ASTM D4175-2017a Standard Terminology Relating to Petroleum Products Liquid Fuels and Lubricants《石油产品 液态燃料和润滑剂相关标准术语》.pdf

《ASTM D4175-2017a Standard Terminology Relating to Petroleum Products Liquid Fuels and Lubricants《石油产品 液态燃料和润滑剂相关标准术语》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4175-2017a Standard Terminology Relating to Petroleum Products Liquid Fuels and Lubricants《石油产品 液态燃料和润滑剂相关标准术语》.pdf（106页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4175 17D4175 17aStandard Terminology Relating toPetroleum Products, Liquid Fuels, and Lubricants1This standard is issued under the fixed designation D4175; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l

2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This terminology standard covers

3、 the compilation of terminology developed by Committee D02 on Petroleum Products,Liquid Fuels, and Lubricants, except that it does not include terms/definitions specific only to the standards in which they appear.1.1.1 The terminology, mostly definitions, is unique to petroleum, petroleum products,

4、lubricants, and certain products frombiomass and chemical synthesis. Meanings of the same terms outside of applications to petroleum, petroleum products, andlubricants can be found in other compilations and in dictionaries of general usage.1.1.2 The terms/definitions exist in two places: (1) in the

5、standards in which they appear and (2) in this compilation.1.2 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations iss

6、uedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Terminology2.1 Alphabetical listing of terms with definitions for each term showing attributions as to source and subcommittee jurisdictionis in bold print following the definition. Those showing no attributes are unde

7、r the jurisdiction of Subcommittee CS 95. Someabbreviations, acronyms, and symbols are included in the list.3-MPA, n3-methylphenylamine D02.J0 D6812atomic absorption spectrometry, nanalytical technique for measuring metal content of solutions, based on a combination offlame source, hollow cathode la

8、mp, photomultiplier, and a readout device. D02.03 D7740abrasive wear, nwear due to hard particles or hard protuberances forced against and moving along a solid surface. D02.B0D4998; D02.L0 D5182absorbance, nlogarithm to the base 10 of the ratio of the reciprocal of the transmittance. D02.03 D7740abs

9、orbance, (A), nthe molecular property of a substance that determines its ability to take up radiant energy, expressed by:A 5log101T!52log10T! (1)where T is the transmittance.DISCUSSIONAbsorbance expresses the excess absorption over that of a specified reference or standard. It is implied that compen

10、sation has been affected forreflectance losses, solvent absorption losses, and refractive effects, if present, and that attenuation by scattering is small compared with attenuation byabsorption. D02.14 D7996absorbance, A,nthe molecular property of a substance that determines its ability to take up r

11、adiant power, expressed by:A 5log10 1/T!52log10Twhere T is the transmittance.1 This terminology is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.95 on Terminology.Current edition approved Feb. 1, 20

12、17July 15, 2017. Published February 2017August 2017. Originally approved in 1983. Last previous edition approved in 20162017 asD4175 16c.D4175 17. DOI: 10.1520/D4175-17.10.1520/D4175-17A.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication

13、of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be consider

14、ed the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1DISCUSSIONAbsorbance expresses the excess absorption over that of a specified reference or stand

15、ard. It is implied that compensation has been affected forreflectance losses, solvent absorption losses, and refractive effects, if present, and that attenuation by scattering is small compared with attenuation byabsorption. D02.04 D2008absorptivity, a,nthe specific property of a substance to absorb

16、 radiant power per unit sample concentration and path length,expressed by:a 5Af/bcwhere:A = the absorbance,f = the dilution factor,b = sample cell path length, andc = the quantity of absorbing substance contained in a volume of solvent.D02.04 D2008acceptance limit (AL), na numerical value that defin

17、es the point between acceptable and unacceptable quality.DISCUSSIONThe AL is not necessarily the specification limit. It is a value that takes into account the specification limit, the test method precision, and the desiredprobability of product acceptance if the quality is at the specification limi

18、t.D02.94 D3244accepted reference value (ARV), nvalue that serves as an agreed-upon reference for comparison and that is derived as (1) atheoretical or established value, based on scientific principles, (2) an assigned value, based on experimental work of somenational or international organization, s

