ASTM C1093-2013ae1 Standard Practice for Accreditation of Testing Agencies for Masonry《石工行业检测机构认证的标准实施规程》.pdf
《ASTM C1093-2013ae1 Standard Practice for Accreditation of Testing Agencies for Masonry《石工行业检测机构认证的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1093-2013ae1 Standard Practice for Accreditation of Testing Agencies for Masonry《石工行业检测机构认证的标准实施规程》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1093 13a1Standard Practice forAccreditation of Testing Agencies for Masonry1This standard is issued under the fixed designation C1093; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe
2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially corrected 7.1.1, 8.5.2.8, and 8.5.2.9 in February 2014.1. Scope*1.1 This practice covers the minimum requirements forlaboratory personn
3、el, for establishing and maintaining a qualitysystem, and it establishes minimum qualifications for agenciesengaged in the testing of masonry materials.1.2 Criteria are provided for evaluating the capability of anagency to properly perform designated tests on masonrymaterials, and for establishing g
4、uidelines pertaining to anagencys organization, personnel, facilities, and quality system.This practice may be supplemented by more specific criteriaand requirements for particular projects.1.3 This practice can be used as a basis to evaluate testingagencies, and it is intended for use for the quali
5、fying oraccrediting of testing agencies, or both, public or private,engaged in the testing of masonry materials.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate saf
6、ety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C67 Test Methods for Sampling and Testing Brick andStructural Clay TileC109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in. o
7、r 50-mm CubeSpecimens)C117 Test Method for Materials Finer than 75-m (No. 200)Sieve in Mineral Aggregates by WashingC136 Test Method for Sieve Analysis of Fine and CoarseAggregatesC140 Test Methods for Sampling and Testing ConcreteMasonry Units and Related UnitsC143/C143M Test Method for Slump of Hy
8、draulic-CementConcreteC173/C173M Test Method forAir Content of Freshly MixedConcrete by the Volumetric MethodC185 Test Method for Air Content of Hydraulic CementMortarC230/C230M Specification for Flow Table for Use in Testsof Hydraulic CementC231 Test Method for Air Content of Freshly Mixed Con-cret
9、e by the Pressure MethodC270 Specification for Mortar for Unit MasonryC305 Practice for Mechanical Mixing of Hydraulic CementPastes and Mortars of Plastic ConsistencyC470/C470M Specification for Molds for Forming ConcreteTest Cylinders VerticallyC780 Test Method for Preconstruction and ConstructionE
10、valuation of Mortars for Plain and Reinforced UnitMasonryC1072 Test Methods for Measurement of Masonry FlexuralBond StrengthC1232 Terminology of MasonryC1506 Test Method for Water Retention of HydraulicCement-Based Mortars and PlastersE4 Practices for Force Verification of Testing MachinesE11 Specif
11、ication for Woven Wire Test Sieve Cloth and TestSieves3. Terminology3.1 Definitions:3.1.1 quality systemthe organizational structure,responsibilities, procedures, processes, capabilities, and re-sources for implementing quality management.3.2 Definitions of Terms Specific to This Standard:3.2.1 agen
12、cythe organization engaged to test masonrymaterials as required by a specification or contract.3.2.2 quality system manual (QSM)a manual describingand documenting an agencys quality system.1This practice is under the jurisdiction of ASTM Committee C15 on Manufac-tured Masonry Units and is the direct
13、 responsibility of Subcommittee C15.07 onStandards for Laboratory Accreditation.Current edition approved Dec. 15, 2013. Published January 2014. Originallyapproved in 1988. Last previous edition approved in 2013 as C1093 13. DOI:10.1520/C1093-13A.2For referenced ASTM standards, visit the ASTM website
14、, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Driv
15、e, PO Box C700, West Conshohocken, PA 19428-2959. United States13.2.3 userthe person or organization engaging the agencyto provide tests; or using this practice to evaluate or accreditthe agency.3.3 For additional terms used in this standard, refer toTerminology C1232.4. Significance and Use4.1 This
16、 practice provides the basic minimum criteria foruse in evaluating the qualifications of testing agencies formasonry materials. The criteria may be supplemented by morespecific criteria and requirements. It can be used as a guide forinternal audits by individual users.4.2 The intent of this practice
17、 is to provide a consensus basisfor evaluating a testing agency, with respect to that agencyscapability to objectively and competently provide the specificservices needed by the user.4.3 This practice may be used as a basis for accreditation.5. Responsibilities and Duties5.1 The agency shall ensure
18、that only tests for which it isadequately equipped and staffed are performed.5.2 The agency shall ensure that personnel perform onlytests for which they are adequately trained, qualified, andcertified in accordance with applicable specifications.5.3 The agency shall ensure that all equipment is prop
19、erlymaintained in good operating condition and is calibrated orverified as applicable.5.4 The agency shall perform all testing in accordance withappropriate standards and quality control criteria. Documentsunique to the user shall be furnished to the agency.6. General Capabilities6.1 Laboratory Test
20、ingThe laboratory testing services ofthe masonry materials testing agency shall include some or allof the following capabilities:6.1.1 Testing of masonry units in the laboratory,6.1.2 Testing of masonry mortars in the laboratory, and6.1.3 Testing of aggregates for compliance with specifica-tion requ
21、irements.NOTE 1Since the requirements for construction control can vary fromproject to project depending upon the nature of the type, location, andintended use of the masonry in the project, the capability of the agency fortesting should be that necessary to accomplish construction control for theus
22、ers specific project or special requirements.7. Personnel Qualifications7.1 Management and SupervisionAll relevant testing ser-vices shall be provided under the Full-Time technical directionof a registered professional Engineer, with at least 5 years ofexperience in inspecting and testing masonry ma
23、terials or aperson of equivalent science-oriented education and experi-ence.7.1.1 It is satisfactory for a person to fill one or more of thelevels of management in an agency, Manager, Supervisor, orTechnician positions in accordance with 7 and 7.2 providingthat person is qualified for each position.
24、7.2 Supervising Laboratory TechnicianThe supervisinglaboratory technician shall have at least five years experienceperforming tests on materials, with at least two years testingmasonry materials. This person shall be able to demonstrate,either by oral or written examination, or both, the ability top
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC10932013AE1STANDARDPRACTICEFORACCREDITATIONOFTESTINGAGENCIESFORMASONRY 石工 行业 检测 机构 认证 标准 实施 规程 PDF

链接地址:http://www.mydoc123.com/p-463343.html