ASTM B103 B103M-2015 Standard Specification for Phosphor Bronze Plate Sheet Strip and Rolled Bar《磷青铜厚板 薄板 带材和轧制棒材的标准规格》.pdf

《ASTM B103 B103M-2015 Standard Specification for Phosphor Bronze Plate Sheet Strip and Rolled Bar《磷青铜厚板 薄板 带材和轧制棒材的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B103 B103M-2015 Standard Specification for Phosphor Bronze Plate Sheet Strip and Rolled Bar《磷青铜厚板 薄板 带材和轧制棒材的标准规格》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B103/B103M 10B103/B103M 15Standard Specification forPhosphor Bronze Plate, Sheet, Strip, and Rolled Bar1This standard is issued under the fixed designation B103/B103M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification es

3、tablishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leadedphosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzescommonly are used for deep drawing into bellows and stamping and forming into sp

4、ring devices and into terminals and connectorsfor electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used wherestrength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing

5、thrust washers. The following alloys are covered:Copper AlloyUNS No.2Nominal Composition, % Previously UsedDesignationCopper Tin Zinc LeadC51000 95 5 . . . . . . A1C51100 96 4 . . . . . . AC51180 96 4 . . . . . . . . .C51900 94 6 . . . . . .C52100A 92 8 . . . . . . CC52180 92 8 . . . . . . . . .C524

6、00 90 10 . . . . . . DC53400 94 5 . . . 1 B1C54400 88 4 4 4 B2C54400 88 4 3 4 B2_A SAE Specification CA 521 conforms to the requirements of UNS No. C52100.NOTE 1All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.1.2 T

7、he values stated in either SIinch-pound units or inch-poundSI units are to be regarded separately as standard. Within thetext, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shallbe used independently of the other. Combining valu

8、es from the two systems may result in non-conformance with the standard.1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the re

9、sponsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:3B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet,

10、 Strip, and Rolled BarB248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar(Metric)B601 Classification for Temper Designations for Copper and Copper AlloysWrought and Cast1 This specification is under the jurisdiction of ASTM Committee B

11、05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved April 1, 2010May 15, 2015. Published May 2010June 2015. Originally approved in 1936. Last previous edition approved in 20092010 asB103/B103M 09.B103/B103M 10. DOI

12、: 10.1520/B0103_B0103M-10. 10.1520/B0103_B0103M-15.2 The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard designation system accomplished by the addition of aprefix “C” and a suffix “00.” The suffix can be used to accommodate composition variat

13、ions of the base alloy.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard

14、and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases onl

15、y the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1B846 Terminology for

16、Copper and Copper AlloysE8E8/E8M Test Methods for Tension Testing of Metallic MaterialsE8M Test Methods for Tension Testing of Metallic Materials Metric (Withdrawn 2008)4E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)4E62 Test Methods for Chemical Analysis of C

17、opper and Copper Alloys (Photometric Methods) (Withdrawn 2010)4E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys (Withdrawn 2010)4E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical CompositionE478 Test Methods for Chemical Analys

18、is of Copper AlloysE527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)3. General Requirements3.1 The following sections of Specifications B248 and B248M constitute a part of this specification.3.1.1 Terminology,3.1.2 Materials and Manufacturing,3.1.3 Workmanship, Fini

19、sh, and Appearance,3.1.4 Sampling, Except for Chemical Analysis,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods, Except for Chemical Analysis,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Test Report

20、s,3.1.13 Packaging and Package Marking, and3.1.14 Supplementary Requirements.3.2 In addition, when a section with a title identical to that referenced in 5.1 appears in this specification, it contains additionalrequirements, which supplement those appearing in Specifications B248 and B248M4. Termino

21、logy4.1 DefinitionsFor definitions of terms used in this specification, refer to Terminology B846.5. Ordering Information5.1 Contracts or purchase Include the following specified choices when placing orders for product under this specificationshould include the following information:specification, a

22、s applicable:5.1.1 ASTM designation and year of issue (for example, B103/B103M 04);5.1.2 Copper AlloyAlloy UNS No. designation (for example, C51000);5.1.3 Temper (Section Temper;8);5.1.4 Dimensions: thickness, width, length, and so forth (Section forth;12);5.1.5 Form: plate, sheet, strip, or rolled

