ASTM C1534-2007e1 Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems《用作管道系统吸热吸声衬垫的软质聚合物泡沫薄片的标准规范》.pdf

《ASTM C1534-2007e1 Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems《用作管道系统吸热吸声衬垫的软质聚合物泡沫薄片的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1534-2007e1 Standard Specification for Flexible Polymeric Foam Sheet Insulation Used as a Thermal and Sound Absorbing Liner for Duct Systems《用作管道系统吸热吸声衬垫的软质聚合物泡沫薄片的标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1534 071Standard Specification forFlexible Polymeric Foam Sheet Insulation Used as aThermal and Sound Absorbing Liner for Duct Systems1This standard is issued under the fixed designation C1534; the number immediately following the designation indicates the year oforiginal adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTESection 1.3 was editorially revised in April 2010.1. Scope1.1 This specification covers

3、the composition, dimensions,and physical properties of flexible unfaced foam sheet, used toinsulate interior surfaces of HVAC ducts, plenums and equip-ment used for the distribution of conditioned air with atemperature of up to 250F (121C).1.2 HVAC ducts, plenums and equipment systems typicallyopera

4、te between a temperature range of 50F to 150F (10C to65C) and are designed to meet building code requirements ofmaximum temperatures of 250F (121C).1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that ar

5、e provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applic

6、a-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2C168 Terminology Relating to Thermal InsulationC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC209 Test Methods for Cel

7、lulosic Fiber Insulating BoardC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC411 Test Method for Hot-Surface Performance of High-Temperature Thermal InsulationC423 Test Method for Sound Absorption and Sound Ab-sorption Coefficients by the Reverberation Room MethodC518 Test Metho

8、d for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusC634 Terminology Relating to Building and EnvironmentalAcousticsC665 Specification for Mineral-Fiber Blanket Thermal In-sulation for Light Frame Construction and ManufacturedHousingC1045 Practice for Calculati

9、ng Thermal Transmission Prop-erties Under Steady-State ConditionsC1071 Specification for Fibrous Glass Duct Lining Insula-tion (Thermal and Sound Absorbing Material)C1104/C1104M Test Method for Determining the WaterVapor Sorption of Unfaced Mineral Fiber InsulationC1114 Test Method for Steady-State

10、Thermal TransmissionProperties by Means of the Thin-Heater ApparatusC1304 Test Method for Assessing the Odor Emission ofThermal Insulation MaterialsC1338 Test Method for Determining Fungi Resistance ofInsulation Materials and FacingsE84 Test Method for Surface Burning Characteristics ofBuilding Mate

11、rialsE176 Terminology of Fire StandardsE795 Practices for Mounting Test Specimens During SoundAbsorption TestsE2231 Practice for Specimen Preparation and Mounting ofPipe and Duct Insulation Materials to Assess SurfaceBurning CharacteristicsG21 Practice for Determining Resistance of Synthetic Poly-me

12、ric Materials to Fungi2.2 Other Standards:CAN/ULC-S10203 Standard Method of Test for SurfaceBurning Characteristics of Building Materials and Assem-blies3. Terminology3.1 The definitions of terms used in this specification shallbe in accordance with Terminologies C168, C634, and E176.Incase of any c

13、onflicts, Terminology C168 shall be the authority.1This specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.22 onOrganic and Nonhomogeneous Inorganic Thermal Insulations.Current edition approved Sept. 1, 2007. Publis

14、hed September 2007. Originallyapproved in 2002. Last previous edition approved in 2004 as C153404. DOI:10.1520/C1534-07.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer

15、 to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2 Definitions of Terms Specific to This Standard:3.2.1 closed cell foama foam comprised of predominatelyindividual non inter

16、connecting cells.3.2.2 flexible cellulara cellular material that will notrupture within 60 s when a specimen 1 3 1 3 8 in. in length(25 3 25 3 200 mm) is bent around a 1 in. (25 mm) diametermandrel at a uniform rate of one lap in5sintheform of a helixat a temperature between 65 and 85F (18 and 29C).

17、3.2.3 open cell foama foam made porous by interconnect-ing cells.4. Classification4.1 The flexible polymeric insulations of this specificationare classified into Types I and II. Type I is a closed flexiblefoam. Type II is an open cell flexible foam.NOTE 1The primary difference between Type I and Typ

18、e II materialsare: Type I materials exhibit lower water absorption properties and TypeII materials have greater acoustical properties as noted in Tables 1 and 2.5. Materials5.1 These products shall be made of a homogeneous blendof natural or synthetic polymeric materials. Modifications withvarious t

19、hermoplastic or thermosetting resins, plasticizers,modifiers, antioxidants, curatives, blowing agents and otheradditives are allowed. These products do not melt whenexposed to heat and are considered to be thermoset materials.5.2 Flexible, polymeric cellular thermal insulations shall beof uniform co

