ASTM C1822-2015 Standard Specification for Insulating Covers on Accessible Lavatory Piping《可使用盥洗室绝缘罩的标准规格》.pdf

《ASTM C1822-2015 Standard Specification for Insulating Covers on Accessible Lavatory Piping《可使用盥洗室绝缘罩的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1822-2015 Standard Specification for Insulating Covers on Accessible Lavatory Piping《可使用盥洗室绝缘罩的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1822 15Standard Specification forInsulating Covers on Accessible Lavatory Piping1This standard is issued under the fixed designation C1822; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers insulating covers for use onexposed drain and water supply piping under accessiblelavatories and sinks. The i

3、nsulating covers shall have thermalinsulating properties to protect people with disabilities fromburns and physical harm from contact with exposed watersupply and waste piping under accessible lavatories and sinks.Insulating covers shall be removable and reusable.1.2 Included are criteria for classi

4、fying removable andreusable protective covers on exposed drain and water supplypiping under lavatories and sinks and requirements and testmethods for materials and workmanship. Methods of markingare also given.1.3 The products covered by this specification are intendedfor use on water supply and dra

5、in or waste piping underlavatories and sinks only.1.4 The values stated in inch-pound units shall be regardedas the standard. The values given in parentheses are mathemati-cal conversions to SI units that are provided for informationonly and are not considered standard.1.5 This specification does no

6、t establish the criteria requiredin the design of the equipment over which removable insulat-ing covers are used, nor does this specification establish orrecommend the applicability of removable insulating coversover all surfaces.1.6 This standard does not apply to shrouds under lavatoriesand sinks.

7、1.7 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced D

8、ocuments2.1 ASTM Standards:2C168 Terminology Relating to Thermal InsulationC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC1045 Practice for Calculating Thermal Transmission Prop-erties Under Steady-State Condit

9、ionsD570 Test Method for Water Absorption of PlasticsD635 Test Method for Rate of Burning and/or Extent andTime of Burning of Plastics in a Horizontal PositionE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsG21 Practice for Determining Resistance of Synthetic Poly-meric Mater

10、ials to Fungi2.2 Department of Justice Document:32010 Americans with Disabilities Act Standard for Acces-sible Design Section 606.52.3 ICC/ANSI Standard:4A117.1 Standard for Accessible and Usable Buildings andFacilities, Section 606.62.4 ASME Standard:5A112 18.9 Protectors/Insulators for Exposed Was

11、te and Sup-plies on Accessible Fixtures3. Terminology3.1 For definitions of terms used in this specification, referto Terminology C168.3.2 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct respons

12、ibility of Subcommittee C16.40 onInsulation Systems.Current edition approved Oct. 1, 2015. Published October 2015. DOI: 10.1520/C1822-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume i

13、nformation, refer to the standards Document Summary page onthe ASTM website.3Available from the U.S. Department of Justice, 950 Pennsylvania Ave., NWWashington, DC, 20530-0001, www.ada.gov.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, htt

14、p:/www.ansi.org.5Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.1 accessib

15、leable to be accessed or approached by awheelchair or by people with disabilities.3.2.2 accessible lavatory or sinklavatories or sinks in-stalled to provide access for wheelchairs and people withdisabilities.3.2.3 insulating covermaterial or assembly of materialsthat is applied over piping to provid

16、e thermal protection fromhot and cold temperatures, and physical protection frombruising, abrasion, and cutting from sharp, hard, or abrasivesurfaces.3.2.4 lavatorya fixed washbasin used for personal hygienethat requires a water supply and discharges wastewater to thedrainage systems.3.2.5 removable

17、 and reusablean insulating cover whichcan be installed and then removed and reinstalled for mainte-nance and cleaning.3.2.6 shroudsa cover under a lavatory or sink that isattached to a cabinet or wall and not to piping.3.2.7 sinka fixed bowl or basin for general uses thatrequires a water supply and

18、discharges wastewater to thedrainage system.3.2.8 tepid waterdomestic water with temperature be-tween 60 to 100F (15.6 to 37.8C).3.2.9 waste pipingpiping and pipe fittings under lavatoriesor sinks that drain waste water.3.2.10 water supplypiping and pipe fitting that distributespotable water to a la

19、vatory or sink.4. Significance and Use4.1 Accessibility design standards require water suppliesand drain pipes under lavatories and sink are to be insulated orotherwise configured to protect people with disabilities fromcontact with exposed pipes. No sharp or abrasive surfaces areallowed under lavat

