ASTM B701 B701M-2013 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规格》.pdf

《ASTM B701 B701M-2013 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B701 B701M-2013 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规格》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B701/B701M 06B701/B701M 13Standard Specification forConcentric-Lay-Stranded Self-Damping AluminumConductors, Steel Reinforced (ACSR/SD)1This standard is issued under the fixed designation B701/B701M; the number immediately following the designation indicates the yearof original adoption

2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers concentric-lay-stranded self-damping aluminum cond

3、uctor, steel-reinforced (ACSR/SD), and itscomponent wires for use as overhead electrical conductors (Explanatory Notes 1 and 2).1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. Each system shall be usedindependently of the other. Combining values from the tw

4、o systems may result in non-conformance with the specification. Forconductor sizes designated by AWG or kcmil, the requirements in SI units have been numerically converted from correspondingvalues stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirement

5、s are stated or derivedin SI units.1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.NOTE 1ACSR/SD is designed to control aeolian vibration by integral damping. The conductors consist of a central core of a round steel wire or wiressurround

6、ed by two layers of trapezoidal aluminum 1350-H19 wires or two layers of trapezoidal aluminum 1350-H19 wires and one layer of roundaluminum 1350-H19 wires (Fig. 1). The trapezoidal-wire layers are separated from each other and from the steel core by two small annular gaps thatprovide the conductors

7、self-damping characteristics. The round aluminum wires are in tight layer contact between themselves and the underlyingtrapezoidal wire layer. Different strandings of the same size of conductor are identified by type, which is the approximate ratio of steel area to aluminumarea, expressed in percent

8、 (Table 1 and Table 2).NOTE 2The aluminum and temper designations conform toANSI Standard H 35.1.Aluminum 1350 corresponds to UNSA91350 in accordance withPractice E527.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityo

9、f the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the exten

10、treferenced herein.2.2 ASTM Standards:2B230/B230M Specification for Aluminum 1350H19 Wire for Electrical PurposesB232/B232M Specification for Concentric-Lay-Stranded Aluminum Conductors, Coated-Steel Reinforced (ACSR)B263 Test Method for Determination of Cross-Sectional Area of Stranded ConductorsB3

11、41/B341M Specification for Aluminum-Coated (Aluminized) Steel Core Wire for Aluminum Conductors, Steel Reinforced(ACSR/AZ) (Withdrawn 2007)3B354 Terminology Relating to Uninsulated Metallic Electrical ConductorsB498/B498M Specification for Zinc-Coated (Galvanized) Steel Core Wire for Use in Overhead

12、 Electrical ConductorsB500/B500M Specification for Metallic Coated or Aluminum Clad Stranded Steel Core for Use in Overhead ElectricalConductorsB502 Specification for Aluminum-Clad Steel Core Wire for Use in Overhead Electrical Aluminum ConductorsB549 Specification for Concentric-Lay-StrandedAluminu

13、m Conductors,Aluminum-Clad Steel Reinforced for Use in OverheadElectrical Conductors1 This specification is under the jurisdiction of ASTM Committee B01 on Electrical Conductors and is the direct responsibility of Subcommittee B01.07 on Conductorsof Light Metals.Current edition approved March 1, 200

14、6May 1, 2013. Published March 2006June 2013. Originally approved in 1981. Last previous edition approved in 20002006 asB701/B701M 00. 06. DOI: 10.1520/B0701_B0701M-06.10.1520/B0701_B0701M-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at servi

15、ceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. B

16、ecauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 10

17、0 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1B606 Specification for High-Strength Zinc-Coated (Galvanized) Steel Core Wire for Aluminum and Aluminum-AlloyConductors, Steel ReinforcedB802/B802M Specification for Zinc5 % Aluminum-Mischmetal Alloy-Coated Steel Core

18、Wire for Aluminum Conductors,Steel Reinforced (ACSR)B803 Specification for High-Strength Zinc5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use in OverheadElectrical ConductorsE29 Practice for Using Significant Digits in Test Data to Determine Conformance with SpecificationsE527 Practice f