20、re density. These insulation materials are avail-able with a smooth skin surface or coating on one or both sides,and they are to be considered homogeneous for the purposes ofdetermining thermal performance.6. Ordering Information6.1 Specific installation, insulation type, thickness, length,and width

21、 suited for the intended use shall be agreed upon bythe purchaser and supplier.7. Physical PropertiesSee Tables 1 and 2 for Summaryof Requirements7.1 Apparent Thermal ConductivityThe material shall betested for apparent thermal conductivity at 75F (24C) meantemperature in accordance with 12.1. The t

22、hermal conductivityfor the average of any four randomly selected samples, shallnot be more than 0.30 Btu-in./h-sq ftF (0.043 W/m-K) whentested in accordance with 12.1. See Table 1.NOTE 2Consult the local or state building codes for the minimuminstalled thermal resistance, R-value, required to be ins

23、talled.7.2 Surface Burning CharacteristicsShall be in accor-dance with 12.2. See Table 1 for requirements.7.3 Hot Surface PerformanceThe insulation shall have noevidence of flaming, glowing, smoldering, visible smoke,delamination, cracking, warpage, melting, dripping or reduc-tion in thickness when

24、tested in accordance with 12.3 at thetemperature specified in Table 1.NOTE 3Hot Surface Performance Characteristics for Type 1MaterialWhen this type of material is used on hot applications, thematerials characteristics will change and should be considered whenselecting the material for an applicatio

25、n. Heat will cause the elastomericinsulation to harden. As the temperature approaches the stated hightemperature limit, the process occurs faster. This hardening will notnegatively effect the thermal performance or water vapor transmissionproperties of the product. The hardening will be most noticea

26、ble closer tothe heat source. This effect is based on time and temperature.7.4 Water Vapor SorptionShall be tested in accordancewith 12.4. See Table 1.7.5 Water AbsorptionShall be tested in accordance with12.5. See Table 1.7.6 Dimensional StabilityShall be tested in accordancewith 12.6.7.7 Odor Emis

27、sionThere shall be no detectable odor ofobjectionable nature when tested in accordance with 12.7.7.8 CorrosivenessNo corrosion shall be noted whentested in accordance with 12.8.7.9 Fungi ResistanceWhen tested in accordance with12.9, the test specimens shall show no fungal growth.7.10 Erosion Resista

28、nceThe product shall show no evi-dence of delamination or continued erosion when air is passedthrough typical duct sections when tested in accordance with12.10.7.11 Sound Absorption CoeffcientWhen tested in accor-dance with Test Method C423 using an “A” mounting inTABLE 1 Physical PropertiesType I T

29、ype IIMaximum Apparent Thermal Conductivity Btu-in./h-ft2F) max.(W/m-K) max.0.30(0.043)0.30(0.043)Surface Burning Characteristics ( at maximum total installedthickness):(SeeA) (SeeA)Flame Spread Index, (max) # 25 15Smoke Developed Index, (max) # 50 15Water Vapor Sorption wt % gain by vol. (max.) 0.0

30、0 0.1Water Absorption, wt % gain by vol. (max.) 0.2 4.0Dimensional Stability % change (max.) length, width or thickness 7.0 1.0Odor Emission Pass PassCorrosiveness Pass PassFungi Resistance No Growth No GrowthErosion Resistance Pass PassHot Surface Performance at not less than 250F (125C)(See 7.3 fo

31、r requirements)Pass PassBAConsult manufacturer regarding maximum thickness approved for surface burning characteristics Type 1 is typically tested at 1 in. thickness. Type 2 is typically testedat 2 in. thickness. Product should be tested at the thickness to be used in the application.BActual product

32、 properties may exceed requirements listed in Table 1, consult manufacturers for specific applications.C1534 0712accordance with Practice E795, the insulation shall have soundabsorption coefficient and NRC not less than that indicated inTable 2.8. Qualification and Inspection Requirements8.1 Qualifi

33、cation RequirementsThe following require-ments shall be used for purposes of initial material qualifica-tion:8.1.1 Apparent thermal conductivity,8.1.2 Surface burning characteristics,8.1.3 Hot surface performance,8.1.4 Water vapor sorption,8.1.5 Water absorption,8.1.6 Odor emission,8.1.7 Corrosivene

34、ss,8.1.8 Fungi resistance,8.1.9 Erosion resistance, and8.1.10 Sound absorption coefficient.8.2 InspectionThe following requirements shall be usedfor purposes of acceptance sampling of lots or shipments ofqualified thermal insulation:8.2.1 Dimensional tolerances, and8.2.2 Workmanship.9. Dimensional T

35、olerances9.1 After conditioning for a minimum of 24 h at 70 6 3F(21 6 1.6C) and 50 6 5 % relative humidity, the insulationshall conform to the dimensional tolerances listed in Table 3.All dimensions shall be measured at the conditioning tempera-ture.10. Workmanship and Finish10.1 The insulation shal

36、l indicate good workmanship infabrication and shall not have visible defects that adverselyeffect service performance.11. Sampling11.1 Sampling of the insulation shall be in accordance withPractice C390. Specific provisions for sampling shall be agreedupon between the purchaser and the supplier.12.

