ASTM F1871-2002e1 Standard Specification for Folded Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation 《现有下水道和管线修复用A型折叠 成型聚氯乙烯管的标准规范》.pdf

《ASTM F1871-2002e1 Standard Specification for Folded Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation 《现有下水道和管线修复用A型折叠 成型聚氯乙烯管的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1871-2002e1 Standard Specification for Folded Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation 《现有下水道和管线修复用A型折叠 成型聚氯乙烯管的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1871 02e1An American National StandardStandard Specification forFolded/Formed Poly (Vinyl Chloride) Pipe Type A forExisting Sewer and Conduit Rehabilitation1This standard is issued under the fixed designation F 1871; the number immediately following the designation indicates the year

2、oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTETables 1, 3 and 4 were editorially corrected in May 2005.1. Sc

3、ope1.1 This specification covers requirements and test methodsfor materials, dimensions, workmanship, flattening resistance,impact resistance, pipe stiffness, extrusion quality, and a formof marking for folded/formed poly (vinyl chloride) (PVC) pipefor existing sewer and conduit rehabilitation.1.2 P

4、ipe produced to this specification is for use in non-pressure sewer and conduit rehabilitation where the foldedPVC pipe is installed into and then expanded to provide a closefit to the wall of the original conduit, forming a new structuralpipe-within-a-pipe.NOTE 1For installation procedures refer to

5、 Practice F 1867.1.3 This specification includes pipe made only from mate-rials specified in Section 6. This specification does not includepipe manufactured from reprocessed, recycled, or reclaimedPVC.1.4 The values stated in inch-pound units are to be regardedas the standard. The SI units given in

6、parentheses are providedfor information only.1.5 The following precautionary statement pertains only tothe test method portion, Section 11, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the user

7、of this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.1.6 There is no similar or equivalent ISO Standard.2. Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioning Plastics for TestingD 638 Test Me

8、thod for Tensile Properties of PlasticsD 648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD 790 Test Method for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating MaterialsD 1600 Terminology for Abbreviated Terms Rela

9、ting toPlasticsD 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD 2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride) (PVC) Pipe

10、and Molded Fittings byAcetone ImmersionD 2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD 2444 Test Method for Determination of Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup (Falling Weight)F 412 Terminology Rel

11、ating to Plastic Piping SystemsF 1057 Practice for Estimating the Quality of ExtrudedPoly(Vinyl Chloride) (PVC) Pipe by Heat Reversion Tech-niqueF 1867 Practice for Installation of Folded/Formed Poly(Vinyl Chloride) (PVC) Pipe Type A for Existing Sewerand Conduit Rehabilitation2.2 Federal Standard:3

12、Fed. Std. No. 123 Marking for Shipment (Civil Agencies)2.3 Military Standard:3MIL-STD-129 Marking for Shipment and Storage3. Terminology3.1 Definitions: Definitions are in accordance with Termi-nology F 412, and abbreviations are in accordance with Ter-minology D 1600, unless otherwise specified. Th

13、e abbreviationfor poly(vinyl chloride) plastics is PVC.1This standard is under the jurisdiction of Committee F17 on Plastic PipingSystems and is the direct responsibility of Subcommittee F17.67 on TrenchlessPlastic Pipline Technology.Current edition approved Sept. 10, 2002. Published December 2002.

14、Originallyapproved in 1998. Last previous edition approved in 1998 as D187198e2.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page

15、onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 191115094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.1 The term TYPE A is not an abbr

16、eviation, but rather anarbitrary designation for PVC compounds with a minimumvalue for modulus in tension as listed in 6.1 and a maximumvalue as defined by cell limit 1 of Specification D 1784.3.2 Definitions of Terms Specific to This Standard:3.2.1 folded pipe, npipe that has been manufactured andc

17、alibrated round, then subsequently cooled and deformed intoa folded shape for use in existing sewer and conduit rehabili-tation (see Fig. 1).3.2.2 formed pipe, nA folded pipe that has been insertedinto an existing sewer or conduit and expanded with steam heatand pressure, and, if required by the man

18、ufacturer, with asqueegee device or similar device to provide a close fit to theexisting pipe (see Fig. 1).3.2.3 formed field sample, nA formed field sample isformed when the folded pipe has been inserted into a mold pipeand expanded with steam heat and pressure, and, if required bythe manufacturer,

19、 with a squeegee device or similar device toprovide a close fit to the mold pipe.4. Significance and Use4.1 This specification is for use by designers and specifiers,regulatory agencies, owners, and inspection organizations whoare involved in the rehabilitation of non-pressure sewers andconduits. Mo

20、difications may be required, depending on specificjob conditions to establish a project specification. The manu-facturer of the product should be consulted for design andinstallation information. Industrial waste disposal lines shouldbe installed only with the specific approval of the cognizantcode

