ASTM A90 A90M-2007 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings《（大型）钢铁器件外层含锌或锌合金涂料重量标准试验方法》.pdf

《ASTM A90 A90M-2007 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings《（大型）钢铁器件外层含锌或锌合金涂料重量标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM A90 A90M-2007 Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings《（大型）钢铁器件外层含锌或锌合金涂料重量标准试验方法》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 90/A 90M 07Standard Test Method forWeight Mass of Coating on Iron and Steel Articles withZinc or Zinc-Alloy Coatings1This standard is issued under the fixed designation A 90/A 90M; the number immediately following the designation indicates the yearof original adoption or, in the case

2、of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This test

3、method covers procedures for determining theweight mass of coating on iron or steel sheet, wire, and otherarticles in which the coating is zinc or a zinc alloy, such aszinc-5 % aluminum (including zinc-5 % aluminum-mischmetal and zinc-5 % aluminum-0.1 % magnesium) or55 % aluminum-zinc. In the body o

4、f this test method, referenceto zinc coating shall be interpreted to also include zinc alloycoating except where specifically stated otherwise.1.2 The final results determined by this test method shall beexpressed in inch-pound units or SI units, depending on theunits used in the material specificat

5、ion to which the results areto be compared. Certain portions of the procedure involvingdetermination of specimen weight mass have traditionallybeen performed in SI units, and corresponding inch-poundunits are not included.1.3 For sheet products, the final results are expressed aseither coating weigh

6、t mass total both sides, or coating weightmass separately on each side, depending on the specifiedrequirements.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safe

7、ty and health practices and determine the applica-bility of regulatory limitations prior to use. For specific hazardsstatements see 5.1.2. Referenced Documents2.1 ASTM Standards:2A 653/A 653M Specification for Steel Sheet, Zinc-Coated(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)by the Hot-Di

8、p ProcessA 792/A 792M Specification for Steel Sheet, 55 %Aluminum-Zinc Alloy-Coated by the Hot-Dip ProcessA 875/A 875M Specification for Steel Sheet, Zinc-5 %Aluminum Alloy-Coated by the Hot-Dip ProcessD 1193 Specification for Reagent WaterE29 Practice for Using Significant Digits in Test Data toDet

9、ermine Conformance with Specifications3. Significance and Use3.1 This test method provides a standard method for deter-mining the weight mass of coating for comparison withspecification requirements. A coating of zinc on iron or steelarticles provides protection against corrosion.As the protectionis

10、 provided by sacrificial loss of zinc, the degree of protectionis proportional to the weight mass of zinc coating. Specifi-cations for zinc-coated articles frequently provide for differentclasses of coating so that the purchaser can select the coatingweight mass most suitable to his needs.4. Reagent

11、s4.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades ma

12、y beused, provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.4.2 Purity of WaterWater used to prepare chemical solu-tions shall be reagent water as defined by Type IV ofSpecification D 1193.4.3 Antimony

13、 Trichloride Solution Dissolve 20 g ofSb2O3or 32 g of SbCl3in 1000 mL of HCl (sp gr 1.18 to 1.19).4.4 Hydrochloric Acid (sp gr 1.18 to 1.19)Concentratedhydrochloric acid (HCl).4.5 Hydrochloric AcidAntimony Trichloride SolutionAdd 5 mL of antimony trichloride solution to 100 mL of HCl(sp gr 1.18 to 1

14、.19).1This test method is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.07 on Methods of Testing.Current edition approved May 1, 2007. Published June 2007. Originallyapproved in 1923. Last previous edition a

15、pproved in 2006 as A 90/A 90M - 06.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3“Reagent Chemicals, Ameri

16、can Chemical Society Specifications,” Am. Chemi-cal Soc., Washington, DC. For suggestions on the testing of reagents not listed bythe American Chemical Society, see “Analar Standards for Laboratory U.K.Chemicals,” BDH Ltd., Poole, Dorset, and the “United States Pharmacopeia.”1*A Summary of Changes s

17、ection appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.6 Hydrochloric Acid (1 + 1)Mix 500 mL of HCl (sp gr1.18 to 1.19) with 500 mL of reagent water and cool to roomtemperature.5. Hazards5.1 Warni

18、ngSmall amounts of the poisonous gas stibine(SbH3) may be evolved during the stripping process using thehydrochloric acid-antimony trichloride method. Hydrochloricacid fumes are present, and hydrogen gas is evolved in thestripping process. Therefore, the test should be performedunder conditions of a

19、dequate ventilation. A fume hood isrecommended for large numbers of samples or where the test isto be carried out frequently over extended periods of time.6. Sampling6.1 Zinc-Coated SheetsSamples for weight mass ofcoating determination shall be secured in accordance withSpecifications A 653/A 653M,

