ASTM E2462-2010 Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV Type I《高机动多用途轮式车(HMMWV)货物床区罩(CBC)的标准性能规范》.pdf

《ASTM E2462-2010 Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV Type I《高机动多用途轮式车(HMMWV)货物床区罩(CBC)的标准性能规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2462-2010 Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV Type I《高机动多用途轮式车(HMMWV)货物床区罩(CBC)的标准性能规范》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2462 10Standard Performance Specification forCargo Bed Cover (CBC) HMMWV, Type I1This standard is issued under the fixed designation E2462; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 ScopeThis specification covers the performance re-quirements for the Type I Cargo Bed Cover (CBC). The Type ICargo Bed Cover is a remov

3、able general purpose rigid enclo-sure for the cargo bed of the M1152A1, M1152A1 with B2Armor Kit, M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). TheType I CBC provides environmental protection and security formission equipment and items of general transport.1.2 Th

4、e values stated in SI units are to be regarded asstandard. The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.3 The following safety hazards caveat pertains only to thetest required portion, Sectio

5、n 4, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior t

6、o use.2. Referenced Documents2.1 ASTM Standards:2E1925 Specification for Engineering and Design Criteria forRigid Wall Relocatable Structures2.2 Army Standards:3ARMY TM 9-2320-280-10 HMMWVS OperatorsManualARMY TM 10-5411-231-13 cover; HMMWV; shelterASTM International takes no position respecting the

7、 validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

8、 subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Hea

9、dquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This st

10、andard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).E2462 109