19、uch as the U.S. National Institute of Standards andTechnology (NIST), or (3) a consensusvalue, based on collaborative experimental work under the auspices of a scientific or engineering group.DISCUSSIONIn the context of this test method, accepted reference value is understood to apply to the ignitio

20、n delay of specific reference materials determined underreproducibility conditions by collaborative experimental work. D02.01 D6890, D02.94 D6299, D6792DISCUSSIONIn the context of this test method, accepted reference value is understood to apply to the Research octane number of specific reference ma

21、terialsdetermined empirically under reproducibility conditions by the National Exchange Group or another recognized exchange testing organization.D02.01 D2699, D2700DISCUSSIONIn the context of this method, accepted reference value is understood to apply to the ignition delay of specific reference ma

22、terials determined underreproducibility conditions by collaborative experimental work. D02.01 D7170DISCUSSIONIn the context of this test method, accepted reference value is understood to apply to the Supercharge and octane number ratings of specific referencematerials determined empirically under re

23、producibility conditions by the National Exchange Group or another recognized exchange testingorganization. D02.01 D909accepted reference value (ARV), na value that serves as an agreed-upon reference for comparison, and which is derived as:(1) a theoretical or established value, based on scientific

24、principles, (2) an assigned or certified value, based on experimentalwork of some national or international organization, or (3) a consensus or certified value, based on collaborative experimentalwork under the auspices of a scientific or engineering group. D02.25 D3764accuracy, nthe closeness of ag

25、reement between a test result and an accepted reference value. D02.94 D6792accuracy, nthe closeness of agreement between an observed value and an accepted reference value.D02.94 D6299, D7372D4175 17a2ACERTAdvanced Combustion Emission Reduction Technology D02.B0 D8047acid number, nthe quantity of a s

26、pecified base, expressed in milligrams of potassium hydroxide per gram of sample, requiredto titrate a sample in a specified solvent to a specified endpoint using a specified detection system.DISCUSSIONIn this test method, acids or salts with dissociation constants greater than 109, are titrated to

27、a green end point with p-naphtholbenzein indicator.D02.06 D3339DISCUSSIONIn this test method, the acid number is calculated from the number of drops required to produce a change in solution color from blue-green to orange,compared to the number of drops required to produce an identical color change

28、using a reference standard. Because this is a direct comparison method,the acid number value can be reported in milligrams of potassium hydroxide per gram of sample. D02.06 D5770DISCUSSIONIn this test method, the indicator is p-naphtholbenzein titrated to a green/green-brown end point in a toluene-w

29、ater-isopropanol solvent. D02.06D974DISCUSSIONThis test method expresses the quantity of base as milligrams of potassium hydroxide per gram of sample, that is required to titrate a sample in amixture of toluene and propan-2-ol to which a small amount of water has been added from its initial meter re

30、ading in millivolts to a meter readingin millivolts corresponding to an aqueous basic buffer solution or a well-defined inflection point as specified in the test method. D02.06 D664DISCUSSIONThis test method provides additional information. The quantity of base, expressed as milligrams of potassium

31、hydroxide per gram of sample, requiredto titrate a sample in the solvent from its initial meter reading in millivolts to a meter reading in millivolts corresponding to a freshly prepared aqueousacidic buffer solution or a well-defined inflection point as specified in the test method shall be reporte

32、d as the strong acid number. D02.06 D664DISCUSSIONThe causes and effects of the so-called strong acids and the causes and effects of the other acids can be very significantly different. Therefore, the userof this test method shall differentiate and report the two, when they are found. D02.06 D664aci

33、dity, nthe quality, state or degree of being acid.DISCUSSIONIn this test method, the criterion for acidity is a pink or red color when methyl orange indicator is used. D02.06 D1093ACMAlkyl Acrylate Copolymer D02.B0 D8047across (or against) grain, ndirection in a body with preferred orientation due t

34、o forming stresses that has the maximum c-axisalignment as measured in an X-ray diffraction test. D02.F0 C709activated sludge, nthe precipitated solid matter, consisting mainly of bacteria and other aquatic microorganisms, that is producedin a domestic wastewater treatment plant; activated sludge is