20、A 792/A 792M, or A 875/A 875M depending on the type of coating.NOTE 1For convenience in calculating test results in inch-poundunits, the specimen should have an area of 5.08 in.2of sheet (2.25 60.01-in. square or 2.54 6 0.01 in. in diameter). The weight mass ofcoating in grams on a specimen of that

21、area is numerically equal to theweight mass of coating in ounces per square foot of sheet. For results tobe reported in metric units, the specimen should have an area of 3330 mm2of sheet (57.7 6 0.1-mm square or 65.1 6 0.1 mm in diameter).6.2 Zinc-Coated WireSamples shall be secured as desig-nated i

22、n the appropriate specification. The specimen of wiremay be of any length over 12 in. 305 mm, but preferablyabout 24 in. 609 mm. Where a continuous length is notavailable, shorter lengths totaling over 12 in. 300 mm, butpreferably about 24 in. 600 mm, shall be used. Since thedensity of the steel is

23、known 0.283 lb/in.37830 kg/m3, it isnot necessary to use a specific length of specimen.6.3 Zinc-Coated Articles Other Than Sheet or WireSamples for weight mass of coating determination shall besecured as designated in the appropriate specification. Exceptas otherwise provided, the specimens should h

24、ave a minimumarea of 3 in.2(2000 mm2) of zinc-coated surface. For very smallitems, several pieces may have to be stripped to obtain theminimum area.6.3.1 In the case of threaded articles, such as bolts andscrews, the determination shall be made on a portion of thearticles that does not include any t

25、hread.7. Procedure7.1 Stripping of zinc alloy coatings containing less than90 % zinc shall be done using the dilute hydrochloric acidmethod. Stripping of coatings containing 90 % or more zincshall be done using either hydrochloric acid-antimony trichlo-ride solution or dilute hydrochloric acid (1 +

26、1) (alternativestandard method).7.2 Clean the specimens by washing with solvent naphtha orother suitable solvent, then rinse with alcohol, and dry thor-oughly.7.3 Determine the weight mass of the specimens individu-ally to the nearest 0.01 g, except for articles other than sheet orwire with a specim

27、en weight mass greater than 125 g,determine the weight mass to at least the nearest 0.1 g. Afterdetermining the weight mass, immerse each specimen singlyin the stripping solution and allow to remain until the violentevolution of hydrogen has ceased, and only a few bubbles arebeing evolved. This requ

28、ires about 15 to 30 s, except in thecase of sherardized coatings, which require a somewhat longertime. The same solution may be used repeatedly until the timerequired for stripping becomes inconveniently long. The tem-perature of the stripping solution shall at no time exceed 100F38C. After strippin

29、g, wash the specimens by scrubbing themunder running water, dip in hot water, and wipe or blow dry.Determine the weight mass of the specimens again, to thesame precision as in the initial determination.7.4 Sheet SpecimensWhen measuring the total coatingweight mass on both sides, or the single side c

30、oating weightmass on each side, determine the area of sheet (one surface)to the nearest 0.01 in.25 mm2. If specimens were prepared tothe dimensions as provided in Note 1, they shall be presumedto have an area of 5.08 in.23330 mm2. When it is not possibleto determine the area accurately, as in specim

31、ens from corru-gated sheets, the thickness of the stripped sheet shall bedetermined to the nearest 0.001 in. 0.01 mm.7.4.1 When determining the coating weight mass on oneside of sheet material, use the procedure described in 7.3,except use a “stop-off” to protect one side from the strippingmedium. A

32、cid-resistant paints or lacquers, acid-resistant tape,or mechanical devices fastened to the test specimen areexamples of commonly used “stop-off” materials. Apply the“stop-off” to the specimen after the initial determination ofweight mass and remove before the second determination ofweight mass. Bec

33、ause of the possibility of moisture absorp-tion during the stripping process, the “stop-off” must not be onthe specimen during either weight mass determinations.Determine the coating weight mass on the second sidesubsequently without a “stop-off” on the first side.7.5 Wire SpecimensDetermine the dia

34、meter of thestripped wire to the nearest 0.001 in. 0.01 mm by taking theaverage of two measurements at right angles to each other.7.6 Specimens Other Than Sheet or Wire Determine thetotal coated area of the original specimen to the nearest 0.01in.25 mm2. Alternatively, for specimens of uniform thick

35、nessof base metal, such as a piece of plate or pipe, determine theaverage thickness of the stripped specimen to the nearest 0.001in. 0.01 mm.8. Calculation8.1 Zinc-Coated Sheet:8.1.1 Results in Inch-Pound Units:8.1.1.1 When the area of one surface of the sheet isdetermined, calculate the weight mass

