ASTM A467 A467M-2007 Standard Specification for Machine and Coil Chain《设备和盘链标准规范》.pdf

《ASTM A467 A467M-2007 Standard Specification for Machine and Coil Chain《设备和盘链标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A467 A467M-2007 Standard Specification for Machine and Coil Chain《设备和盘链标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 467/A 467M 07Standard Specification forMachine and Coil Chain1This standard is issued under the fixed designationA467/A467M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in pare

2、ntheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers welded carbon steel machinechain and coil chain.Although these chains are not intended forpocket wheel use, they can be u

3、sed for pocket and sprocketwheel use. This chain shall never be used for overhead liftingapplications.1.2 There are two classes each of machine and coil chain:1.2.1 Class MSMachine, straight-link steel chain,1.2.2 Class MTMachine, twist-link steel chain,1.2.3 Class CSCoil, straight-link chain, and1.

4、2.4 Class CTCoil, twist-link steel chain.1.3 The values stated in either inch-pound units or SI unitsshall be regarded separately as standard. Within the text, the SIunits are shown in brackets. The values stated in each systemmay not be exact equivalents; therefore, each system must beused independ

5、ently of the other, without combining values inany way.2. Referenced Documents2.1 ASTM Standards:2A 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel Products3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 breaking force, minimum, nminimum force inpoun

6、ds or newtons at which the chain, during manufacture, hasbeen found by representative testing to break when a constantlyincreasing force is applied in direct tension.3.1.1.1 DiscussionThis test is a manufacturers attributeacceptance test and shall not be used as criteria for service.3.1.2 lot, nfor

7、the purpose of acceptance testing, a lotshall consist of 3000 ft 1000 m, or fraction thereof, of thesame grade and size chain. If a continuous length of chainexceeds 3000 ft 1000 m, it shall also be considered a lot.3.1.3 overhead lifting, nprocess of lifting that wouldelevate a freely suspended loa

8、d such that dropping the loadwould present a possibility of bodily injury or propertydamage.3.1.4 proof test, nquality control tensile test applied tochain for the purpose of verifying weld and material quality.3.1.4.1 DiscussionIt is the minimum force in pounds ornewtons which the chain has withsto

9、od at the time it left theproducer, under a test in which a constantly increasing forcehas been applied in direct tension to a straight length of chain.Proof test loads are a manufacturing integrity test and shall notbe used as criteria for service or design purposes.3.1.5 working load limit (WLL),

10、nmaximum combinedstatic and dynamic load in pounds or kilograms that shall beapplied in direct tension to an undamaged, straight length ofchain.4. Ordering Information4.1 It shall be the responsibility of the purchaser to specifyall requirements that are necessary for material ordered underthis spec

11、ification. Such requirements to be considered include,but are not limited to, the following:4.1.1 ASTM SpecificationA 467/A 467M and year of issue,4.1.2 Trade size of chain,4.1.3 Class of chain,4.1.4 Quantity of chain in feet or metres,4.1.5 Length of each piece, if required,4.1.6 Finish, if require

12、d,4.1.7 Certification of test(s), if required, and4.1.8 Acceptance of inspection by purchaser, if required.5. Manufacture5.1 Melting ProcessThe steel shall be made by theopen-hearth, electric-furnace, or basic-oxygen process.1This specification is under the jurisdiction of ASTM Committee A01 on Stee

13、l,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.27 on Steel Chain.Current edition approved Nov. 1, 2007. Published November 2007. Originallyapproved in 1964. Last previous edition approved in 2006 as A 467/A 467M 01(2006).2For referenced ASTM standards, visit

14、 the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 1

15、00 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 Welding ProcessClasses MS, MT, CS, and CT shallbe electric welded.6. Chemical Requirements6.1 Product AnalysisThe material used shall conform tothe following chemical requirements:Elements, max, %Classes MS, MT,CS

16、, and CTCarbon 0.37Phosphorus 0.048Sulfur 0.0586.2 The analysis may be made by the purchaser from thebars or finished chain. Samples for analysis shall represent thefull cross section of the specimen.6.3 For referee purposes, Test Methods, Practices, andTerminology A 751 shall be used.7. Mechanical

