BS AU 28-1964 Specification for towing jaw for use between trailers of 5-35 tons gross weight and towing vehicle《总重5-35吨的挂车和牵引车的牵引爪规范》.pdf

《BS AU 28-1964 Specification for towing jaw for use between trailers of 5-35 tons gross weight and towing vehicle《总重5-35吨的挂车和牵引车的牵引爪规范》.pdf》由会员分享，可在线阅读，更多相关《BS AU 28-1964 Specification for towing jaw for use between trailers of 5-35 tons gross weight and towing vehicle《总重5-35吨的挂车和牵引车的牵引爪规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AUTOMOBILE SERIES BS AU28:1964 (Supersedes S.M.M.T. Standard No.63) Specification for Towing jaw for use between trailers of535 tons gross weight and towing vehicle UDC 629.11.013.5:629.11.013.35BSAU28:1964 This British Standard, having been approved by the AutomobileIndustry Standa

2、rdsCommittee and endorsed by the Chairman of theEngineering Divisional Council, was published undertheauthority of the GeneralCouncil of the Institutionon 15June1964 BSI 02-2000 The following BSI reference relates to the work on this standard: Committee reference AUE/- ISBN 0 580 34551 3 Amendments

3、issued since publication Amd. No. Date CommentsBSAU28:1964 BSI 02-2000 i Contents Page Foreword ii 1 Scope 1 2 Materials 1 3 Dimensions 1 4 Design 1 5 Mounting 1 6 Marking 1BSAU28:1964 ii BSI 02-2000 Foreword This British Standard which is published under the authority of the Automobile Industry Sta

4、ndards Committee of the BSI, is based upon data-sheet SMMT63:1957 of the Society of Motor Manufacturers and TradersLtd. The requirements of this standard, which relate only to vehicles used on the public highways, are intended to ensure the maximum degree of interchangeability between commercial and

5、 Government department and Services standards. Towing jaws may be forged(as shown in Figure) or cast. The material specifications are for the minimum qualities acceptable, and do not exclude the use of other materials provided that these are at least equal in quality so that road safety is not impai

6、red. This standard should be used in conjunction with BS AU29 1) . The jaw has been designed to accommodate a drawbar eye of3in internal diameter and 1 5 / 8in stock. The standard applies to connections to trailers of535 tons gross weight. Thespecification for a towing jaw for connections to trailer

7、s of514 tons gross weight is given in BS AU26 2) , and for trailers of25 tons gross in BSAU24 3) . NOTEIf it is required to convert the figures in this standard from British units into metric units it is recommended that the conversion factors and tables contained in BS350, “Conversion factors and t

8、ables”, be used. Attention is drawn to BS2856, “Precise conversion of inch and metric sizes on engineering drawings”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a

9、 British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 and2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This w

10、ill be indicated in the amendment table on the inside front cover. 1) BS AU29, “Drawbar eyes and forecarriage pins for connection between trailers of535 tons gross weight and towing vehicle”. 2) BS AU26, “Towing jaw for use between trailers of514 tons gross weight and towing vehicle”. 3) BS AU24, “T

11、owing connections for trailers of25 tons gross weight”.BSAU28:1964 BSI 02-2000 1 1 Scope This British Standard specifies the basic dimensions and quality of materials for a towing jaw and its mountings, for use in connection between a towing vehicle and a trailer of535 tons gross weight. The gross w

12、eight refers to gross laden train weights where more than one trailer is drawn. 2 Materials The jaw shall be made from a material of quality not less than BS970 4) . En3A for the forged jaw, or BS592A 5)for the cast jaw, both materials to be in their normalized condition. The towing pin shall be mad

13、e from a material of quality not less than BS970 4) . En16S. 3 Dimensions Dimensions shall be as shown in the Figure. Theringed dimensions are essential for interchangeability, other dimensions apply to the forged jaw and are for guidance only. NOTEThe dimensions specified for the forged jaws have b

14、een calculated on the basis of the total yield strength being not less than two thirds of the gross weight being towed, It is necessary that any other parts not covered by this standard, connecting the coupling to the towing vehicle shall have a similar strength. 4 Design An efficient safety locking

15、 device shall be provided as indicated in the Figure to prevent accidental extraction of the towing pin from the jaw. The jaw shall be so designed that a bar1 3 / 4in diameter may be passed freely between the pin and the inside face of the jaw(seeFigure). 5 Mounting The jaw shall be mounted with fou

16、r bolts, 3 / 4in diameter, at4in 4 in centres. This renders it interchangeable in mounting with hooks specified in BS AU25 6)and BS AU27 7) , and with certain Government department and Services standard hooks. Bolts and nuts shall comply with: i) BS1083, threaded BSF, code symbol R, or 8) ii) BS1768

17、, threaded UNF, code symbol R 9) . The nuts shall be secured either by peening the end of the bolt or by fitting a positive locking device such as a safe locking nut or a slotted nut and split pin. 6 Marking The following wording, in clear lettering 3 / 8in high, raised or impressed, shall be marked

18、 on each towing jaw: “TO TOW35 TONS GROSS” on one side, and on the other side BS AU28”. 4) BS970, “Wrought steels in the form of bars, billets and forgings, up to6in ruling section, for automobile and general engineering purposes. En series”. 5) BS592, (included in BS3100) “Carbon steel castings for

19、 general engineering purposes”. 6) BS AU25, “Towing hook for use between trailers of514 tons gross weight and towing vehicle”. 7) BS AU27, “Towing hook for use between trailers of535 tons gross weight and towing vehicle”. 8) BS1083, “Precision hexagon bolts, screws and nuts”. 9) BS1768, “Unified pre

20、cision hexagon bolts, screws and nuts(UNC and UNF thread normal series)”.BSAU28:1964 2 BSI 02-2000blankBS AU28:1964 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on stan

21、dards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality o

22、f our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offer

23、s members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001

24、. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standard

25、s through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with

26、 standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of

27、 the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior wr

28、itten permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.