ASTM B701 B701M-2006 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规范》.pdf

《ASTM B701 B701M-2006 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B701 B701M-2006 Standard Specification for Concentric-Lay-Stranded Self-Damping Aluminum Conductors Steel Reinforced (ACSR SD)《同芯绞捻自阻钢芯加强铝导线(ACSR SD)的标准规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 701/B 701M 06Standard Specification forConcentric-Lay-Stranded Self-Damping AluminumConductors, Steel Reinforced (ACSR/SD)1This standard is issued under the fixed designation B 701/B 701M; the number immediately following the designation indicates the yearof original adoption or, in t

2、he case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor, s

3、teel-reinforced (ACSR/SD),and its component wires for use as overhead electrical conduc-tors (Explanatory Notes 1 and 2).1.2 The values stated in inch-pound or SI units are to beregarded separately as standard. Each system shall be usedindependently of the other. Combining values from the twosystems

4、 may result in non-conformance with the specification.For conductor sizes designated by AWG or kcmil, the require-ments in SI units have been numerically converted fromcorresponding values stated or derived in inch-pound units. Forconductor sizes designated by SI units only, the requirementsare stat

5、ed or derived in SI units.1.2.1 For density, resistivity, and temperature, the valuesstated in SI units are to be regarded as standard.NOTE 1ACSR/SD is designed to control aeolian vibration by integraldamping. The conductors consist of a central core of a round steel wire orwires surrounded by two l

6、ayers of trapezoidal aluminum 1350-H19 wiresor two layers of trapezoidal aluminum 1350-H19 wires and one layer ofround aluminum 1350-H19 wires (Fig. 1). The trapezoidal-wire layers areseparated from each other and from the steel core by two small annulargaps that provide the conductors self-damping

7、characteristics. The roundaluminum wires are in tight layer contact between themselves and theunderlying trapezoidal wire layer. Different strandings of the same size ofconductor are identified by type, which is the approximate ratio of steelarea to aluminum area, expressed in percent (Table 1 and T

8、able 2).NOTE 2The aluminum and temper designations conform to ANSIStandard H 35.1. Aluminum 1350 corresponds to UNS A91350 inaccordance with Practice E 527.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of

9、 this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced

10、 herein.2.2 ASTM Standards:2B 230/B 230M Specification for Aluminum 1350-H19 Wirefor Electrical PurposesB 232/B 232M Specification for Concentric-Lay-StrandedAluminum Conductors, Coated Steel-Reinforced (ACSR)B 263 Test Method for Determination of Cross-SectionalArea of Stranded ConductorsB 341/B 34

11、1M Specification for Aluminum-Coated (Alu-minized) Steel Core Wire for Aluminum Conductors, SteelReinforced (ACSR/AZ)B 354 Terminology Relating to Uninsulated Metallic Elec-trical ConductorsB 498/B 498M Specification for Zinc-Coated (Galvanized)Steel Core Wire for Aluminum Conductors, Steel Rein-for

12、ced (ACSR)B 502 Specification forAluminum-Clad Steel Core Wire forAluminum Conductors, Aluminum-Clad Steel ReinforcedB 549 Specification for Concentric-Lay-Stranded Alumi-num Conductors, Aluminum-Clad Steel Reinforced(ACSR/AW)B 606 Specification for High-Strength Zinc-Coated (Galva-nized) Steel Core

13、 Wire forAluminum andAluminumAlloyConductors, Steel ReinforcedB 802/B 802M Specification for Zinc-5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for AluminumConductors, Steel Reinforced (ACSR)B 803 Specification for High-Strength Zinc-5 %Aluminum-Mischmetal Alloy-Coated Steel Core Wire forAlum

14、inum and Aluminum-Alloy Conductors, Steel Rein-forced1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.07 onConductors of Light Metals.Current edition approved March 1, 2006. Published March 2006. Original

15、lyapproved in 1981. Last previous edition approved in 2000 as B 701/B 701M 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page on

16、the ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE 527 Practice for Numbering Metals and Alloys (UNS)2.3 ANSI Documents

17、:3ANSI H35.1 American National Standard Alloy and Tem-per Designation Systems for Aluminum2.4 NIST Documents:4NBS Handbook 100 Copper Wire Tables of the NationalBureau of Standards2.5 Aluminum Association Documents:5Publication 50, Code Words for Overhead Aluminum Elec-trical Conductors3. Terminolog