23、bar;5.1.6 How furnished: coils, specific length or stock lengths, with or without ends;5.1.7 Quantity: total weight each form, temper, and size; and,5.1.8 When material is purchased for agencies of the U.S. Government (Section Government.11).5.2 The following options are available under this specifi

24、cation and should be specified in the contract or purchase order whenrequired.but may not be included unless specified at the time of placing of the order when required;5.2.1 Type of edge: slit, sheared, sawed, square corners, round corners, rounded edges, or full rounded edges;5.2.2 Width and strai

25、ghtness tolerances (Section tolerances;12);5.2.3 Heat identification or traceability details;5.2.4 Certification, and5.2.5 Mill test report.Test Report.5. General Requirements5.1 The following sections of Specification B248 constitute a part of this specification.5.1.1 Terminology,5.1.2 Materials an

26、d Manufacturing,4 The last approved version of this historical standard is referenced on www.astm.org.B103/B103M 1525.1.3 Workmanship, Finish, and Appearance,5.1.4 Sampling, Except for Chemical Analysis,5.1.5 Number of Tests and Retests,5.1.6 Specimen Preparation,5.1.7 Test Methods, Except for Chemi

27、cal Analysis,5.1.8 Significance of Numerical Limits,5.1.9 Inspection,5.1.10 Rejection and Rehearing,5.1.11 Certification,5.1.12 Test Reports (Mill),5.1.13 Packaging and Package Marking, and5.1.14 Supplementary Requirements.5.2 In addition, when a section with a title identical to that referenced in

28、5.1, appears in this specification, it contains additionalrequirements, which supplement those appearing in Specification B248.6. Materials and Manufacture6.1 Materials:6.1.1 The material of manufacture shall be a cast bar, cake, slab, orof Copper Alloy UNS No. C51000, C51100, C51180,C51900, C52100,

29、 C52180, C52400, C53400, or C54400 as specified in the ordering information.of such purity and soundness asto be suitable for processing into the products prescribed herein.6.1.2 In the event When specified in the contract or purchase order, that heat identification or traceability is required, thep

30、urchaser shall specify the details desired.NOTE 2Because ofDue to the discontinuous nature of the processing of castings into wrought products, it is not always practical to identify a specificcasting analysis with a specific quantity of finished material.6.2 Manufacture:6.2.1 The product shall be m

31、anufactured by such hot working, cold working, and annealing processes as to produce a uniformwrought structure in the finished product.6.2.2 The product shall be hot or cold worked to the finished size and subsequently annealed, when required, to meet the temperproperties specified.6.2.3 EdgesSlit

32、edges shall be furnished unless otherwise specified in the contract or purchase order.7. Chemical Composition7.1 The materials shall conform to the chemical compositionalcomposition requirements specified in Table 1 for the copperalloy UNS No. designation specified in the order.ordering information.

33、7.2 These composition limits do not preclude the presence of other elements. Limits for unnamed elements By agreementbetween the manufacturer and purchaser, limits may be established and analysis required by agreement between manufacturer orsupplier and purchaser.for unnamed elements.7.3 Copper, spe

34、cified as the “remainder,” may be taken as the difference between the sum of results of all the elementsanalyzeddetermined and 100 %. When all the elements in Table 1 are analyzed,determined, the sum of results for each alloy shallbe 99.5 % min.8. Temper8.1 M20 (as Hot-Rolled Material)The standard t

35、emper of sheet and plate produced by hot rolling and is as designated in Table2.TABLE 1 Chemical RequirementsComposition, %Element Copper Alloy UNS No.C51000 C51100 C51180 C51900 C52100 C52180 C52400 C53400A C54400ATin 4.2-5.8 3.5-4.9 3.5-4.9 5.0-7.0 7.0-9.0 7.0-9.0 9.0-11.0 3.5-5.8 3.5-4.5Phosphoru

36、s 0.03-0.35 0.03-0.35 0.01-0.35 0.03-0.35 0.03-0.35 0.01-0.35 0.03-0.35 0.03-0.35 0.01-0.50Iron, max 0.10 0.10 0.05-0.20 0.10 0.10 0.05-0.20 0.10 0.10 0.10Lead 0.05 max 0.05 max 0.05 max 0.05 max 0.05 max 0.05 max 0.05 max 0.8-1.2 3.0-4.0Zinc 0.30 max 0.30 max 0.30 max 0.30 max 0.20 max 0.30 max 0.2

