ASTM C1244-2011 Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填前使用负气压(真空)测试混凝土排水管检修孔的标准试验方法》.pdf

《ASTM C1244-2011 Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填前使用负气压(真空)测试混凝土排水管检修孔的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1244-2011 Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill《回填前使用负气压(真空)测试混凝土排水管检修孔的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1244 11Standard Test Method forConcrete Sewer Manholes by the Negative Air Pressure(Vacuum) Test Prior to Backfill1This standard is issued under the fixed designation C1244; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revis

2、ion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers procedures for testing precastconcrete manhole sections when using the vacuum

3、 test methodto demonstrate the integrity of the installed materials and theconstruction procedures. This test method is used for testingconcrete manhole sections utilizing mortar, mastic, or gasketedjoints.1.2 This test method is intended to be used as a preliminarytest to enable the installer to de

4、monstrate the condition of theconcrete manholes prior to backfill. Users are hereby cautionedthat misuse or misapplication of the test criteria containedherein can cause permanent damage to the system being tested.NOTE 1Vacuum test criteria presented in this test method are similarto those in genera

5、l use. The test and criteria have been widely andsuccessfully used in testing manholes.NOTE 2The user of this test method is advised that no correlation hasbeen found between vacuum (air) and hydrostatic tests.1.3 This test method is the companion to metric TestMethod C1244M; therefore, no SI equiva

6、lents are shown inthis test method.1.4 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limit

7、ations prior to use.2. Referenced Documents2.1 ASTM Standards:2C822 Terminology Relating to Concrete Pipe and RelatedProductsC924 Practice for Testing Concrete Pipe Sewer Lines byLow-Pressure Air Test MethodC969 Practice for Infiltration and Exfiltration AcceptanceTesting of Installed Precast Concre

8、te Pipe Sewer LinesC1244M Test Method for Concrete Sewer Manholes by theNegative Air Pressure (Vacuum) Test Prior to Backfill(Metric)3. Terminology3.1 For definitions of terms relating to manholes, seeTerminology C822.4. Summary of Practice4.1 All lift holes and any pipes entering the manhole are to

9、be plugged.Avacuum will be drawn and the vacuum drop overa specified time period is used to determine the acceptability ofthe manhole.5. Significance and Use5.1 This is not a routine test. The values recorded areapplicable only to the manhole being tested and at the time oftesting.6. Preparation of

10、the Manhole6.1 All lift holes shall be plugged.6.2 All pipes entering the manhole shall be temporarilyplugged, taking care to securely brace the pipes and plugs toprevent them from being drawn into the manhole.7. Procedure7.1 The test head shall be placed at the top of the manholein accordance with

11、the manufacturers recommendations.7.2 A vacuum of 10 in. Hg shall be drawn on the manhole,the valve on the vacuum line of the test head closed, and thevacuum pump shut off. The time shall be measured for thevacuum to drop to 9 in. Hg.1This test method is under the jurisdiction of ASTM Committee C13

12、onManholes and Specials.Current edition approved Nov. 1, 2011. Published November 2011. Originallyapproved in 1993. Last previous edition approved in 2005 as C1244 05a1. DOI:10.1520/C1244-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serv

13、iceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.3 The manhole is acceptable if the time for the vacuu

14、mreading to drop from 10 in. Hg to 9 in. Hg meets or exceeds thevalues indicated in Table 1.7.4 If the manhole fails the initial test, the manhole shall berepaired by an approved method until a satisfactory test isobtained.7.5 Use or failure of this vacuum test shall not precludeacceptance by approp

15、riate water infiltration or exfiltrationtesting, (see Practice C969), or other means.8. Precision and Bias8.1 No justifiable statement is presently capable of beingmade either on the precision or bias of this procedure, since thetest result merely states whether there is conformance to thecriteria f

16、or the success specified.9. Keywords9.1 acceptance criteria; concrete; manhole sections; testmethod; vacuum testAPPENDIX(Nonmandatory Information)X1. Air Testing for a Single Diameter PipeX1.1 The standard accepted method of air testing, for asingle diameter pipe, Practice C924, allows a drop of 1 p

17、sipressure during the time calculated by the formula:TPress.5KD2LQ(X1.1)where:T = time for 1 psi drop in pressureK = 0.00037 for in./lb unitsD = pipe diameter, in.L = length of line, ftQ = air loss, ft3/minX1.2 A pressure drop of 1 in. Hg for the vacuum testcompares to a pressure drop of 0.490 psi f