18、y3.1 Definitions of Terms Specific to This Standard:3.1.1 ACSR/SD covered by this specification has five typesof coated core wire and one type of aluminum-clad core wirewhich are designated by abbreviations as follows (ExplanatoryNote 2):3.1.1.1 ACSR/SD/AWACSR/SD using aluminum-cladsteel wire (Speci

19、fication B 502).3.1.1.2 ACSR/SD/AZACSR/SD using aluminum-coated(aluminized) steel wire (Specification B 341/B 341M).3.1.1.3 ACSR/SD/GAACSR/SD using Class A zinc-coated steel wire (Specification B 498/B 498M).3.1.1.4 ACSR/SD/GBACSR/SD using Class B zinc-coated steel wire (Specification B 498/B 498M).

20、3.1.1.5 ACSR/SD/GCACSR/SD using Class C zinc-coated steel wire (Specification B 498/B 498M).3.1.1.6 ACSR/SD/HSACSR/SD using extra highstrengthsteel wire (Specification B 606).3.1.1.7 ACSR/SD/MAACSR/SD using Class A zinc-5 %aluminum-mischmetal alloy-coated steel core wire (Specifica-tion B 802/B 802M

21、).3.1.1.8 ACSR/SD/MBACSR/SD using Class B zinc-5 %aluminum-mischmetal alloy-coated steel core wire (Specifica-tion B 802/B 802M).3.1.1.9 ACSR/SD/MCACSR/SD using Class V zinc-5 %aluminum-mischmetal alloy-coated steel core wire (Specifica-tion B 802/B 802M).3.1.1.10 ACSR/SD/MSACSR/SD using high-streng

22、thzinc-5 % Aluminum-mischmetal alloy-coated steel core wire(Specification B 803).3.2 For definitions of terms relating to conductors, refer toTerminology Standard B 354.4. Ordering Information4.1 Orders for material under this specification shall includethe following information:4.1.1 Quantity of ea

23、ch size and type (Note 1),4.1.2 Conductor size: kcmil area,4.1.3 Conductor type and number of wires, aluminum andsteel (Table 1),4.1.4 Type of steel core wire and if zinc or Zn-5 % Al-MMalloy coated, area density (Classes A, B, and C) of coating (see5.2),4.1.5 Special tension test, if required (see

24、9.2),4.1.6 Place of inspection (Section 15),4.1.7 Package size (see 16.1),4.1.8 Special package marking, if required (Section 17), and4.1.9 Heavy wood lagging, if required (see 16.3).5. Requirement For Wires5.1 Before stranding, the round and trapezoidal aluminumwires shall conform to the requiremen

25、ts of Specification B 230except for shape and diameter tolerance of the trapezoidalwires. The tensile strength and elongation requirements oftrapezoidal wires shall be the same as for round wires of equalarea. The area tolerances shall be such that the finishedconductor conforms to Section 12.5.2 Be

26、fore stranding, the steel core wire shall meet therequirements of Specifications B 341/B 341M, B 498/B 498M,B 502, B 606, B 802/B 802M, or B 803, whichever is appli-cable.6. Joints6.1 Electric-butt welds, electric-butt, cold-upset welds, orcold-pressure welds may be made in the individual aluminumwi

27、res during the stranding process. No weld shall occur within50 ft. 15 m of any other weld in the completed conductor(Explanatory Note 3).6.2 There shall be no joints made in the finished steel wires.7. Lay7.1 The nominal lay factors for the trapezoidal aluminumwires are shown in Table 1 (Explanatory

28、 Note 1 and Note 4).7.2 The lay factor for the round aluminum wires shall be notless than 10 nor more than 13.7.3 The lay factor for the 6-wire layer of 7 and 19-wire steelcores shall be not less than 18 nor more than 30.7.4 The lay factor for the 12-wire layer of 19-wire steelcores shall be no less

29、 than 16 nor more than 24.7.5 The direction of lay of the outside layer of aluminumwires shall be right-hand.7.6 The direction of lay of the aluminum and steel wiresshall be reversed in successive layers.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York

30、, NY 10036.4Available from National Institute of Standards and Technology (NIST), 100Bureau Dr., Stop 3460, Gaithersburg, MD 20899-34605Available from Aluminum Association Inc., 900 19th Street, NW, Suite 300,Washington, DC 20006.FIG. 1 Illustrations of Typical ACSR/SD StrandingsB 701/B 701M 0627.7

