume cupboard. 6 Principle This method gives the total halide content except for fluoride and expresses the result as chloride ion content. The aggregate sample is reduced to a fine powder and extracted with

40、boiling dilute nitric acid. NOTE Sulfides are oxidised into sulfates and do not interfere. The dissolved chloride is precipitated using a known volume of standard silver nitrate solution. After boiling, the precipitate and the remaining solid aggregate are washed with a dilute nitric acid and discar

41、ded. The filtrate and washings are cooled to room temperature and the residual silver nitrate is titrated with a standard thiocyanate solution using an iron (III) salt as an indicator (Volhard method). 7 Sampling The laboratory sample shall be taken in accordance with the procedures specified in EN

42、932-1. Ensure that the laboratory sample is representative of the moisture content as well as the solids. 8 Preparation of test portion The test specimen is prepared using the procedure given in EN 1744-1:1998, 12.3. Take approximately 2 g of the powdered sample as the test specimen. Licensed Copy:

43、Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 7 9 Procedure Weigh the test specimen to the nearest 0,1 mg and record it as “m”; place it in a 250 ml beaker, add 50 ml of water and while stirring with a glass rod, 50 ml of dilute nitric acid (

44、1 + 2). Heat the mixture to boiling, stirring occasionally, and boil for 1 min. NOTE Aggregates containing significant amounts of carbonates will froth on addition of the acid. In these cases, add the acid slowly while continuously stirring. Add 5 ml of the 0,100 mol/l silver nitrate solution by pip

45、ette (5.5) into the boiling solution. Then boil for a maximum of 1 min and filter through a filter paper (5.2) washed before use with dilute nitric acid (1 + 100) into a 500 ml flask (5.6). Wash the beaker, glass rod and filter with dilute nitric acid (1 + 100) until the volume of filtrate and washi

46、ngs is 200 ml. Cool the filtrate and washings to room temperature. Add 5 ml ammonium iron (III) sulfate indicator solution and titrate with the thiocyanate solution, shaking vigorously until a drop of this solution produces a faint brown coloration which no longer disappears on shaking. Note the vol

47、ume V1of the thiocyanate solution added. If the chloride content of the aggregate exceeds 0,85 %, it will be necessary to start the test again with a smaller test portion. Repeat the procedure with a second test specimen. 10 Calculation and expression of results Calculate the chloride content (in %)

48、 from the following equation: Ca =3,545 x (5-10 CT V1)/1000 x 100/m = 0,3545(5-10 CT V1)/m (2) where: m is the mass of the test portion (in grams); V1 is the volume of thiocyanate solution used for the titration of the test solution (in millilitres); CTis the concentration of the thiocyanate solutio

49、n (in moles/litre, see 4.2.2). The result of the test is given as the mean of the determinations on the two test specimens, and recorded to the nearest 0,01 %. 11 Test report a) reference to this European Standard; b) source of the sample; c) designation of the sample; d) mass of dry sample tested, (in grams); e) result of the test; f) date of the test. Licensed Copy: Hong Ling, ISO/EXCHANGE CHINA STANDARDS, 30/11/2007 02:12, Uncontrolled Copy, (c) BSIEN 1744-5:2006 (E) 8 Bibliography 1 EN 196-21:1989, Methods of testing cement: Determinatio