17、Properties Requirements7.1 Proof TestAll chain in Classes MS and CS shall beproof tested to at least the proof load prescribed in Table 1 andTable 2 for the appropriate size and class chain. When sotested, it shall withstand these loads without loss of chainintegrity. Links or chain segments not wit

18、hstanding the prooftest load shall be removed from the chain.NOTE 1Chain Classes MT and CT do not require proof testing sincethe twist operation is an adequate verification of link integrity.7.2 Breaking Force Test:7.2.1 The tension test specimen shall consist of a lengthfrom the lot containing at l

19、east the number of links specified in7.3.1.7.2.2 Fixtures for securing chain in a testing machine shallbe properly designed to securely support the shoulder of thelink (Note 2). The opening in the fixture shall not be more than125 % of the stock diameter being tested. Links engaged in thetesting fix

20、ture shall not be considered part of the test specimen.NOTE 2U-bolts of the same or larger diameter and the same or greaterstrength than the chain may be used to secure the chain to the jaws of thetesting machine.7.2.3 Test specimens from the finished chain shall conformto the minimum breaking force

21、 requirements as prescribed inTables 1-4 for their respective sizes and classes.7.3 Elongation:7.3.1 The elongation test specimen shall consist of a lengthfrom the lot containing at least the number of links in Table 5.7.3.2 A positive load not exceeding 10 % of the proof testshall be applied for de

22、termining the original gauge length(L0).7.3.3 The elongation shall be based on the total extension atfracture. This is expressed as a percentage of the change inlength (DL) divided by the original gauge length (L0). Theelongation may be determined by the equation below or byautographic recorder or s

23、ide scale.Elongation %! 5 $DL/L$0% % 3 100where:DL = test specimen final length at fracture test speci-men original gauge length L0, andL0 = original gauge length (sum or the inside lengths ofthe test chain links, not counting the fixture links, oras determined in 7.3.2).7.3.4 The elongation shall b

24、e a minimum of 10 %.7.4 One test for breaking strength and elongation shall bemade from each lot. The elongation and breaking force testsmay be performed at the same time on the same test specimen.8. Dimensional Requirements8.1 The chain shall conform to the dimensional require-ments specified in Ta

25、bles 1-4 for the appropriate class and sizechain. Inside widths and lengths are not to exceed 65 % fromthe nominal dimensions.8.2 DiameterThe diameter of the material from which thechain is manufactured shall not be smaller than the materialdiameter listed in Table 1 and Table 2 within a tolerance o

26、f7 %. Oversized wire may be used for all applications.9. Finish9.1 The manufacturer may apply a surface treatment orfinish of his own choice for identification or corrosion resis-tance unless the customer specifies otherwise. The surfacetreatment or finish shall not alter the chain properties in ama

27、nner that would cause the chain to not meet the otherprovisions of this standard.TABLE 1 Machine ChainStraight Link(Not to be used in overhead lifting applications)Trade Size Material DiameterWorking Load Limit,maxProof Test,Amin Breaking Force,AminNominal InsideLengthBNominal InsideWidthBmm in. mm

28、lb kg lb kN lb kN in. mm in. mm3.0 4 0.120 3.0 215 98 430 1.91 860 3.82 0.55 14.0 0.21 5.33.4 3 0.135 3.4 270 122 540 2.40 1080 4.80 0.59 15.0 0.24 6.13.8 2 0.148 3.8 325 147 650 2.89 1300 5.78 0.61 15.5 0.26 6.64.1 1 0.162 4.1 390 177 780 3.47 1560 6.93 0.63 16.0 0.28 7.14.5 1/0 0.177 4.5 465 211 9