37、0 max 0.30 max 1.5-4.5Nickel . . . . . . 0.05-0.20 . . . . . . 0.05-0.20 . . . . . . . . .Copper remainder remainder remainder remainder remainder remainder remainder remainder remainderA When specified for bearings, the phosphorus content shall be maintained from 0.01 to 0.15 %.B103/B103M 1538.1 H

38、(Rolled Material)The standard tempers of rolled material are as designated for products described in this specificationare given in Table 2 with prefix “H.” Former designations and the standard designations as defined in Classification .B601 areshown.NOTE 3The properties of special and nonstandard t

39、empers are subject to agreement between the manufacture and purchaser.8.1.1 M20 (as Hot-Rolled Material)The standard temper of sheet and plate produced by hot rolling as designated in Table 2.8.1.2 H (Rolled Material)The standard tempers of rolled material are as designated in Table 2 with prefix “H

40、.” Formerdesignations and the standard designations as defined in Classification B601 are shown.NOTE 3The properties of special and nonstandard tempers are subject to agreement between the manufacture and purchaser.8.1.3 O60 (Annealed)The standard temper is O60 (soft), as indicated in Table 2.8.3 O6

41、0 (Annealed)The standard temper is O60 (soft), as indicated in Table 2.9. Grain Size of Annealed Tempers9.1 Other than O60 (soft) temper, as indicated in Table 2, annealed tempers are special, and the material shall conform to grainsize requirements agreed upon between manufacturer and purchaser as

42、defined in Classification B601.10. Mechanical Property Requirements10.1 Tensile Strength Requirements : Requirements:10.1.1 Products ordered toProduct furnished under this specification in inch-pound units shall be tested in accordance with TestMethods E8 and shall conform to tensile strength requir

43、ements prescribed in ksi units in Table 2, when tested in accordance withTest Methods E8/E8M.10.1.2 Products ordered toProduct furnished under this specification in SI units shall be tested in accordance with Test MethodsE8M, and shall conform to tensile strength requirements prescribed in MPa units

44、 in Table 2, when tested in accordance with TestMethods E8/E8M.10.1.3 Acceptance or rejection based onupon mechanical properties shall depend only on the tensile strength.10.1.4 The tension test specimens shall be taken so the longitudinal axis of the specimens is parallel to direction of rolling.10

45、.2 Rockwell Hardness:10.2.1 The approximate Rockwell hardness values given in Table 2 are for general information and assistance in testing, andshall not be used as a basis for product rejection.NOTE 4The Rockwell hardness test offers a quick and convenient method of checking for general conformity

46、to the specification requirements fortemper, tensile strength, and grain size.11. Other Requirements11.1 Purchases for U.S. Government AgenciesWhen identified in the contract or purchase order, product purchased foragencies of the U.S. Government shall conform to the special government requirements

47、stipulated in the supplementalrequirements given in SpecificationSpecifications B248 and B248M.12. Dimensions, Mass, and Permissible Variations12.1 The dimensions and tolerances for product described by this specification shall be as specified in Specification B248 andB248M with particular reference

48、 to the following tables and related paragraphs in that specification.paragraphs.12.1.1 Thickness:12.1.1.1 TolerancesSee Table 1.12.1.2 Width:12.1.2.1 Tolerances for Slit Metal and Slit Metal with Rolled EdgesEdges. See Table 4.12.1.2.2 Tolerances for Square-Sheared MetalMetal. See Table 5.12.1.2.3

49、Tolerances for Sawed MetalMetal. See Table 6.12.1.3 Length:12.1.3.1 Tolerances for Straight LengthsLengths. See Table 7.12.1.3.2 Schedule of Minimum Lengths with EndsEnds. See Table 8.12.1.3.3 Tolerances for Squared-Sheared MetalMetal. See Table 9.12.1.3.4 Tolerances for Sawed MetalMetal. See Table 10.12.1.4 Straightness:12.1.4.1 Tolerances for Slit Metal or Slit Metal Either Straightened or Edge-RolledEdge-Rolled. See Table 11.12.1.4.2 Tolerances for Squared Sheared MetalMetal. See Table 12.12.1.4.3 Tolerance for Squared Sheared