21、authority, since chemicals not commonly found in drainsand sewers and temperatures in excess of 140F (60C) may beencountered.5. Applications of Material5.1 The nominal folded PVC pipe sizes specified in Section8 can be obtained for use in a range of original pipe insidediameters. Table 1 presents re

22、commended ranges that areavailable for each nominal size.6. Materials and Manufacture6.1 Basic MaterialsThe pipe shall be made from virginPVC compound meeting all the requirements for cell classifi-cation 12111 as defined in Specification D 1784 and withminimum physical properties as listed below:Te

23、nsile Strength Test Method D 638 3 600 PSI (25 MPa)Tensile Modulus Test Method D 638 155 000 PSI (1069 MPa)Flexural Strength Test Method D 790 4 100 PSI (28 MPa)Flexural Modulus Test Method D 790 145 000 PSI (1000 MPa)Heat Deflection Test Method D 648 115F (46C)Temperature tested at264 psi(2 MPa)6.1

24、.1 Compounds meeting the above minimum propertiesthat have different cell classifications because one or moreNOTE 1This figure is intended only for clarification of terms specific to this specification, and shows a representative folded pipe shape. Other foldedpipe shapes may meet the requirements o

25、f this specification.FIG. 1 Folded Pipe and Formed PipeClarification of TermsF187102e12properties are greater than those of the specified compoundsare also acceptable, except modulus in tension shall not exceed280 000 psi.6.2 Rework MaterialClean rework material from this typeof pipe, generated from

26、 the manufacturers own productionmay be used by the same manufacturer, provided that therework material meets all the requirements of 6.1 and that thepipe produced meets all the requirements of this specification.7. Other Requirements7.1 Pipe FlatteningThere shall be no evidence of split-ting, crack

27、ing, or breaking when the rounded pipe is tested inaccordance with 11.3.7.2 Pipe Impact StrengthThe impact strength of roundedpipe shall not be less than the values given in Table 2 whentested in accordance with 11.4.NOTE 2This test is intended only for use as a quality control test, notas a simulat

28、ed service test.7.3 Pipe StiffnessPipe stiffness values for the roundedpipe shall comply with Table 3, when tested in accordance with11.5.7.4 Extrusion QualityThe extrusion quality of the pipeshall be evaluated by both of the following test methods.7.4.1 Acetone ImmersionThe pipe shall not flake or

29、dis-integrate when tested in accordance with 11.6.1.7.4.2 Heat ReversionThe extrusion quality shall be esti-mated by heat reversion method in accordance with 11.6.2.7.5 Flexural PropertiesFlexural modulus of elasticityvalues for the rounded pipe shall comply with 6.1.8. Dimensions, Mass, and Permiss

30、ible Variations8.1 Formed Pipe DiameterThe average outside diameterof the formed pipe shall meet the requirements given in Table4 with a tolerance of plus or minus 1.0 % when measured inaccordance with 11.2.1.8.2 Formed Pipe wall thickness of the rounded pipe, whenmeasured in accordance with 11.2.2,

31、 shall not be less than thevalues specified in Table 4.9. Workmanship, Finish, and Appearance9.1 The formed pipe shall be homogeneous throughout andfree from visible cracks, holes, foreign inclusions, or otherinjurious defects. The pipe shall be as uniform as commerciallypractical in color, opacity,

32、 density, and other physical proper-ties.10. Sampling10.1 The formed pipe sample preparation shall involve theunfolding and expansion of a folded pipe sample within a splitpipe mold with an inside diameter equal to the nominal outsidediameter as shown in Table 4. A folded pipe sample ofsufficient le

33、ngth, 10 ft (3 m) maximum, to complete the testingrequirements shall be inserted into the split pipe mold andsecured at the ends. The assembly shall then be placed in anenclosed chamber for heating.Ambient pressure steam shall beapplied to the chamber for at least a 15-minute period at aminimum temp

34、erature of 220F (104C). While maintainingthe minimum 220F temperature, the folded pipe shall then beformed by applying internal steam pressure at 5 psig (34 kPa)for a period of 2 minutes. While maintaining the 5 psig internalpressure, transition to air pressure and cool the sample to 100F(38C) or le

35、ss. Remove the rounded sample from the mold fortesting.10.2 The frequency of sampling shall be as agreed upon bythe purchaser and the seller.TABLE 1 Folded PVC Pipe Recommended Size Ranges of UseNOTEThe minimum and maximum recommended existing pipe insidediameters shown are mean inside diameters alo

36、ng the pipe length and arenot intended as absolute limits on localized dimensions. Consult themanufacturer for use of folded PVC pipe for sizes of existing pipe beyondthe recommended ranges shown.Folded PipeNominal Out-side Diameter,in. (mm)Recommended ExistingPipeInside Diameter Range,in. (mm)Resul