20、ories or sinks.4.2 People in wheelchairs and people with physical disabili-ties are part of the most at risk group for scalding, severereaction, bruising and cuts from exposed piping under lavato-ries and sinks. These groups, which also include youngchildren, the elderly, and the infirm sometimes re

21、quire differentsafety regulation due to but not limited to slower reaction time,physical disabilities, mobility impairments; and medical con-ditions which can increase exposure contact time and increasedvulnerability to severe reaction, discomfort, burns, bruises,abrasions, and cuts of the skin.4.3

22、This specification is intended to cover products whichwill satisfy the requirements of theAmericans with DisabilitiesAct 4.19.4, the Department of Justice: 2010 Americans withDisabilities Act Standard for Accessible Design Section 606.5,ICC/ANSI A117.1 2012 (Standard for Accessible and UsableBuildin

23、gs and Facilities - for Persons with Physical Disabili-ties) section 606.6 (Exposed Pipes and Surfaces).5. Classification5.1 Removable and reusable insulating covers covered bythis specification are classified into four types based upon thefire performance as follows:5.1.1 Type ITest Method E84 Flam

24、e spread/smoke devel-oped indices of 25/450.5.1.2 Type IITest Method E84 Flame spread/smoke devel-oped indices of 200/450.5.1.3 Type IIITest Method D635 Rate of Burning, maxi-mum 1 in. (25 mm).5.1.4 Type IVNo fire performance determined or required.6. Materials and Manufacture6.1 Insulating cover ma

25、terial shall be suitable for moldingor constructed into final required shapes. If rolls or sheets areused, they shall be formed to fit the cylindrical surface to whichthey are to be applied.6.2 The insulating cover for tailpiece and drain pipe sectionsshall be constructed to allow separation into pi

26、eces or to be cutto remove excess material to fit piping configuration.6.3 The insulating cover shall consist of one or more pieces.Component pieces shall be bonded, welded, extruded, ormolded together. Adhesive construction is not permitted.6.4 The insulating cover shall be constructed to create ai

27、rbaffles between the material and the piping.7. Material Application Requirements7.1 The insulating cover shall be in a form suitable forapplication to cylindrical surfaces of exposed drain and watersupply piping.7.2 The insulating cover and fasteners shall not create anysharp or abrasive exterior s

28、urfaces.8. Performance Requirements and Physical Properties8.1 The insulating cover shall conform to the requirementsshown in Table 1.8.2 Exterior Surface Thermal Transfer Test:8.2.1 Test shall be conducted at a room temperature of 73.46 3.6F (23 6 2C), inside a draft shield. The draft shield shallb

29、e 30 in. (76 cm) wide by 30 in. (76 cm) high by 24 in. (61 cm)deep, closed on the top, back and sides, and that is set onto asurface like a benchtop or floor that closes off the bottom,leaving only the front open. This shield simulates an accessiblesink in an alcove. Pipe slots will allow hot water

30、pipes to enterand test sample to be positioned 15 in. above the floor (seeAppendix X1). For testing, one (1) sample of each P-trapassembly (includes tailpiece and waste arm), stop and supplyriser shall have a sample insulating cover installed in accor-dance with the manufacturers instructions.8.2.2

31、Insulating cover fitting more than one size piping shalluse the largest size of the insulating device for testing.8.2.3 Using water tight connections between water heatertank and P-trap, supply stops, supply riser, and waste fitting,maintain water temperature within P-trap, supply stops, riser,and f

32、ixture waste fitting at 140 6 2F (60 6 1.1C) for a periodof 300 minutes. Use thermocouple attached to outside wall ofP-trap, stop, and supply insulation cover. Record the tempera-ture at three different locations to determine the hottest area.Record the temperature every 15 minutes over the length o

33、f thetest.C1822 1528.2.4 Maximum surface temperature of the exterior surfaceof the insulating cover shall not rise above 95F (35C).8.3 Surface Deflection and Load TestWith a12 in. (12.7mm) diameter metal rod, apply a 10 lb (4.5 kg 44.5 N) force ata right angle against the outside surface of cover. H

34、old force inplace for ten seconds.8.3.1 The outside surface shall not crack or show signs ofvoids. After the load is removed for five minutes, the outsidesurface shall have no indentations where the load was applied.9. Dimensions and Permissible Variations9.1 ThicknessThe minimum thickness of insula

35、ting coversshall be 3.175 mm.10. Form and Installation10.1 The insulating cover shall be manufactured in a formsuitable for application to cylindrical surfaces and to covereither 114 in. (32 mm), 112 in. (38 mm), or 2 in. (50.8 mm)multiple sizes of P-traps and vertical and horizontal wastepiping.10.