35、 used primarily in secondary sewage treatment to microbiallyoxidized dissolved organic matter in the effluent. D02.12 D6139activation energy (Ea)measure of temperature effects on the rate of oxidation in the kinetic, or chemical control, regime.Activation energy is calculated from the Arrhenius equa

36、tion:OR5Zexp2Ea/RT!where:OR = oxidation rate,R = 8.314 J mole-1 K-1 is the universal gas constant,T = absolute temperature (in Kelvin), andD4175 17a3Z = pre-exponential factor.The activation energy and pre-exponential factor are calculated from linearized form of Arrhenius equation, that is, from th

37、eslope and intercept of the linear plot of the logarithm of oxidation rate versus the inverse of absolute temperature (1/T):log10 OR!5log10 Z 2Ea/2.303 RT!Activation energy is expressed in units of kJ/mol. Pre-exponential factor is expressed in the same units as the oxidation rates,namely g h-1 m-2

38、(for Za calculated from area-normalized oxidation rates, ORa) or g g-1 h-1 (for Zw calculated from weight-normalized oxidation rates, ORw). D02.F0 D7542active grease-sampling device, ndevice designed to take an active sample of a lubricating grease from a bearing, gear, or driveshaft located in a gr

39、ease-lubricated component. D02.G0 D7718active sampling, vto use a sampling device to actively gather an in-service lubricating grease sample from a grease-lubricatedcomponent. D02.G0 D7718actuate, vto hold the interior cylinder of the active grease-sampling device while pushing the exterior cylinder

40、 forward towardthe grease-lubricated component that is being sampled allowing lubricating grease to fill the sampling device. D02.G0 D7718acute ecotoxicity, nthe propensity of a material to produce adverse behavioral, biochemical, or physiological effects innon-human organisms or populations in a sh

41、ort period of time, usually not constituting a substantial portion of the life span ofthe organism. D02.N0 D6046acute ecotoxicity, nthe propensity of a test material to produce adverse behavioral, biochemical or physiological effects innon-human organisms or populations in a short period, usually no

42、t constituting a substantial portion of the life span. D02.12D6384acute ecotoxicity test, na comparative ecotoxicity test in which a representative subpopulation of organisms is exposed todifferent treat rates of a test material and is observed for a short period, usually not constituting a substant

43、ial portion of theirlife span. D02.12 D6384acute toxicity test, na comparative toxicity test in which a representative subpopulation of organisms is exposed to different treatrates of a test material and is observed for a short period usually not constituting a substantial portion of their life span

44、. D02.12D6081additive, na material added to another, usually in small amounts, to impart or enhance desirable properties or to suppressundesirable properties. D02.B0 D5862additive, nsubstance added to a base aviation gasoline in relatively small amounts that either enables that base aviation gasolin

45、eto meet the applicable specification properties or does not alter the applicable specification properties of that base aviationgasoline beyond allowable limits. D02.J0 D7826adenosine monophosphate, nmolecule formed by the removal of two (2) molecules of phosphate (one pyrophosphate molecule)from AT

46、P. D02.14 D7463adenosine triphosphate, nmolecule comprised of a purine and three phosphate groups, that serves as the primary energytransport molecule in all biological cells.D02.14 D7463adhesive wear(scuffing), nwear due to localized bonding between contacting solid surfaces leading to material tra

47、nsfer betweenthe two surfaces or loss from either surface. D02.L0 D5182adiabaticity, nthe condition in which there is no significant gain or loss of heat throughout the length of the column.DISCUSSIONWhen distilling a mixture of compounds as is the case of crude petroleum, there will be a normal inc

48、rease in reflux ratio down the column. In the casewhere heat losses occur in the column, the internal reflux is abnormally greater than the reflux in the head. The opposite is true when the column gainsheat, as with an overheated mantle. D02.08 D2892adjustment, noperation of bringing the portable di

49、gital density meter to a state of performance suitable for its use, by settingor adjusting the instrument constants.D02.04 D7777aerobe, nan organism that requires oxygen to remain metabolically active.DISCUSSIOND4175 17a4Aerobes use oxygen as their terminal electron acceptor in their primary energy-generating metabolic pathways. Aerobes require oxygen for survival,using aerobic metabolic processes to generate energy for growth and surv