ASTM F2653-2011(2015) Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders《与经认可气瓶共同使用的彩弹阀门阳螺纹连接的标准规格》.pdf
《ASTM F2653-2011(2015) Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders《与经认可气瓶共同使用的彩弹阀门阳螺纹连接的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2653-2011(2015) Standard Specification for Paintball Valve Male Threaded Connection for Use with Approved Cylinders《与经认可气瓶共同使用的彩弹阀门阳螺纹连接的标准规格》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2653 11 (Reapproved 2015) An American National StandardStandard Specification forPaintball Valve Male Threaded Connection for Use withApproved Cylinders1This standard is issued under the fixed designation F2653; the number immediately following the designation indicates the year oforig
2、inal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the male threaded connectionused to c
3、onnect a CO2Control Valve or Compressed AirRegulator with an output pressure of 10 342 kPa (1800 psig) orless for use with a paintball marker to a DOT approvedcylinder.1.2 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.3 This st
4、andard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1
5、 ASTM Standards:2D2240 Test Method for Rubber PropertyDurometer Hard-nessF1750 Specification for Paintball Marker Threaded-Propellant Source InterfaceF2030 Specification for Paintball Cylinder Burst Disk As-semblies2.2 Military Standards:3AMS7277 O-Ring Dash SizesMS28775 Packing, Preformed, Hydrauli
6、c, +275 Deg. F(“O”-Ring)2.3 CGA Standards:4CGA S-1.1 Pressure Relief Device Standards-Part1-Cylinders for Compressed Gases2.4 Federal Standards:5FED-STD-H28/9A 24 March 1989 Federal Standard Screw-Thread Standards for Federal Services Section 9 GasCylinder Valve Outlet and Inlet ThreadsNBS Handbook
7、H-282.5 Code of Federal Regulations:6DOT 49 CFR 173DOT 49 CFR 178DOT CFFC 4th Revision2.6 ANSI Standards:7ANSI Y14.5M1994 Dimensioning and Tolerancing3. Connector Gender Assignment3.1 The male connector is that connector which is config-ured as part of the CO2control valve or compressed airregulator
8、 for use with a paintball marker.3.2 The female connector is that connector which is config-ured as part of the DOT approved cylinder.4. Materials and Manufacture4.1 The male connector shall be made from materials thatare compatible with CO2, compressed air or gaseous nitrogen.4.2 The O-ring seal sh
9、all be made from an elastomercompatible with CO2, compressed air or gaseous nitrogen usedto power paintball markers. The O-ring seal shall have ahardness that will register a Type A durometer reading ofbetween 70 to 90 6 5. The O-ring shall conform dimensionallyto the requirements in AMS7277 or MS28
10、775 based upon thesize and material recommendations of the cylinder manufac-turer.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.24 on Paintball and Equipment.Current edition
11、 approved April 1, 2015. Published August 2015. Originallyapproved in 2007. Last previous edition approved in 2011 as F2653 11. DOI:10.1520/F2653-11R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSta
12、ndards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.4Available from Compressed Gas Association (CGA), 4221
13、Walney Rd., 5thFloor, Chantilly, VA 20151-2923, http:/.5Available from The National Conference on Weights and Measures, 15245Shady Grove Road, Suite 130, Rockville, MD 20850.6Available from U.S. Department of Transportation, 400 7th Street, SW,Washington, D.C. 20590.7Available from American National
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF265320112015STANDARDSPECIFICATIONFORPAINTBALLVALVEMALETHREADEDCONNECTIONFORUSEWITHAPPROVEDCYLINDERS
链接地址:http://www.mydoc123.com/p-539196.html