37、ting Installed DR RangeMin MaxDR26DR32.5DR35DR414 (102) 3.6 (91) 4.1 (104) 24-27 31-386 (152) 5.7 (145) 6.1 (155) 25-27 31-388 (203) 7.6 (193) 8.2 (208) 25-27 31-38 34-369 (229) 8.6 (218) 9.2 (234) 25-27 31-38 34-3610 (254) 9.5 (241) 10.2 (259) 25-27 31-38 34-3612 (305) 11.6 (295) 12.6 (320) 25-27 3

38、1-38 34-3615 (381) 14.5 (368) 15.4 (391) 25-27 31-38 34-3618 (457) 17.6 (447) 18.2 (462) 34-36 40-42TABLE 2 Minimum Impact Strength at 73F (23C)Pipe Size, in. (mm) Impact Strength, ft-lbf (J)4 (102) 150 (203)6 (152) 210 (284)8 (203) 210 (284)9 (229) 220 (299)10 (254) 220 (299)12 (305) 220 (299)15 (3

39、81) 220 (299)18 (457) 220 (299)TABLE 3 Minimum Pipe Stiffness at 5 % DeflectionPipe Size,in. (mm) Pipe Stiffness, psi (kPa)DR 26 DR 32.5 DR 35 DR 414(102)18(457) 41(281.9)22(151.3)16.5(113.7)11(75.6)TABLE 4 Formed Pipe DimensionsNominalOutsideDiameter,in. (mm)Minimum Wall Thickness, in. (mm)DR 26 DR

40、 32.5 DR 35 DR 414.00 (102) 0.154 (3.91) 0.123 (3.12)6.00 (152) 0.231 (5.87) 0.185 (4.70)8.00 (203) 0.308 (7.82) 0.246 (6.25) 0.229 (5.8)9.00 (229) 0.346 (8.79) 0.277 (7.04) 0.257 (6.5)10.00 (254) 0.385 (9.78) 0.308 (7.82) 0.286 (7.3)12.00 (305) 0.462 (11.73) 0.369 (9.37) 0.343 (8.7)15.00 (381) 0.57

41、6 (14.63) 0.462 (11.73) 0.429 (10.9)18.00 (457) 0.439 (11.15)F187102e1310.3 Initial and retest samples shall be drawn from the sameproduction shift.11. Test Methods11.1 Test ConditionsConduct tests in the Standard Labo-ratory Atmosphere of 73.4 6 3.6F (23 6 2C) and 50 6 5%relative humidity, with tes

42、t specimens conditioned in accor-dance with Procedure A of Test Methods D 618, unlessotherwise specified in the test methods or in this specification.11.2 Formed Pipe Dimensions:11.2.1 Pipe DiametersMeasure the outside diameter ofthe pipe in accordance with the applicable section of TestMethod D 212

43、2. Either a tapered sleeve gage or a verniercircumferential wrap tape accurate to 60.001 in. (60.02 mm)may be used.11.2.2 Wall ThicknessMeasure the wall thickness in ac-cordance with the applicable sections of Test Method D 2122.Make sufficient readings, a minimum of six, to ensure that theminimum t

44、hickness has been determined. Use a cylindricalanvil tubing micrometer accurate to 60.001 in. (60.02 mm).11.3 Pipe FlatteningFlatten three specimens of roundedpipe, 6 in. (152 mm) long, between parallel plates in a suitablepress until the distance between the plates is 40 % of theoutside diameter of

45、 the pipe. The rate of loading shall beuniform and such that the compression is completed within 2 to5 minutes. Remove the load and examine the specimens forevidence of splitting, cracking, or breaking.11.4 Impact ResistanceDetermine the impact resistanceof the rounded pipe in accordance with the ap

46、plicable sectionof Test Method D 2444, using a 20-lb (9 kg) Tup A and the flatplate Holder B. Test six specimens each 6 in. (152 mm) long atthe impact levels given in Table 2. All shall pass. If one fails,test another six specimens. Eleven passes out of 12 tested shallbe acceptable.11.5 Pipe Stiffne

47、ssDetermine the pipe stiffness forrounded pipe specimens using Test Method D 2412. Test threespecimens, each 6 in. (152 mm) long. The pipe stiffness of eachspecimen at 5 % deflection shall equal or exceed the minimumvalue listed in Table 3.11.6 Extrusion Quality:11.6.1 Acetone ImmersionTests shall b

48、e run in accor-dance with Test Method D 2152 on rounded samples, everyproduction lot run. This procedure is used for determining theextrusion quality of extruded PVC plastic pipe as indicated byreaction to immersion in anhydrous acetone. It is applicableonly for distinguishing between unfused and pr

49、operly fusedPVC.11.6.2 Heat ReversionTests shall be run in accordancewith Practice F 1057 on rounded pipe samples, every produc-tion lot run. The rounded pipe shall not exhibit any of theeffects listed in the suggested Interpretation of Results inPractice F 1057.11.6.3 Flexural PropertiesTests shall be run on roundedpipe samples in accordance with Test Method D 790, MethodI, Procedure A, every production lot run.12. Inspection12.1 Inspection of the material shall be made as agreed uponby the purchaser and the seller as part of the purchase c