31、For the purpose of this specification the lay factor is thelength of lay of a given layer divided by its outside diameter.8. Construction8.1 The nominal aluminum cross-sectional area, type,stranding, and equivalent wire diameters shall be as shown inTable 1 (Explanatory Note 1).8.2 The smaller sizes

32、 ofACSR/SD consist of a steel core, aninner gap surrounded by a layer of trapezoidal aluminum wires(called the inner layer), and an outer gap surrounded by asecond layer of trapezoidal aluminum wire (called the outerlayer). The larger sizes of ACSR/SD consist of a steel core, aninner gap surrounded

33、by a layer of trapezoidal aluminum wires(called the inner layer), an outer gap surrounded by a layer oftrapezoidal aluminum wires (called the middle layer), and alayer of round aluminum wires (called the outer layer) fittingtightly over the middle layer. The diameter and number of steelcore wires, t

34、he number and equivalent round wire diameters ofthe trapezoidal aluminum wires, and the number and diameterof the round aluminum wires shall be as shown in Table 1.8.3 All conductor gaps shall be measured radially. Thenominal thickness of the gap is 0.030 in. 0.75 mm. Thetolerance of both the inner

35、and outer gaps shall be plus 0.000in. 0.00 mm and minus 0.010 in. 0.25 mm.TABLE 1 Construction Requirements of Aluminum Conductors, Self Damping, Concentric-Lay-Stranded, Steel-ReinforcedStranding Number of Wires and Diameter, in.ANominalAlumi-numLayFactorMass per1000 ft, lbRatedStrength,kipA,BNomin

36、alOutsideDiameter,in.Conductor Size Aluminum SteelCkcmil TypeDCode WordERound TrapezoidalFRound2156 8 Bluebird21 3 0.214510 3 0.217915 3 0.218419 3 0.0961 14.512.111.02504 60.7 1.7161780 8 Chukar21 3 0.19579 3 0.204113 3 0.215019 3 0.0874 14.512.011.02068 51.1 1.5651780 5 Smew21 3 0.19148 3 0.217114

37、 3 0.21287 3 0.1144 16.012.511.51921 43.6 1.5311590 13 Falcon24 3 0.169010 3 0.189114 3 0.197719 3 0.1030 13.511.711.52039 55.1 1.5211590 7 Lapwing21 3 0.18358 3 0.205912 3 0.21307 3 0.1253 15.912.811.51791 42.6 1.4681590 5 Ratite23 3 0.16698 3 0.209513 3 0.21437 3 0.1083 15.412.511.51715 39.1 1.447

38、1431 13 Plover24 3 0.160910 3 0.179214 3 0.186819 3 0.0977 13.511.711.51835 49.6 1.4481431 7 Bobolink21 3 0.17478 3 0.194612 3 0.20157 3 0.1189 15.112.211.51612 38.9 1.3981431 5 Popinjay21 3 0.17268 3 0.193613 3 0.19727 3 0.1025 16.012.511.51544 35.3 1.3811351.5 13 Martin21 3 0.177211 3 0.160415 3 0

39、.165219 3 0.0949 14.712.811.51733 46.8 1.4171351.5 10 Frigate21 3 0.17359 3 0.178614 3 0.17577 3 0.1377 14.512.211.01629 41.7 1.3891351.5 7 Dipper21 3 0.17018 3 0.189012 3 0.19547 3 0.1155 15.212.211.01522 36.7 1.3611351.5 5 Ringdove21 3 0.16808 3 0.194612 3 0.19497 3 0.0997 16.012.811.51458 33.4 1.

40、3441272 13 Pheasant21 3 0.172311 3 0.155215 3 0.159919 3 0.0921 14.712.811.51631 44.1 1.3781272 7 Bittern21 3 0.16538 3 0.182912 3 0.18947 3 0.1121 14.512.311.51433 34.6 1.3231272 5 Scissortail21 3 0.16317 3 0.192911 3 0.20297 3 0.0967 15.712.311.51372 31.4 1.3051192.5 13 Grackle 10 3 0.2147 19 3 0.

