ASTM B617-1998(2016) Standard Specification for Coin Silver Electrical Contact Alloy《硬币银电接触合金的标准规格》.pdf

《ASTM B617-1998(2016) Standard Specification for Coin Silver Electrical Contact Alloy《硬币银电接触合金的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B617-1998(2016) Standard Specification for Coin Silver Electrical Contact Alloy《硬币银电接触合金的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B617 98 (Reapproved 2016)Standard Specification forCoin Silver Electrical Contact Alloy1This standard is issued under the fixed designation B617; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio

2、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers 90 % silver-10 % c

3、opper alloytubing, rod, wire, strip, and sheet material for electricalcontacts.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 Th

4、is standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateSafety Data Sheet (SDS) for this product/material as providedby the

5、 manufacturer, to establish appropriate safety and healthpractices, and determine the applicability of regulatory limi-tations prior to use.2. Referenced Documents2.1 ASTM Standards:2B277 Test Method for Hardness of Electrical Contact Mate-rialsB476 Specification for General Requirements for Wrought

6、Precious Metal Electrical Contact Materials3. Manufacture3.1 Raw materials shall be of such quality and purity thatthe finished product will have the properties and characteristicsprescribed in this specification.3.2 The material shall be finished by such operations (coldworking, heat treating, anne

7、aling, turning, grinding, or pick-ling) as are required to produce the prescribed properties.4. Chemical Composition4.1 Material produced under this specification shall meet therequirements for chemical composition prescribed in Table 1.5. Mechanical Requirements5.1 Mechanical properties shall confo

8、rm to the listings ofTable 2 or Table 3.5.2 All test specimens shall be full thickness or diameterwhen practical.5.3 All tests are to be conducted at room temperature, about68F (20C).6. General Requirements6.1 The provisions of Specification B476 shall apply to allmaterials produced to this specific

9、ation.7. Inspection and Testing7.1 Material furnished under this specification shall beinspected by the manufacturer as detailed in the applicableprovisions of Specification B476 and as listed as follows:7.1.1 Visual inspection at 10.7.1.2 Temper test (hardness or tension, but not both). Atension te

10、st is recommended for strip below 0.030-in. (0.8-mm)thickness and for wire of any diameter.7.1.3 Dimensional tests.7.1.4 Spectrographic or chemical analysis when indicatedby the purchaser order.8. Keywords8.1 arcing contacts; coin silver alloy; compositions; electri-cal contacts; impurities; preciou

11、s metals; silver alloy; silvercopper alloy1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.05 on Precious Metals and Electrical Contact Materials.Current edition approved May 1, 2016. Published May

12、2016. Originallyapproved in 1977. Last previous edition approved in 2010 as B617 98 (2010).DOI: 10.1520/B0617-98R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to

13、the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 2 Mechanical Properties of Sheet and StripTemperReduction inB or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ from DLA Document Services, Building 4/D, 700 Robbins Ave.,Philadelphia, PA 19111-5094, http:/quicksearch.dla.mil.B617 98 (2016)3