ASTM F824-1993(2004) Standard Specification for Tables Mess Marine Steel《船用钢制餐桌》.pdf
《ASTM F824-1993(2004) Standard Specification for Tables Mess Marine Steel《船用钢制餐桌》.pdf》由会员分享,可在线阅读,更多相关《ASTM F824-1993(2004) Standard Specification for Tables Mess Marine Steel《船用钢制餐桌》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 824 93 (Reapproved 2004)An American National StandardStandard Specification forTables, Mess, Marine, Steel1This standard is issued under the fixed designation F 824; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th
2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of round,square, and rectangular marine mess tables with or with
3、outadjustable lee rails for use in crew, officer, and passengerdining areas aboard ship.1.2 The values stated in inch-pound units are to be regardedas the standard. The metric equivalents, given in parentheses,are provided for information only.2. Referenced Documents2.1 ASTM Standards:2A 53/A 53M Sp
4、ecification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and SeamlessA 167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and StripA 240/A 240M Specification for Heat-Resisting Chromiumand Chromium-Nickel Stainless Steel Plate, Sheet, andStrip for Pres
5、sure Vessels and for General ApplicationsA 366/A 366M Specification for Commercial Steel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled3A 500 Specification for Cold-Formed Welded and SeamlessCarbon Steel Structural Tubing in Rounds and ShapesA 501 Specification for Hot-Formed Welded and Seaml
6、essCarbon Steel Structural TubingA 567/A 567M Specification for Castings, Iron, Cobalt, andNickel-Base Alloy, for High Strength at Elevated Tempera-tures3A 569/A 569M Specification for Steel, Carbon (0.15 Maxi-mum, Percent), Hot-Rolled Sheet and Strip Commercial3A 582/A 582M Specification for Free-M
7、achining StainlessSteel BarsB 221 Specification for Aluminum and Aluminum-AlloyExtruded Bars, Rods, Wire, Profiles, and TubesD 907 Terminology of Adhesives2.2 National Electrical Manufacturers Association:NEMA LD-3 High Pressure Decorative Laminates42.3 American Institute of Steel Construction Manua
8、l:AISC Wire and Sheet Metal Gages Equivalent Thicknessin Decimals of an Inch, U.S. Standard Gage (USSG) forUncoated Hot and Cold Rolled Sheets53. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 mess tablea dining table for use in crew, officer, orpassenger dining areas, consistin
9、g of a horizontal top assemblyand one or more supporting pedestals.3.1.2 table topthe assembled horizontal surface of themess table including the substrate, top covering, lee rails, andedge binder, or all of the preceding.3.1.2.1 substratethe structural core of the top assembly.3.1.2.2 top coveringt
10、he decorative melamine laminateattached to the top surface of the substratae.3.1.2.3 Lee Rails:(1) fixed lee raila trim piece at the edge of the table topthat projects above the upper surface of the table top to retaintableware and act as an edge binder.(2) adjustable lee raila trim piece at the edg
11、e of the tabletop that can be raised above the upper surface of the table topto retain tableware and can be retracted when not needed.3.1.2.4 edge binderthe finishing strips of metal applied tothe edge of the table top.3.1.2.5 cleanoutan interruption in the raised portion of thelee rail to facilitat
12、e cleaning of table top.3.1.2.6 pedestala round or square tubular column, orstanchion, that supports the table top. Each pedestal has atable-support plate at its upper end and provisions at the bottomfor attaching to the structural deck.(1) table support platea flanged, dished plate or flat platewit
13、h gussets welded to top of pedestal for supporting andattaching to the table top.3.1.2.7 deck socketa metal sleeve or adaptor welded to thestructural deck, over which the table pedestal is installed andattached.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Te
14、chnology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved 1983. Last previous edition approved in 1999 as F 824 93 (1999).2For referenced ASTM standards, visit the ASTM website,
15、www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from the National Electrical Manufacturers Association, 1300 N.17th St., Suite 1847, Rosslyn, V
16、A 22209.5Available from the American Institute of Steel Construction, One E. WackerDr., Suite 3100, Chicago, IL 606012001.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Classification4.1 Types:4.1.1 Type IRound mess table with si
17、ngle pedestal.4.1.2 Type IISquare mess table with single pedestal.4.1.3 Type IIIRectangular mess table.4.1.3.1 Grade 1Rectangular table with single pedestal.4.1.3.2 Grade 2Rectangular table with two pedestals.4.2 Classes:4.2.1 Class ATable with fixed lee rails.4.2.2 Class BTable with adjustable lee
18、rails.5. Ordering Information5.1 Orders for materials under this specification shall in-clude the following:5.1.1 Quantity and size of each type, grade, and class.5.1.2 Paint:5.1.2.1 ColorThe purchaser shall pick from manufactur-ers samples or submit a sample chip of color desired.5.1.2.2 Manufactur
19、ers standard baked enamel will be fur-nished unless otherwise required and indicated by the pur-chaser.5.1.3 Color or pattern of melamine laminate top covering.5.1.4 If pedestal deck sockets are required, they shall bespecified in the ordering document; otherwise, the table manu-facturer shall have
20、the option of supplying pedestals withoutsockets but with 2 in. (51 mm) of scribing for trimming andwelding to the deck on the ship.5.1.5 If the total weight of the table assembly is required, itshall be requested by the purchaser.6. Materials and Manufacture6.1 For typical design, see Fig. 1, Fig.
21、2, and Fig. 3.6.2 Tops:6.2.1 Tops shall be steel construction with a decorativemelamine laminate top cover. The minimum thickness for thetop plate, stiffener, and edge channels shall be 16 USSG(0.0598 in. or 1.50 mm) and made from cold-rolled steel sheetof commercial quality in accordance with Speci
22、fication A 366/A 366M.6.2.2 The top cover shall be a high-pressure melaminelaminate in accordance with NEMA Specification LD-3 with amaximum thickness of116 in. (2 mm) securely bonded to thetop plate.6.2.3 Lee Rails, Fixed and Adjustable, shall be anodizedaluminum alloy 6063-T1 in accordance with Sp
23、ecificationB 221. Studs for attaching to table top shall be Type 300stainless steel in accordance with Specification A 582/A 582M.6.2.4 Edge Binder for Tables with Adjustable Lee Rails,shall be flush with top of table and may be either anodizedaluminum alloy 6063-T1 in accordance with SpecificationB
24、 221 or polished Type 300 stainless steel in accordance withSpecification A 240/A 240M, at the option of table manufac-turer.6.2.5 Cleanouts, shall be provided as indicated in Figs. 1-3.6.3 Pedestals:6.3.1 Pedestal quantity and sizes shall be as specified inTables 1-6 as illustrated in Figs. 1-3. Co
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF82419932004STANDARDSPECIFICATIONFORTABLESMESSMARINESTEEL 钢制 餐桌 PDF
链接地址:http://www.mydoc123.com/p-537338.html