18、or the air test.1 in. Hg 314.696 lb/in.229.02 1 Hg5 0.490 psi (X1.2)Therefore, the time relationship is:Tvac5 0.490 Tpress(X1.3)orTvac5Tpress2.04(X1.4)X1.3 The allowable test times cited in Practice C924,Table 2, for pipe sizes 4 in. to 24 in. diameter are provided inTable X1.1 and Table X1.2. The a

19、llowable test times for sizesabove 24 in. were obtained by extrapolation. Therefore, usingthe appropriate Q. we find that:TABLE 1 Minimum Test Times for Various Manhole Diameters(30 120 in.) in SecondsDepth (ft)Diameter, in.30 33 36 42 48 54 60 66 72Time, in seconds4 6 7 7 9 10 12 13 15 166 9 10 11

20、13 15 18 20 22 258111241720232629310 14 15 18 21 25 29 33 36 4112 17 18 21 25 30 35 39 43 4914 20 21 25 30 35 41 46 51 5716 22 24 29 34 40 46 52 58 6718 25 27 32 38 45 52 59 65 7320 28 30 35 42 50 53 65 72 8122 31 33 39 46 55 64 72 79 8924 33 36 42 51 59 64 78 87 9726 36 39 46 55 64 75 85 94 10528 3

21、9 42 49 59 69 81 91 101 11330 42 45 53 63 74 87 98 108 121TABLE 1 Minimum Test Times for Various Manhole Diameters(30 120 in.) in Seconds (continued)Depth (ft)Diameter, in.78 84 90 96 102 108 114 120Time, in seconds4 18 19 21 23 24 25 27 296 26293134363841438 353841454851545710 44 48 52 56 60 63 67

22、7112 53 57 62 67 71 76 81 8514 62 67 72 78 83 89 94 10016 70 76 83 89 95 101 108 11418 79 86 93 100 107 114 121 12820 88 95 103 111 119 126 135 14222 97 105 114 122 131 139 148 15624 106 114 124 133 143 152 161 17026 114 124 134 144 155 164 175 18528 123 133 145 155 167 177 188 19930 132 143 155 166

23、 178 189 202 213C1244 112for 30 in. Q 5 7ft3/min!, Tvac5 0.00018D2QL 5 0.023 Lfor 36 in. Q 5 8ft3/min!, Tvac5 0.00018D2QL 5 0.029 Lfor 42 in. Q 5 9ft3/min!, Tvac5 0.00018D2QL 5 0.035 Lfor 48 in. Q 5 10 ft3/min!, Tvac5 0.00018D2QL 5 0.041 Lfor 54 in. Q 5 11 ft3/min!, Tvac5 0.00018D2QL 5 0.048 Lfor 60

24、 in. Q 5 12 ft3/min!, Tvac5 0.00018D2QL 5 0.054 Lfor 66 in. Q 5 13 ft3/min!, Tvac5 0.00018D2QL 5 0.060 Lfor 72 in. Q 5 14 ft3/min!, Tvac5 0.00018D2QL 5 0.067 Lfor 78 in. Q 5 15 ft3/min!, Tvac5 0.00018D2QL 5 0.073 Lfor 84 in. Q 5 16 ft3/min!, Tvac5 0.00018D2QL 5 0.079 Lfor 90 in. Q 5 17 ft3/min!, Tva

25、c5 0.00018D2QL 5 0.086 Lfor 96 in. Q 5 18 ft3/min!, Tvac5 0.00018D2QL 5 0.092 Lfor 102 in. Q 5 19 ft3/min!, Tvac5 0.00018D2QL 5 0.099 Lfor 108 in. Q 5 20 ft3/min!, Tvac5 0.00018D2QL 5 0.105 Lfor 114 in. Q 5 21 ft3/min!, Tvac5 0.00018D2QL 5 0.112 Lfor 120 in. Q 5 22 ft3/min!, Tvac5 0.00018D2QL 5 0.11

26、8 LC1244 113ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such

27、 rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additi

28、onal standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the

29、ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the a

30、boveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE X1.1 Minimum Test Times for Various Pipe Diameters

31、(Practice C924)Nominal Pipe Size, in. Time (T), min 100 ft.40.360781210 1.512 1.815 2.118 2.421 3.024 3.627 4.230 4.833 5.436 6.0TABLE X1.2 Allowable Air Loss for Various Pipe Diameters(Practice C924)Nominal Pipe Size, in. Air Loss (Q), ft3/min42628210 2.512 315 418 521 5.524 630 736 842 948 1054 1160 1266 1372 14C1244 114