ASTM F822-1993(2017) Standard Specification for Chest of Drawers (Chiffonier) Steel Marine《船用钢制五斗橱(柜)的标准规格》.pdf

《ASTM F822-1993(2017) Standard Specification for Chest of Drawers (Chiffonier) Steel Marine《船用钢制五斗橱(柜)的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM F822-1993(2017) Standard Specification for Chest of Drawers (Chiffonier) Steel Marine《船用钢制五斗橱(柜)的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F822 93 (Reapproved 2017) An American National StandardStandard Specification forChest of Drawers (Chiffonier), Steel, Marine1This standard is issued under the fixed designation F822; the number immediately following the designation indicates the year of originaladoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of marinechests of drawers (chiffoniers) of steel

3、 construction to be usedin staterooms and other spaces.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 AST

4、M Standards:2A366/A366M Specification for Commercial Steel (CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled(Withdrawn 2000)3D907 Terminology of AdhesivesF825 Specification for Drawers, Furniture, Marine, SteelF826 Specification for Tops, Furniture, Marine, Steel2.2 AISC Manual:4AISC Wire and Sh

5、eet Metal Gauges Equivalent Thickness inDecimals of an Inch, U.S. Standard Gauge (USSG) forUncoated Hot and Cold Rolled Sheets3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chest of drawers (chiffonier)a chest of drawers withfour drawers. All four drawers may be of the same s

6、ize.4. Ordering Information4.1 Orders for items purchased under this specification shallinclude the following information:4.1.1 Quantity.4.1.2 Paint:4.1.2.1 ColorPurchaser shall pick from manufacturerssamples or submit sample chip of color desired.4.1.2.2 Manufacturers standard baked enamel will be

7、fur-nished unless otherwise required and indicated by the pur-chaser.4.1.3 Options for Tops:4.1.3.1 Unless otherwise specified in the orderingdocuments, the top supplied by the furniture manufacturer maybe, at his option, Type I, II, III, or IV in accordance withSpecification F826.4.1.3.2 Color or p

8、attern of top covering material shall bespecified.4.1.4 Options for Drawers:4.1.4.1 Padlock eyes shall be furnished on each drawerwhen specified in ordering documents. This security device isnormally used in crew living spaces.4.1.4.2 Drawer locks shall be furnished when specified inordering documen

9、ts. Master keying of drawer locks will not beprovided unless required and defined by the ordering docu-ments. Instead, each drawer lock will be keyed differently. SeeSpecification F825 for lock description.4.1.4.3 A security panel between the two middle drawers toprovide two secure two-drawer storag

10、e areas for two crewmembers is only furnished when specified in ordering docu-ments. All four drawers in this type chest will be of same size.4.1.5 If the total weight of the chest of drawers is required,it shall be requested by the purchaser.5. Materials and Manufacture5.1 For typical design, see F

11、ig. 1.5.2 Sheet metal shall be in accordance with SpecificationA366/A366M, commercial quality.5.2.1 Minimum sheet metal thicknesses shall be:5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2mm).5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).5.3 J

12、oining of Metal Components:5.3.1 Metal components shall be joined by welding orgluing with a structural adhesive as defined in TerminologyD907. The back panel may be riveted to the case providedrivets are not visible after installation.1This specification is under the jurisdiction of ASTM Committee

13、F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Jan. 1, 2017. Published January 2017. Originallyapproved in 1983. Last previous edition approved in 2010 as F822 93 (2010).DOI: 10.1520/F0822-93R17.2For

14、referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenc

15、ed onwww.astm.org.4Available from American Institute of Steel Construction (AISC), 130 E.Randolph St., Suite 2000, Chicago, IL 60601-6219, http:/www.aisc.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard w

16、as developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.3.2 Joini

17、ng shall be adequate to prevent racking of chestduring handling.5.3.3 Spotwelds shall be spaced approximately 3 in. (76mm) on centers.5.3.4 Visible spotwelds, higher than the general surface ofthe adjacent metal, shall be ground flush.5.3.5 Visible spotweld depressions shall be spot filled andsanded

18、 flush.5.4 Side panels shall be suitably stiffened to prevent buck-ling or oil-canning.5.5 Sound deadening shall be vermin proof and applied toback and inner face of sides of chest. Location and thickness ofapplied sound deadener shall be as required to sound-deadenchest.5.6 Top shall be manufacture

19、d in accordance with Specifi-cation F826.5.7 Drawers shall be manufactured in accordance withSpecification F825.5.8 A furniture base shall be provided suitable for securingchest of drawers to deck.6. Performance Requirements6.1 The completed chest of drawers, with the top anddrawers installed, shall

20、 satisfy the corresponding performancerequirements outlined in Specifications F825 and F826.7. Dimensions7.1 For dimensions, see Table 1.8. Workmanship, Finish, and Quality Assurance8.1 All workmanship and material shall be of specifiedquality in keeping with the best commercial marine practice soas

21、 to produce each item suitable for its intended use.8.2 All exposed burrs, raw or sharp edges which might beinjurious to personnel shall be removed.NOTE 1For description of Type I, II, III, and IV tops, see Specification F826.NOTE 2For description of drawers, see Specification F825.NOTE 3For optiona

22、l security panel, see 4.1.4.3.NOTE 4If chest of drawers is located in a corner, Dimension “E” next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimumvalue for Dimension “E” shall be34 in. (19.05 mm).NOTE 5The minimum value for Dimension “F” shall be 4 in. (102 mm).FIG. 1 Ch

23、est of DrawersTABLE 1 Chest of Drawers DimensionsDesignationin. mmDimension Tolerance Dimension ToleranceWidth A 36116 914 2Height B 37116 940 2Depth C 21116 533 2Toe D 3116 76 2Space,FrontToe EA4 max116 102 max 2Space,SideBase FB434 max116 121 max 2HeightAIf chest of drawers is located in a corner,

24、 Dimension E next to this adjacent wallshall be 0 in. (0 mm). In all other cases, the minimum value for Dimension E shallbe34 in. (19 mm).BThe minimum value for Dimension F shall be 4 in. (102 mm).F822 93 (2017)28.3 Depressions considered unacceptable for products enduse shall be spot filled and san

25、ded smooth.8.4 Finish:8.4.1 All steel surfaces, unless corrosion resistant or with acorrosion-resistant plating, shall be painted so as to preventcorrosion.8.4.2 Unless otherwise required by the ordering documents,all parts normally visible on the completed unit shall have themanufacturers standard

26、baked-on enamel finish.8.4.3 Color is to be specified in the ordering documents.9. Inspection and Certification9.1 Manufacturer shall inspect and certify that the item offurniture complies with the furniture specification and theloading requirements as defined in Section 6.10. Packaging and Package

27、Marking10.1 Each item shall be marked in accordance with thepurchase order.10.2 Packaging shall be provided and shall be acceptable toa common carrier.11. Keywords11.1 chest of drawers; chiffoniers; marine chest of drawers;marine furnitureASTM International takes no position respecting the validity

28、of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject t

29、o revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.

30、 Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is

31、copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 93 (2017)3