ASTM B914-2003(2008) Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel《钢热浸镀锌用锌和锌合金铸锭颜色编码的标准实施规程》.pdf

《ASTM B914-2003(2008) Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel《钢热浸镀锌用锌和锌合金铸锭颜色编码的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM B914-2003(2008) Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel《钢热浸镀锌用锌和锌合金铸锭颜色编码的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 914 03 (Reapproved 2008)Standard Practice forColor Codes on Zinc and Zinc Alloy Ingot for Use in Hot-DipGalvanizing of Steel1This standard is issued under the fixed designation B 914; the number immediately following the designation indicates the year oforiginal adoption or, in the ca

2、se of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This standard is published with the following objectives:1.1.1 To establish standard colo

3、r codes for zinc, zinc alloyand zinc master alloy ingot used by the Hot-Dip Galvanizingindustry, and1.1.2 To standardize the use and application of these colorcodes.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of th

4、e user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limita

5、tions prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B6 Specification for ZincB 275 Practice for Codification of Certain Nonferrous Met-als and Allo

6、ys, Cast and WroughtB 750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip CoatingsB 852 Specification for Continuous Galvanizing Grade(CGG) ZincAlloys for Hot-Dip Galvanizing of Sheet SteelB 860 Specification for Zinc Master Alloys for Use in HotDip Galvanizin

7、gB 899 Terminology Relating to Non-ferrous Metals andAlloysE 527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.3 ISO Standard:ISO 752 Zinc and Zinc AlloysPrimary Zinc32.4 CEN Standard:EN 1179 Zinc and Zinc AlloysPrimary Zinc43. Terminology3.1 Terms shall be defined i

8、n accordance with TerminologyB 899.4. Significance and Use4.1 The purpose of these color codes is to allow for quickidentification of ingot bundles or jumbo ingots of alloys usedfor hot-dip galvanizing. Other than jumbo ingots, this standardis not intended to imply that each ingot will be color-code

9、d butonly that each ingot bundle be color coded.4.2 Each ingot bundle or jumbo ingot shall be identifiedwith the appropriate color code listed in Table 1.4.3 The color will be applied as a stripe, or stripes, on twoadjacent sides of the ingot bundle or jumbo ingot. The colorstripes will be applied t

10、o include the ingot bundle foot.4.4 When using multiple stripes, the colored stripes will beapplied from left to right as indicated in Table 1.4.5 In the absence of a written agreement to the contrarybetween the supplier and end user, the North American colorcode will be the standard for all North A

11、merican transactions;for all other transactions the International Color Code will beused.5. Keywords5.1 aluminum-zinc alloys; color; color code; GALFAN;GALVALUME; galvanizing; hot-dip; non-ferrous metals; zinc;zinc alloys; zinc-aluminum alloys1This practice is under the jurisdiction of ASTM Committe

12、e B02 on NonferrousMetals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zincand Cadmium.Current edition approved May 1, 2008. Published May 2008. Originallyapproved in 2000. Last previous edition approved in 2003 as B 914 - 03e2.2For referenced ASTM standards, visit the ASTM

13、website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036,

14、http:/www.ansi.org.4Available from Global Engineering Documents, 15 Inverness Way, EastEnglewood, CO 80112-5704, http:/.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of a

15、ny patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to re

16、vision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. You

17、r comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copy

18、righted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.or

19、g (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Color Codes for Zinc and Zinc Alloys Used for Hot Dip GalvanizingAlloy UNSAASTMStandardNominal Composition Color CodeAl Other North AmericaBInternationalPrimary Zinc GradesCSHG (Z13001) B6 Yellow YellowHG (Z15001) B6 Green GreenPW (Z19001

20、) B6 Pb1.0 % Black BlackCGG Alloys(Z80310) B 852 0.25 Brown/Brown Yellow/Brown(Z80411) B 852 0.35 Blue/Blue Yellow/Blue(Z80511) B 852 0.45 Purple/Purple Yellow/Purple(Z80531) B 852 0.45 Pb0.02 % Red/Red Yellow/Red(Z80610) B 852 0.55 Pink/Pink Yellow/Pink(Z80710) B 852 0.65 Green/Green Yellow/Green(Z

21、80810) B 852 0.75 Black/Black Yellow/Black(Z80910) B 852 1.00 Orange/Orange Yellow/OrangeMaster AlloysType A-1 (Z30750) B 860 10.0 High Purity Red/Green Yellow/Red/GreenType A-2 (Z31710) B 860 10.0 Low Purity Red/Black Yellow/Red/BlackType A-3 (Z30503) B 860 5.0 High Purity Red/Blue Yellow/Red/BlueT

22、ype A-4 (Z31510) B 860 5.0 Low Purity Red/Yellow Yellow/Red/YellowType S-1 (Z55710) B 860 Sb10.0 % Black/Green Yellow/Black/GreenSpecialty AlloysGALFAND(Z38510) B 750 5.0 Mischmetal Purple/Blue Yellow/Purple/BlueGALVALUMEE55.0 Si1.5 % Orange/Green Yellow/Orange/GreenAUNS assignations were establishe

23、d in accordance with Practice E 527. The last digit of a UNS number differentiates between alloys of similar composition.BThe North American system is designed to be a simplified version of the International system by eliminating the leading yellow stripe.CColor codes taken from European Standard EN 1179.DGALFAN is a registered trademark of the GALFAN Information Center, Inc.EGALVALUME is a registered trademark of BIEC International Inc., USA.B 914 03 (2008)2