ASTM D2200-2017 Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces《图案表面制备标准和绘制钢表面指南使用的标准实施规程》.pdf
《ASTM D2200-2017 Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces《图案表面制备标准和绘制钢表面指南使用的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2200-2017 Standard Practice for Use of Pictorial Surface Preparation Standards and Guides for Painting Steel Surfaces《图案表面制备标准和绘制钢表面指南使用的标准实施规程》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2200 17 Swedish Standards AssociationStandard SIS 05 59 00ISO 8501SSPC: The Society for Protective CoatingsSSPC VIS 1, VIS 3, VIS 4/NACE VIS 7, VIS 5/NACE VIS 9Danish Standards AssociationDanish Standard DS 2019European Committee of Paint and PrintingInk Manufacturers AssociationStanda
2、rd Practice forUse of Pictorial Surface Preparation Standards and Guidesfor Painting Steel Surfaces1This standard is issued under the fixed designation D2200; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio
3、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 The visual surface preparation guides and st
4、andardsconsist of a series of color prints available as separatepublications. Five different sets of photographs are described inthis standard, designated as Method A (ISO/Swedish Stan-dard2) and Methods B through E (SSPC Guides and ReferencePhotographs3). The methods differ in the depiction of the
5、initialsurface, in the definition and depiction of the cleaningconditions, and in the number of cleaning methods included.Because of these differences, the specifier should state whichguide to use.1.2 The colored visual surface preparation guides representdifferent conditions of hot rolled carbon st
6、eel before and aftersurface preparation. Prior to cleaning, there are four rustgrades, A to D, that cover the range from intact mill scale to100 % rusted and pitted steel. The standards then depict theappearance of the initial conditions after cleaning by one ormore methods (for example, dry abrasiv
7、e blast cleaning) tovarious degrees of thoroughness. In addition, Method Bincludes three painted conditions that contain various degreesof deterioration. The Guide3depicts these conditions aftervarious degrees of dry abrasive blast cleaning. Method Cincludes four rust grades and three painted condit
8、ions thatcontain various degrees of deterioration. The Guide4depictsthese conditions after various degrees of hand and power toolcleaning. Method D includes two rust grades and four paintedconditions that contain various degrees of deterioration. TheGuide5depicts these conditions after various degre
9、es of waterjetting, with three levels of flash rusting. Method E includestwo rust grades. The Guide6depicts these conditions aftervarious degrees of wet abrasive blast cleaning, with threelevels of flash rusting.1.3 This international standard was developed in accor-dance with internationally recogn
10、ized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 Other Documents:Pictorial Surface Prep
11、aration Standards and Guides2,3,4,5,6Surface Cleanliness Definitions3,43. Terminology3.1 Definitions:3.1.1 The cleanliness definitions for the Method A visualsurface preparation standard appear in the text of the pictorial1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRel
12、ated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.46 on Industrial Protective Coatings.The pictorial standards described were prepared by the Swedish CorrosionInstitute and have been jointly approved by ASTM, The Society For ProtectiveCoatings (SSPC) (VIS
13、 1), and the Swedish Standardizing Commission.Current edition approved Dec. 1, 2017. Published December 2017. Originallyapproved in 1966. Last previous edition approved in 2013 as D2200 13. DOI:10.1520/D2200-17.2The pictorial surface preparation standard Method A is available from TheSociety for Pro
14、tective Coatings (SSPC), 800 Trumbull Drive, Pittsburgh, PA15205-4365, http:/www.sspc.org and Sveriges Standardiseringskommission, Box3295, Stockholm 3, Sweden.3The Visual Guide for Method B and surface cleanliness definitions are availablefrom The Society for Protective Coatings (SSPC), 800 Trumbul
15、l Drive, Pittsburgh,PA 15205-4365, http:/www.sspc.org.4The Visual Guide for Method C and the surface cleanliness definitions areavailable from The Society for Protective Coatings (SSPC), 800 Trumbull Drive,Pittsburgh, PA 15205-4365, http:/www.sspc.org.5The Visual Guide for Method D and the surface c
16、leanliness definitions areavailable from The Society for Protective Coatings (SSPC), 800 Trumbull Drive,Pittsburgh, PA 15205-4365, http:/www.sspc.org.6The Visual Guide for Method E and the surface cleanliness definitions areavailable from The Society for Protective Coatings (SSPC), 800 Trumbull Driv
17、e,Pittsburgh, PA 15205-4365, http:/www.sspc.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the De
18、cision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1surface preparation standards publication.2The definitions forMethods B, C, D, and E are found in a separate publication.
19、3,4,5,64. Significance and Use4.1 The appearance of the various degrees of dry and wetabrasive blast cleaning, hand and power tool cleaning andwater jetting are influenced by the initial rust grades of the steelbeing cleaned and/or the type and condition of the coating onthe existing steel. The stan
20、dards and guides aid visually injudging and evaluating the degree of rusting and/or paintdeterioration before cleaning and the degree of cleaning ofsteel surfaces prior to painting.4.2 Five methods have evolved because of differences in thepractice of using visual standards and guides throughout the
21、world, and the method of surface preparation employed. InEurope, the visual standards (Method A) are used as theprimary means of assessing the degree of cleaning. In the US,the SSPC written definitions take precedence with the visualguides and reference photographs used as a supplement. Thevisual gu
22、ides and reference photographs of Methods B, C, andD conform to the SSPC written definitions. There are writtendefinitions for Method E, however, the visual guide for MethodE does not contain a complete set of pictorials corresponding toeach surface cleanliness definition.5. Procedure and Interpreta
23、tionMethod A ISO/Swedish Standard(Hand Tool Cleaning, Power Tool Cleaning, AbrasiveBlast Cleaning, Flame Cleaning)5.1 Determine the method of cleaning to be used (forexample, hand or power tool cleaning, abrasive blast cleaning,or flame cleaning).5.2 Determine the initial condition of the steel acco
24、rding tofour initial grades (conditions).5.2.1 Condition A: Tightly adhering mill scale.5.2.2 Condition B: Mill scale and rust.5.2.3 Condition C: Rusted.5.2.4 Condition D: Rusted and pitted.5.3 Following the cleaning operation, compare the preparedsurface to the photograph corresponding to the speci
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD22002017STANDARDPRACTICEFORUSEOFPICTORIALSURFACEPREPARATIONSTANDARDSANDGUIDESFORPAINTINGSTEELSURFACES

链接地址:http://www.mydoc123.com/p-511185.html