36、 of coating as follows:C 5 W12 W2!/A# 3 K (1)where:C = weight mass of coating, oz/ft2of sheet,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,A = area of one surface of the sheet, in.2or mm2, and,A 90/A 90M 072K = a constant = 5.08 when A is in in.2, or = 3.28 3 103wh

37、en A is in mm2.NOTE 2If the specimen was prepared to the dimensions as provided inNote 1, having an area of 5.08 in.2, the loss of weight mass in grams isnumerically equal to the weight mass of coating in ounces per squarefoot of sheet.8.1.1.2 When it is not possible to secure a specimen ofmeasurabl

38、e area, calculate the weight mass of coating asfollows:C 5 W12 W2!/W2# 3 T 3 K (2)where:C = weight mass of coating, oz/ft2of sheet,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,T = thickness of stripped sheet, in. or mm, andK = a constant = 652 when T is in in., or

39、= 25.7 when Tis in mm.8.1.2 Results in Metric Units:8.1.2.1 When the area of sheet is determined, calculate theweight mass of coating as follows:C 5 W12 W2!/A# 3K (3)where:C = weight mass of coating, g/m2of sheet,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,A = are

40、a of one surface of the sheet, in.2or mm2, andK = a constant = 1.55 3 103when A is in in.2,or=13106when A is in mm2.NOTE 3If the specimen was prepared to the dimensions as provided inNote 1, having an area of 3330 mm2of sheet, the factor K/A isapproximately 300, which may be used in the calculation.

41、8.1.2.2 When it is not possible to obtain a specimen ofmeasurable area, calculate the weight mass of coating asfollows:C 5 W12 W2!/W2# 3 T 3 K (4)where:C = weight mass of coating, g/m2of sheetW1= original weight mass of the specimen, g,W2= weight mass of the stripped specimen, g,T = thickness of str

42、ipped sheet, in. or mm, andK = a constant = 1.99 3 105when T is in in., or = 7.83 3103when T is in mm.8.2 Zinc-Coated Wire:8.2.1 Results in Inch-Pound Units:8.2.1.1 Calculate the weight mass of zinc coating asfollows:C 5 W12 W2!/W2# 3 D 3 M (5)where:C = weight mass of coating, oz/ft2of stripped wire

43、surface,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,D = diameter of stripped wire, in. or mm, andM = a constant = 163 when D is in in., or = 6.42 when Dis in mm.8.2.2 Results in Metric Units:8.2.2.1 Calculate the weight mass of zinc coating asfollows:C 5 W12 W2!/W

44、2# 3 D 3 M (6)where:C = weight mass of coating, g/m2of stripped wiresurface,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,D = diameter of stripped wire, in. or mm, andM = a constant = 4.97 3 104when D is in in., or = 1.963 103when D is in mm.8.3 Zinc-Coated Articles

45、 Other Than Sheet or Wire:8.3.1 Results in Inch-Pound Units:8.3.1.1 Calculate the weight mass of coating as follows:C 5 W12 W2!/A# 3 N (7)where:C = weight mass of coating, oz/ft2of surface,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,A = coated area of original spe

46、cimen, in.2or mm2, andN = a constant = 5.08 when A is in in.2, or = 3.28 3 103when A is in mm2.8.3.1.2 If the specimen has a uniform thickness of basemetal, calculate the weight mass of coating as follows:C 5 W12 W2!/ W2# 3 G 3 Z (8)where:C = weight mass of coating, oz/ft2of surface,W1= original wei

47、ght mass of specimen, g,W2= weight mass of stripped specimen, g,G = thickness of stripped specimen, in. or mm, andZ = a constant = 326 when G is in in., or 12.8 when G isin mm.8.3.2 Results in Metric Units:8.3.2.1 Calculate the weight mass of zinc coating asfollows:C 5 W12 W2!/A# 3N (9)where:C = wei

48、ght mass of coating, g/m2of surface,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,A = coated area of original specimen, in.2or mm2, andN = a constant = 1.55 3 103when A is in in.2,or=13106when A is in mm2.8.3.2.2 If the specimen has a uniform thickness of basemetal,

49、 calculate the weight mass of coating as follows:C5 W12 W2!/W2# 3G 3 Z (10)where:C = weight mass of coating, g/m2of surface,W1= original weight mass of specimen, g,W2= weight mass of stripped specimen, g,G = thickness of stripped specimen, in. or mm, andA 90/A 90M 073Z = a constant = 9.95 3 104when G is in in., or = 3.923 103when G is in mm.9. Report9.1 Weight mass of coating on zinc-coated