ASTM F2435-2012 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe《钢带增强聚乙烯 (PE) 波纹管的标准规范》.pdf
《ASTM F2435-2012 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe《钢带增强聚乙烯 (PE) 波纹管的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2435-2012 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe《钢带增强聚乙烯 (PE) 波纹管的标准规范》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2435 07 F2435 12 Am American National StandardStandard Specification forSteel Reinforced Polyethylene (PE) Corrugated Pipe1This standard is issued under the fixed designation F2435; the number immediately following the designation indicates the year oforiginal adoption or, in the case
2、of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements and test methods for materials, dimensions, workmanshi
3、p, elongation, impactresistance, pipe stiffness, perforations, and markings for steel reinforced corrugated polyethylene (PE) piping systems of nominalsizes 8 in. (200 mm), through 80 in. (2000 mm). The steel reinforced polyethylene pipes governed by this standard are intendedfor use in underground
4、applications where soil provides support for their flexible walls. These pipes will be used to collect orconvey stormwater runoff for storm sewers and drainage pipes, or both.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalcon
5、versions to SI units that are provided for information only and are not considered standard.1.3 There is no similar or equivalent ISO standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standa
6、rd to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A591/A591M Specification for Steel Sheet, Electrolytic Zinc-Coated, for Light Coating Weight Mass Applications (Withdrawn2005)3A653
7、/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by theHot-Dip ProcessA1008/A1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-StrengthLow-Alloy with Improved Formability, Solution Hardened, and
8、 Bake HardenableD618 Practice for Conditioning Plastics for TestingD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of Ext
9、ernal Loading Characteristics of Plastic Pipe by Parallel-Plate LoadingD3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric SealsD3350 Specification for Polyethylene Plastics Pipe and Fittings MaterialsF412 Terminology Relating to Plastic Piping SystemsF449 Pra
10、ctice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table ControlF477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic PipeF2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance o
11、f HDPEResins or HDPE Corrugated Pipe2.2 AASHO Standard4Standard Specification for Highway Bridges, Division II, Section 30, “Metal Culverts.”2.3 Federal Standards:5Fed. Std. No. 123 Marking for Shipment (Civil Agencies)1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic P
12、iping Systems and is the direct responsibility of Subcommittee F17.11 on Composite.Current edition approved May 1, 2007July 1, 2012. Published June 2007August 2012 Originally approved in 2005. Last previous edition approved in 20052007 asF24350507. DOI: 10.1520/F2435-07.10.1520/F2435-12.2 For refere
13、nced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced
14、on www.astm.org.4 Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001.5 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098.This
15、document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions
16、 as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.4 Military Standards:5MIL-STD-129 Marking for Shipm
17、ent and Storage3. Terminology3.1 DefinitionsDefinitions used in this specification are in accordance with Terminology F412, unless otherwise noted.3.2 Definitions of Terms Specific to This Standard:3.2.1 double-wall, double-wall steel reinforced polyethylene corrugated pipe, adjnpolyethylene corruga
18、ted pipe with steelreinforcing helical V-shaped profilesprofile encapsulated within the corrugations and with ana closed channel on the inside of thepipe (See Fig. 12).3.2.2 single-wall, single-wall steel reinforced polyethylene corrugated pipe, adjnpolyethylene corrugated pipe with steelreinforcing
19、 helical V-shaped profilesprofile encapsulated within the corrugations and with aan open channel on the inside of thepipe (See Fig. 21).3.2.3 triple-wall, adjpolyethylene corrugated pipe with steel reinforcing profiles either helical V-shaped profiles or U-shapedprofiles encapsulated within the corr
20、ugations and with steel reinforcing helical flat profiles encapsulated within the exteriorpolyethylene layer and with a closed channel (polyethylene layer) on the inside of the pipe (See Fig. 3 and Fig. 4).3.2.4 Steel Reinforced Polyethylene Corrugated Pipe (SRPCP), nsingle wall, double wall or trip
21、le wall, helical (spiral)corrugated pipe with steel reinforcing ribs, either V-shaped or U-shaped, encapsulated within polyethylene.4. Significance and Use4.1 Steel reinforced corrugated PE pipes are used for underground applications where soil provides support to their flexiblewalls. Their major us
22、e is to collect or convey storm water run-off for sewers and drains, or both.4.2 Exclusions from recommended use:4.2.1 Permanent exposure to sunlight and exposure to chemicals whose compatibility with the pipe and fittings is not known.5. Materials5.1 Polyethylene Materials:5.1.1 Polyethylene compou
23、nds used in the manufacture of steel reinforced corrugated PE drainage pipe shall meet or exceedthe requirements of cell classification of 444430C333430C as defined and described in Specification D3350.FIG. 21 Single - Wall Single-Wall Steel Reinforced Corrugated Polyethylene Pipe Types I, III and I
24、VF2435 1225.1.2 Slow crack growth resistance of the polyethylene natural resin compound shall be determined by testing in accordancewith Test Method F2136. The applied stress shall be 600 psi (4100 kPa). The test specimens must exceed 2441 h with no failures.Testing shall be done on polyethylene mat
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF24352012STANDARDSPECIFICATIONFORSTEELREINFORCEDPOLYETHYLENEPECORRUGATEDPIPE 增强 聚乙烯 PE 波纹管 标准规范 PDF

链接地址:http://www.mydoc123.com/p-538699.html