19、or Numbering Metals and Alloys in the Unified Numbering System (UNS)2.3 ANSI Documents:3ANSI H35.1 American National Standard Alloy and Temper Designation Systems for Aluminum2.4 NIST Documents:4NBS Handbook 100 Copper Wire Tables of the National Bureau of Standards2.5 Aluminum Association Documents

20、:5Publication 50, Code Words for Overhead Aluminum Electrical Conductors3. Terminology3.1 Abbreviations:Definitions of Terms Specific to This Standard:3.1.1 ACSR/SD covered by this specification has five types of coated core wire and one type of aluminum-clad core wire whichare designated by abbrevi

21、ations as follows (Explanatory Note 2Notes 2 and 10):3.1.2 ACSR/SD/AWACSR/SD/AW2ACSR/SD using aluminum-clad steel wire (Specification B502).3.1.3 ACSR/SD/AZACSR/SD using aluminum-coated (aluminized) steel wire (Specification B341/B341M).3.1.3 ACSR/SD/GAACSR/SD/GA2ACSR/SD using Class A zinc-coated st

22、eel wire (Specification B498/B498M).3.1.4 ACSR/SD/GBACSR/SD/GC2ACSR/SD using Class BC zinc-coated steel wire (Specification B498/B498M).3.1.6 ACSR/SD/GCACSR/SD using Class C zinc-coated steel wire (Specification B498/B498M).3.1.5 ACSR/SD/HSACSR/SDACSR/SD using extra highstrengthhigh-strength steel w

23、ire (Specification B606).3.1.6 ACSR/SD/MAACSR/SD/MA2ACSR/SD using Class A zinc-5 % aluminum-mischmetal alloy-coated steel core wire(Specification B802/B802M).3.1.7 ACSR/SD/MBACSR/SD/MB2ACSR/SD using Class B zinc-5 % aluminum-mischmetal alloy-coated steel core wire(Specification B802/B802M).3.1.8 ACS

24、R/SD/MCACSR/SD/MC2ACSR/SD using Class V zinc-5 % aluminum-mischmetal alloy-coated steel core wire(Specification B802/B802M).3.1.9 ACSR/SD/MSACSR/SDACSR/SD using high-strength zinc-5 % Aluminum-mischmetal alloy-coated steel core wire(Specification B803).3.2 For definitions of terms relating to conduc

25、tors, refer to Terminology Standard B354.3 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.10036, http:/www.ansi.org.4 Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 3460,1070, Gaithersburg, MD 208

26、99-3460.20899-1070, http:/www.nist.gov.5 Available from Aluminum Association Inc., 900 19th Street, NW, Suite 300, Washington, DC 20006.Association, Inc., 1525 Wilson Blvd., Suite 600, Arlington, VA22209, http:/www.aluminum.org.FIG. 1 Illustrations of Typical ACSR/SD StrandingsB701/B701M 132TABLE 1

27、Construction Requirements of Aluminum Conductors, Self Damping, Concentric-Lay-Stranded, Steel-ReinforcedStranding Number of Wires and Diameter, in.A NominalAlumi-numLayFactorMass per1000 ft, lbRatedStrength,kipA,BNominalOutsideDiameter,in.Conductor Size Aluminum SteelCkcmil TypeD Code WordE Round T

28、rapezoidalF Round2156 8 Bluebird21 0.214510 0.217915 0.218419 0.0961 14.512.111.02504 60.7 1.7161780 8 Chukar21 0.19579 0.204113 0.215019 0.0874 14.512.011.02068 51.1 1.5651780 5 Smew21 0.19148 0.217114 0.21287 0.1144 16.012.511.51921 43.6 1.5311590 13 Falcon24 0.169010 0.189114 0.197719 0.1030 13.5

29、11.711.52039 55.1 1.5211590 7 Lapwing21 0.18358 0.205912 0.21307 0.1253 15.912.811.51791 42.6 1.4681590 5 Ratite23 0.16698 0.209513 0.21437 0.1083 15.412.511.51715 39.1 1.4471431 13 Plover24 0.160910 0.179214 0.186819 0.0977 13.511.711.51835 49.6 1.4481431 7 Bobolink21 0.17478 0.194612 0.20157 0.118