37、Test Methods12.1 Apparent Thermal ConductivityTest in accordancewith Test Method C177 or Test Method C518 or Test MethodC1114 at 75F (24C) mean temperature (see also PracticeC1045).12.2 Surface Burning CharacteristicsDetermine the sur-face burning characteristic for the material in accordance withTe

38、st Method E84. In Canada use Test Method CAN/ULC-S10203. The results shall be reported. See Section 1 of TestMethod E84 for information regarding the applicability of thistest method for use with cellular plastics and Practice E2231for specimen mounting methods.12.3 Hot Service PerformanceThe maximu

39、m hot surfacetemperature of the material shall be tested in accordance withTest Method C411.12.4 Water Vapor SorptionTest the water sorption of thematerial in accordance with the Test Method C1104/C1104M.12.5 Water AbsorptionDetermine the amount of waterabsorption of the test specimen in accordance

40、with TestMethod C209 (24 h immersion time).12.6 Dimensional StabilityDetermine length, width andthickness change when tested in accordance with C356 afteraging 24 h at a minimum of 250F (125C) or the maximumuse temperature whichever is higher.12.7 Odor EmissionDetermine the odor emission in ac-corda

41、nce with Test Method C1304 except test at 200F (92C).12.8 CorrosivenessThe corrosiveness of the material shallbe determined in accordance with the corrosiveness testmethod defined in Specification C665.12.9 Fungi/ResistanceThe fungi resistance of the materialshall be determined in accordance with Pr

42、actice G21 and TestMethod C1338.12.10 Erosion ResistanceThe air erosion properties of thematerial shall be as determined in accordance with the erosionresistance test methods and requirements defined in Specifica-tion C1071. The air velocity for the test is dependent upon theuse of the product. The

43、air velocity for the test shall be 2.5times the maximum rated velocity of the product.12.11 Sound Absorption CoeffcientTest in accordancewith Test Method C423 using an “A” mounting in accordancewith Practice E795.13. Inspection13.1 Inspection of the insulation shall be as agreed upon bythe purchaser

44、 and the manufacturer as part of the purchaseagreement.TABLE 2 Sound Absorption Coefficients (min) Using Test Method C423 Type “A” MountingAPractice E795.Frequency, Hz 125 250 500 1000 2000 4000 NRCAType I12 in. (13 mm) 0.03 0.04 0.06 0.20 0.40 0.15 0.201 in. (25 mm) 0.15 0.10 0.30 0.30 0.20 0.20 0.

45、25Type II12 in. (13 mm) 0.07 0.10 0.25 0.60 0.98 0.85 0.501 in. (25 mm) 0.14 0.20 0.45 0.80 0.98 0.85 0.602 in. (50 mm) 0.25 0.58 1.00 0.98 1.00 0.90 0.90ANRC-Noise Reduction CoefficientTABLE 3 Dimensional Tolerance, in. (mm)Dimension ToleranceWidth +0.250 in./-0 in. (+6 mm/-0 mm)Length -0/excess pe

46、rmittedThickness 610 %C1534 071314. Rejection14.1 Material that fails to conform to the requirementsagreed upon in the purchasing agreement is subject to rejec-tion. Rejection shall be reported to the producer or supplierpromptly and in writing.15. Certification15.1 When specified in the purchase or

47、der or contract, aproducers, suppliers, or independent third partys certificationshall be furnished to the purchaser indicating that the materialwas manufactured, sampled, tested, and inspected in accor-dance with this specification and has been found to meet therequirements. When specified in the p

48、urchase order or contract,a report of test results shall be furnished.16. Product Marking16.1 The air stream surface of the liner shall be markedaccording to the purchasers requirements, for example: prod-uct name, thickness, manufacturer, surface burning character-istics and nominal R-value.17. Pac

49、kaging and Package Marking17.1 PackagingUnless otherwise specified, the insulationshall be packaged in the manufacturers standard containers.17.2 Package MarkingThe markings shall be clear andlegible. The package shall be marked with the manufacturersname, address, product name, lot number, material width,length, thickness, and nominal R-value.18. Keywords18.1 closed cell; ducts; flexible; foam; HVAC; insulation;open cell; sound absorbing; thermal insulationASTM International takes no position respecting t