ASTM D4892-1989(2004) Standard Test Method for Density of Solid Pitch (Helium Pycnometer Method)《固体硬沥青密度的标准试验方法(氦比重瓶比重测定法)》.pdf

《ASTM D4892-1989(2004) Standard Test Method for Density of Solid Pitch (Helium Pycnometer Method)《固体硬沥青密度的标准试验方法(氦比重瓶比重测定法)》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4892-1989(2004) Standard Test Method for Density of Solid Pitch (Helium Pycnometer Method)《固体硬沥青密度的标准试验方法(氦比重瓶比重测定法)》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 4892 89 (Reapproved 2004)An American National StandardStandard Test Method forDensity of Solid Pitch (Helium Pycnometer Method)1This standard is issued under the fixed designation D 4892; the number immediately following the designation indicates the year oforiginal adoption or, in th

2、e case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This

3、 test method covers the determination of pitchdensity by helium pycnometer. It is applicable at a range ofroom temperatures of 15 to 35C.1.2 The values stated in SI units are to be regarded as thestandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated wit

4、h its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D71 Test Method for Relative Density of Solid Pitch andAsphalt (Dis

5、placement Method)D 2320 Test Method for Density (Specific Gravity) of SolidPitch (Pycnometer Method)D 2962 Test Method for Calculating Volume-TemperatureCorrection for Coal-Tar PitchD 4296 Practice for Sampling PitchE11 Specification for Wire-Cloth Sieves for Testing Pur-poses3. Terminology3.1 Defin

6、ition of Term Specific to this Standard:3.1.1 density, as determined by this test methodthe massper unit volume and shall be reported as follows:density, 25C, g/cm3grams per cubic centimeter! (1)4. Summary of Test Method4.1 The sample is pulverized and screened to a givenfraction, then the volume of

7、 a weighed portion of the fractionis determined using a helium pycnometer.5. Significance and Use5.1 This test method is useful in characterizing pitches asone element in establishing uniformity of shipments andsources of supply. With this method, the density is determinedto two decimal places, whic

8、h is sufficient for most applications.If a more precise measurement is required (three decimalplaces), use Test Methods D 2320 or D 71.6. Apparatus6.1 Helium Pycnometer.36.2 Balance, capable of weighing a 150-g specimen towithin 1 mg.6.3 Sieves, U.S. Standard 2.36-mm (No. 8), 600-m (No.30), conformi

9、ng to Specification E11.6.4 Thermometer, for measuring room temperature.7. Bulk Sampling7.1 Samples from shipments shall be taken in accordancewith Practice D 4296 and shall be free of foreign substances.8. Dehydration8.1 All bulk samples suspected of having free moistureshould be air-dried or oven-

10、dried at 50C in a convection orforced-air oven before analyzing.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.Current edition appr

11、oved Nov. 1, 2004. Published November 2004. Originallyapproved in 1989. Last previous edition approved in 1999 as D 489289(1999)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informa

12、tion, refer to the standards Document Summary page onthe ASTM website.3Helium pycnometers available from the following suppliers have been foundsatisfactory for this purpose: (a) Beckman 2500 Harbor Blvd., Fullerton, CA, (b)Micromeritics, 5680 Goshen Springs Rd., Norcross, GA, and (c) Quantachrome,

13、5Aerial Way, Syosset, NY. If you are aware of alternative suppliers, please providethis information to ASTM International Headquarters. Your comments will receivecareful consideration at a meeting of the responsible technical committee1, whichyou may attend.1Copyright ASTM International, 100 Barr Ha

14、rbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9. Preparation of Test Specimen9.1 Crush a 50 to 200-g representative portion of the drypitch until all of it passes the 2.36 mm (No. 8 sieve). Avoidgrinding the pitch. Remove the fines by screening through the600 m (No. 30 sie

15、ve) and use the pitch retained on this sieveas the test specimen.10. Calibration of Helium Pycnometer10.1 Calibrate daily or before using, following instrumentmanufacturers instructions.11. Procedure11.1 Place 10 to 150 g (80 to 90 % of the maximum capacityof the particular holder being used) of the

16、 prepared crushed andsized fraction into the required specimen holder provided withthe instrument. Weigh to the nearest milligram.11.2 Determine volume of pitch following manufacturersinstructions.11.3 Weigh specimen container after determination; if thisweight is lower than the initial weight, the

17、specimen has lostmoisture or volatiles during the density determination. Use thelower weight in determining the density. Also, if the specimenappears to have free moisture, dry the specimen as specified in8.1, and repeat the density determination.11.4 Record the room temperature during the density d

18、eter-mination.12. Calculation12.1 The procedure described in this test method determinesthe volume of a given mass of pitch at the ambient temperature(room temperature) of the helium pycnometer. Since thevolume of a given mass of pitch is temperature-dependent, thedensity of the given specimen will

19、vary with the ambienttemperature. The variation of pitch volume with temperaturehas been previously established (Test Method D 2962 and theliterature4), and the following calculation corrects all densitymeasurements to 25C.12.2 The density of pitch, corrected to 25C, is given by thegeneral formula:d

20、25C5WVt1 6 0.00047 Dt(2)where:W = specimen mass, g,Vt= volume of specimen, cm3, at measurement tem-perature,Dt = difference between 25C and the measurementtemperature, andd25C= pitch density at 25C, g/cm3.The factor 0.00047/C is obtained from the literature4andTest Method D 2962.12.3 Calculate the d

21、ensity of the pitch (to three decimalplaces) using the following equation:d25C5 VtWcorrection factor#(3)The correction factors for measurement temperatures of 15to 35C are given in Table 1.12.4 ExampleA specimen of pitch having a mass of20.027 g was found to have a volume of 15.26 cm3at atemperature

22、 of 30C; the density calculation is as follows:d25C520.027 g15.26 cm30.9985 1.315 g/cm3(4)12.5 Average duplicate results and round off to two decimalplaces.13. Report13.1 Report density of the pitch to two decimal places asfollows: density, 25C, g/cm3.14. Precision and Bias514.1 PrecisionThe followi

23、ng criteria shall be used for theacceptability of results (95 % probability):14.1.1 RepeatabilityDuplicate values by the same opera-tor shall not be considered suspect unless they differ by morethan 0.02.14.1.2 ReproducibilityThe values reported by each of twolaboratories, representing the arithmeti

24、c average of duplicatedeterminations, shall not be considered suspect unless thereported values differ by more than 0.03.14.2 BiasDuring the interlaboratory study to determinethe precision of this test method, the density was also deter-mined by Test Method D 2320 (water pycnometer). It wasfound tha

25、t the density determined by helium pycnometer washigher than that determined by water pycnometer by anaverage value of 0.004.15. Keywords15.1 density; helium pycnometer; pitch4Mapstone, G. E., “Specific Gravity of Coal Tar Fractions,” Journal of AppliedChemistry, October 5, 1955, pp. 582588.5Support

26、ing data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR: D08-1003.TABLE 1 Volume Correction Factors Versus MeasurementTemperatureMeasurement Temperature, C Correction Factor15 1.00516 1.00417 1.00418 1.00319 1.00320 1.00221 1.00222 1.00123 1.00

27、124 1.00025 1.00026 1.00027 0.99928 0.99929 0.99830 0.99831 0.99732 0.99733 0.99634 0.99635 0.995D 4892 89 (2004)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly adv

28、ised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either

29、 reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. I

30、f you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 4892 89 (2004)3