30、9 15.112.211.51612 38.9 1.3981431 5 Popinjay21 0.17268 0.193613 0.19727 0.1025 16.012.511.51544 35.3 1.3811351.5 13 Martin21 0.177211 0.160415 0.165219 0.0949 14.712.811.51733 46.8 1.4171351.5 10 Frigate21 0.17359 0.178614 0.17577 0.1377 14.512.211.01629 41.7 1.3891351.5 7 Dipper21 0.17018 0.189012

31、0.19547 0.1155 15.212.211.01522 36.7 1.3611351.5 5 Ringdove21 0.16808 0.194612 0.19497 0.0997 16.012.811.51458 33.4 1.3441272 13 Pheasant21 0.172311 0.155215 0.159919 0.0921 14.712.811.51631 44.1 1.3781272 7 Bittern21 0.16538 0.182912 0.18947 0.1121 14.512.311.51433 34.6 1.3231272 5 Scissortail21 0.

32、16317 0.192911 0.20297 0.0967 15.712.311.51372 31.4 1.3051192.5 13 Grackle 10 0.2147 19 0.0892 14.2 1526 41.9 1.27416 0.2138 11.51192.5 7 Bunting 8 0.1768 7 0.1085 15.1 1343 32.4 1.28412 0.1831 12.221 0.1604 11.51192.5 5 Oxbird21 0.15827 0.186811 0.19607 0.0936 15.712.311.51286 29.5 1.2661113 13 Fin

33、ch 9 0.2188 19 0.0862 14.2 1424 39.1 1.23315 0.2133 11.51113 7 Bluejay 8 0.1705 7 0.1049 15.9 1254 30.3 1.24212 0.1765 12.821 0.1553 11.51113 5 Avocet21 0.15337 0.181812 0.17987 0.0904 16.012.411.51200 27.5 1.2261033.5 13 Curlew 9 0.210614 0.21297 0.1383 14.211.51329 36.3 1.1911033.5 7 Ortolan 8 0.2

34、16814 0.21677 0.1010 15.211.51161 28.1 1.145B701/B701M 133TABLE 1 ContinuedStranding Number of Wires and Diameter, in.A NominalAlumi-numLayFactorMass per1000 ft, lbRatedStrength,kipA,BNominalOutsideDiameter,in.Conductor Size Aluminum SteelCkcmil TypeD Code WordE Round TrapezoidalF Round1033.5 5 Snow

35、bird21 0.14817 0.174612 0.17317 0.871 16.012.411.51115 25.9 1.185954 13 Cardinal 8 0.214713 0.21227 0.1329 14.211.51227 33.5 1.147954 7 Rail 8 0.208013 0.21637 0.0971 15.211.51073 26.1 1.103954 5 Phoenix 7 0.219613 0.21787 0.0836 15.611.51027 23.7 1.088795 16 Drake 9 0.186513 0.19267 0.1360 13.911.5

36、1093 31.8 1.077795 13 Condor 8 0.195712 0.20187 0.1213 14.211.51023 28.2 1.055795 10 Puffin 7 0.206712 0.20337 0.1056 14.711.5956 25.1 1.034795 7 Tern 7 0.203411 0.21447 0.0886 15.211.5893 21.9 1.013795 5 Macaw 6 0.216711 0.21607 0.0764 15.611.5856 19.8 0.999636 16 Grosbeak 9 0.166613 0.17237 0.1216

37、 13.911.5874 25.4 0.975636 13 Rook 8 0.174912 0.18067 0.1085 14.311.5818 22.9 0.955636 10 Goldfinch 7 0.184812 0.18197 0.0945 14.711.5765 20.1 0.935636 7 Killdeer 7 0.181512 0.18387 0.0793 15.211.5715 17.7 0.917636 5 Pipit 6 0.193811 0.19327 0.0684 15.811.5684 16.1 0.903556.5 16 Dove 9 0.155713 0.16

38、137 0.1138 14.011.5765 22.6 0.919556.5 13 Parakeet 8 0.163713 0.16627 0.1015 14.311.5716 20.0 0.901556.5 10 Sapsucker 7 0.172812 0.17027 0.0884 14.711.5669 17.8 0.882556.5 7 Sunbird 7 0.170711 0.17907 0.0741 15.211.5625 15.5 0.863556.5 5 Blackbird 6 0.182010 0.18921 0.1692 15.811.5599 13.6 0.843477