36、2 The insulating cover shall be manufactured in a formsuitable for application to cylindrical surfaces and to coverwater supply piping and stop valve.10.3 The insulating cover shall fasten in place over drainpiping, P-trap, and water supplies and shall be attached bymechanical fasteners and or conti

37、nuous hook and loop fastener.10.4 Fastening shall withstand dislodgement of insulatingcover from physical contact and maintenance.10.5 Insulating cover shall be removable and re-usable andafter re-assembly shall meet the requirements of this specifi-cation.10.6 Fasteners shall not have, or create, s

38、harp or abrasivesurface.10.7 There shall be no attachment by cable tie fasteners,adhesives, or adhesive tapes.11. Workmanship, Finish, and Appearance11.1 There shall be no defects in materials or workmanshipthat will adversely affect the required performance of theinsulating cover.11.2 There shall b

39、e no defects that adversely affect theappearance of the insulating cover.12. Test Methods12.1 Apparent Material Thermal ConductivityDeterminein accordance with Test Method C177, in accordance withPractice C177 using the small temperature differences indi-cated in Practice C1045, Table 3. The test sp

40、ecimens shall beconditioned at 73 6 4F (23 6 2C) and 50 6 5 % relativehumidity for 24 6 1 hour prior to testing. The apparent thermalconductivity of the material for all specimens tested shall notaverage greater than the maximum value identified in Table 1.The apparent thermal conductivity of indivi

41、dual specimenstested shall not be greater than 120 % of the maximum valueidentified in Table 1.12.2 Water AbsorptionDetermine in accordance with TestMethod D570.12.3 Surface Burning CharacteristicsDetermine flamespread index and smoke developed index in accordance withTest Method E84.12.4 Rate of Bu

42、rningDetermine in accordance with TestMethod D635 using the HB (Horizontal Burning) orientation.Flame front shall not pass the 1 in. (25 mm) reference mark.TABLE 1 Insulating Cover Materials and Performance RequirementsNOTE 1This specification is used to measure and describe the response of material

43、s, products, or assemblies to heat and flame under controlledconditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies underthe actual fire conditions.NOTE 2The physical properties and performance requirement

44、s of this specification are determined at specific laboratory conditions and do not purportto address the performance at other conditions. It is the responsibility of the user to assure suitability of the material under field conditions.Property Type I Type II Type III Type IVApparent material therm

45、al conductivitymax #Btuin/hrft2F (W/m-K) at a mean temperatureof 75F (24C)1.3 (0.19) 1.3 (0.19) 1.3 (0.19) 1.3 (0.19)Material max calculatedthermal effusivity:Btu/ft2Fh12 (J/m2Ks12 )2.4 (820) 2.4 (820) 2.4 (820) 2.4 (820)Flame Spread Index #25 25 to #200 N/AAN/ASmoke Developed Index, max 450 450 N/A

46、 N/ARate of Burning, max,inch (mm)N/A N/A 1 (25) N/ADensity, max lb/ft3(kg/m3) 87 (1400) 87 (1400) 87 (1400) 87 (1400)Water Absorption, max,% by weight30 30 30 30Fungi Growth at four weeks, max 1 1 1 1Finished Product Min./Max.Surface Temperature F (C)68 (20)95 (35)Finished Product Exposure/Weathera

47、bility No cracking, checking, crazing, erosion, or chalking observed on the surface when observed at 5 magnifi-cation at 48 hoursFinished Product SurfaceDeflection and LoadNo signs of cracks or voids, after 5 minutes outside surface shall have no indentationsAN/A = not applicable.C1822 15312.5 Fungi

48、 GrowthDetermine in accordance with TestMethod G21. Specimen exterior surface shall have zero to onegrowth on surfaces at four weeks.12.6 Water temperature of 65F and pH maintained between6.0 and 8.0 pH.12.7 Surface Deflection and Load Test.12.8 No signs of cracks or voids; after five minutes outsid

49、esurface shall have no indentations.13. Product Marking13.1 Insulating cover shall be permanently marked or la-beled.13.2 Insulating cover shall be legibly marked as follows:13.2.1 The manufacturers name or trademark and address.13.2.2 Model number, Standard and Type.13.2.3 Country of Origin.13.2.4 Performance standard if required.14. Packaging and Package Marking14.1 Unless otherwise specified, the material shall be sup-plied in the manufacturers standard commercial package.14.2 MarkingUnless otherwise specified, each con