41、0892 14.2 1526 41.9 1.27416 3 0.2138 11.51192.5 7 Bunting 8 3 0.1768 7 3 0.1085 15.1 1343 32.4 1.28412 3 0.1831 12.221 3 0.1604 11.5B 701/B 701M 063TABLE 1 ContinuedStranding Number of Wires and Diameter, in.ANominalAlumi-numLayFactorMass per1000 ft, lbRatedStrength,kipA,BNominalOutsideDiameter,in.C

42、onductor Size Aluminum SteelCkcmil TypeDCode WordERound TrapezoidalFRound1192.5 5 Oxbird21 3 0.15827 3 0.186811 3 0.19607 3 0.0936 15.712.311.51286 29.5 1.2661113 13 Finch 9 3 0.2188 19 3 0.0862 14.2 1424 39.1 1.23315 3 0.2133 11.51113 7 Bluejay 8 3 0.1705 7 3 0.1049 15.9 1254 30.3 1.24212 3 0.1765

43、12.821 3 0.1553 11.51113 5 Avocet21 3 0.15337 3 0.181812 3 0.17987 3 0.0904 16.012.411.51200 27.5 1.2261033.5 13 Curlew 9 3 0.210614 3 0.21297 3 0.1383 14.211.51329 36.3 1.1911033.5 7 Ortolan 8 3 0.216814 3 0.21677 3 0.1010 15.211.51161 28.1 1.1451033.5 5 Snowbird21 3 0.14817 3 0.174612 3 0.17317 3

44、0.871 16.012.411.51115 25.9 1.185954 13 Cardinal 8 3 0.214713 3 0.21227 3 0.1329 14.211.51227 33.5 1.147954 7 Rail 8 3 0.208013 3 0.21637 3 0.0971 15.211.51073 26.1 1.103954 5 Phoenix 7 3 0.219613 3 0.21787 3 0.0836 15.611.51027 23.7 1.088795 16 Drake 9 3 0.186513 3 0.19267 3 0.1360 13.911.51093 31.

45、8 1.077795 13 Condor 8 3 0.195712 3 0.20187 3 0.1213 14.211.51023 28.2 1.055795 10 Puffin 7 3 0.206712 3 0.20337 3 0.1056 14.711.5956 25.1 1.034795 7 Tern 7 3 0.203411 3 0.21447 3 0.0886 15.211.5893 21.9 1.013795 5 Macaw 6 3 0.216711 3 0.21607 3 0.0764 15.611.5856 19.8 0.999636 16 Grosbeak 9 3 0.166

46、613 3 0.17237 3 0.1216 13.911.5874 25.4 0.975636 13 Rook 8 3 0.174912 3 0.18067 3 0.1085 14.311.5818 22.9 0.955636 10 Goldfinch 7 3 0.184812 3 0.18197 3 0.0945 14.711.5765 20.1 0.935636 7 Killdeer 7 3 0.181512 3 0.18387 3 0.0793 15.211.5715 17.7 0.917636 5 Pipit 6 3 0.193811 3 0.19327 3 0.0684 15.81

47、1.5684 16.1 0.903556.5 16 Dove 9 3 0.155713 3 0.16137 3 0.1138 14.011.5765 22.6 0.919556.5 13 Parakeet 8 3 0.163713 3 0.16627 3 0.1015 14.311.5716 20.0 0.901556.5 10 Sapsucker 7 3 0.172812 3 0.17027 3 0.0884 14.711.5669 17.8 0.882556.5 7 Sunbird 7 3 0.170711 3 0.17907 3 0.0741 15.211.5625 15.5 0.863

48、556.5 5 Blackbird 6 3 0.182010 3 0.18921 3 0.1692 15.811.5599 13.6 0.843477 16 Hawk 9 3 0.143813 3 0.14967 3 0.1053 14.011.5655.8 19.5 0.860477 13 Flicker 8 3 0.151513 3 0.15027 3 0.0940 14.411.5613.5 17.2 0.843477 10 Toucan 7 3 0.159912 3 0.15767 3 0.0818 14.811.5573.4 15.3 0.824477 7 Jackdaw 7 3 0

49、.157712 3 0.15897 3 0.0686 15.211.5535.8 13.3 0.808477 5 Kestrel 6 3 0.165610 3 0.17681 3 0.1566 16.011.5513.3 11.7 0.787397.5 16 Ibis 9 3 0.127814 3 0.13387 3 0.0961 14.211.5546.5 16.4 0.771397.5 10 Stork 7 3 0.142412 3 0.14597 3 0.0747 15.011.5477.9 12.9 0.750397.5 7 Longspur 6 3 0.150111 3 0.15441 3 0.1657 15.811.5446.1 10.6 0.725B 701/B 701M 064TABLE 1 ContinuedStranding Number of Wires and Diameter, in.ANominalAlumi-numLayFactorMass per1000 ft, lbRatedStrength,kipA,BNominalOutsideDiameter,in.Conductor Size Aluminum SteelCkcmil TypeDCode WordERound Trapezo