39、16 Hawk 9 0.143813 0.14967 0.1053 14.011.5655.8 19.5 0.860477 13 Flicker 8 0.151513 0.15027 0.0940 14.411.5613.5 17.2 0.843477 10 Toucan 7 0.159912 0.15767 0.0818 14.811.5573.4 15.3 0.824477 7 Jackdaw 7 0.157712 0.15897 0.0686 15.211.5535.8 13.3 0.808477 5 Kestrel 6 0.165610 0.17681 0.1566 16.011.55

40、13.3 11.7 0.787397.5 16 Ibis 9 0.127814 0.13387 0.0961 14.211.5546.5 16.4 0.771397.5 10 Stork 7 0.142412 0.14597 0.0747 15.011.5477.9 12.9 0.750397.5 7 Longspur 6 0.150111 0.15441 0.1657 15.811.5446.1 10.6 0.725397.5 5 Erne 6 0.1558 1 0.1430 15.6 427.7 9.74 0.71710 0.1587 11.5336.4 16 Linnet 10 0.10

41、41 7 0.0884 14.7 462.4 14.3 0.71616 0.1194 11.5336.4 10 Woodcock 8 0.1215 7 0.0687 15.1 404.5 11.0 0.68814 0.1249 11.5336.4 7 Hummingbird 6 0.1406 1 0.1525 15.6 377.7 9.13 0.66411 0.1407 11.5336.4 5 Cowbird 6 0.1416 1 0.1315 15.9 361.9 8.5 0.66710 0.1470 11.5266.8 16 Partridge 10 0.0881 7 0.0788 15.

42、0 367.0 11.35 0.64512 0.1256 11.5266.8 10 Spoonbill 8 0.0978 1 0.1619 16.0 320.0 8.45 0.61011 0.1315 11.3266.8 7 Eider 7 0.1080 1 0.1358 16.0 299.4 7.61 0.60113 0.1193 11.2B701/B701M 1344. Ordering Information4.1 Orders for material under this specification shall include the following information:4.

43、1.1 Quantity of each size and type (Note 1),4.1.2 Conductor size: kcmil area,4.1.3 Conductor type and number of wires, aluminum and steel (Table 1),4.1.4 Type of steel core wire and if zinc or Zn-5 %Al-MM alloy coated, area density (ClassesA, B, and C) of coating (see 5.2),4.1.5 Special tension test

44、, if required (see 9.2),4.1.6 Place of inspection (Section 15),4.1.7 Package size (see 16.1),4.1.8 Special package marking, if required (Section 17), and4.1.9 Heavy wood lagging, if required (see 16.3).5. Requirement For Wires5.1 Before stranding, the round and trapezoidal aluminum wires shall confo

45、rm to the requirements of SpecificationB230/B230M except for shape and diameter tolerance of the trapezoidal wires. The tensile strength and elongation requirementsof trapezoidal wires shall be the same as for round wires of equal area. The area tolerances shall be such that the finished conductorco

46、nforms to Section 12.5.2 Before stranding, the steel core wire shall meet the requirements of Specifications B341/B341M, B498/B498M, B502,B606, B802/B802M, or B803, whichever is applicable.6. Joints6.1 Electric-butt welds, electric-butt, cold-upset welds, or cold-pressure welds may be made in the in

47、dividual aluminum wiresduring the stranding process. No weld shall occur within 50 ft. 15 m of any other weld in the completed conductor(Explanatory Note 3).6.2 There shall be no joints made in the finished steel wires.TABLE 1 ContinuedStranding Number of Wires and Diameter, in.A NominalAlumi-numLay

48、FactorMass per1000 ft, lbRatedStrength,kipA,BNominalOutsideDiameter,in.Conductor Size Aluminum SteelCkcmil TypeD Code WordE Round TrapezoidalF Round266.8 5 Titmouse 6 0.1183 1 0.1171 16.0 286.9 6.92 0.59312 0.1234 11.1A Conversion Factors:1 kcmil = 0.5067 mm21 in. = 25.4 mm1 kip = 1000 lbf = 4.448 kN.B Rated strengths of complete conductors are calculated in accordance with 9.1 and with ClassAzinc-coated steel core wire in accordance with Specifica