29、30 4.14 1860 8.27 0.74 18.8 0.31 7.94.9 2/0 0.192 4.9 545 247 1090 4.85 2180 9.69 0.78 19.8 0.34 8.65.3 3/0 0.207 5.3 635 288 1270 5.65 2540 11.29 0.85 21.6 0.36 9.15.5 4/0 0.218 5.5 700 318 1400 6.23 2800 12.44 0.99 25.1 0.38 9.66.4 5/0 0.250 6.4 925 420 1850 8.23 3700 16.44 1.07 27.2 0.44 11.2AThe

30、 Proof Test and Minimum Breaking Force shall not be used as criteria for service or design purposes. See Section 3.BActual inside lengths and widths should not vary more than 65 % from nominal dimensions.A 467/A 467M 07210. Retests10.1 If the original test specimen fails to conform to therequirement

31、s of 7.2.3, two additional test specimens from thesame lot may be tested. If both additional tests are satisfactory,the chain will be considered acceptable.11. Rework and Retreatment11.1 Chain that fails to comply to the requirements of thisspecification my be reworked and resubmitted.12. Inspection

32、12.1 When requested on the purchase order or contract, thechain shall be free of paint or other coatings which could masksurface discontinuities at the time of inspection.12.2 The manufacturer shall afford the purchasers inspectorall reasonable facilities necessary to verify that the material isbein

33、g furnished in accordance with this specification. Inspec-tion by the purchaser shall not unnecessarily interfere with themanufacturers operations. All tests and inspection shall bemade at the place of manufacture, unless otherwise agreedupon between the manufacturer and the purchaser.12.3 The purch

34、aser may make the tests to govern accep-tance or rejection of the material at their own laboratory orelsewhere. Tests and acceptance criteria shall conform to therequirements contained in this specification unless otherwiseTABLE 2 Coil ChainStraight Link(Not to be used in overhead lifting applicatio

35、ns)Trade Size Material DiameterWorking Load Limit,maxProof Test,Amin Breaking Force,AminNominal InsideLengthBNominal InsideWidthBmm in. mm lb kg lb kN lb kN in. mm in. mm3.0 4 0.120 3.0 205 93 410 1.82 820 3.64 1.11 28.1 0.21 5.323.4 3 0.135 3.4 255 116 510 2.27 1020 4.53 1.17 29.6 0.24 6.093.8 2 0.

36、148 3.8 310 141 620 2.76 1240 5.51 1.18 29.9 0.26 6.594.1 1 0.162 4.1 370 168 740 3.29 1480 6.58 1.25 31.7 0.28 7.104.5 1/0 0.177 4.5 440 200 880 3.91 1760 7.82 1.25 31.7 0.31 7.864.9 2/0 0.192 4.9 520 236 1040 4.63 2080 9.24 1.26 31.9 0.34 8.625.3 3/0 0.207 5.3 605 274 1210 5.38 2420 10.76 1.30 32.

37、9 0.36 9.135.5 4/0 0.218 5.5 670 304 1340 5.96 2680 11.91 1.39 35.2 0.38 9.646.4 5/0 0.250 6.4 880 399 1760 7.83 3520 15.64 1.52 38.5 0.44 11.20AThe Proof Test and Minimum Breaking Force shall not be used as criteria for service or design purposes. See Section 3.BActual inside lengths and widths sho

38、uld not vary more than 65 % from nominal dimensions.TABLE 3 Machine ChainTwist Link(Not to be used in overhead lifting applications)Trade Size Material Diameter Working Load Limit, max Breaking Force,Amin Nominal Inside LengthBNominal Inside WidthBmm in. mm lb kg lb kN in. mm in. mm3.0 4 0.120 3.0 2

39、05 93 820 3.64 0.52 13.1 0.17 4.33.4 3 0.135 3.4 255 116 1020 4.53 0.56 14.2 0.20 5.13.8 2 0.148 3.8 310 141 1240 5.51 0.58 14.7 0.21 5.34.1 1 0.162 4.1 370 168 1480 6.58 0.59 15.0 0.24 6.14.5 1/0 0.177 4.5 440 200 1760 7.82 0.68 17.2 0.26 6.64.9 2/0 0.192 4.9 520 236 2080 9.24 0.73 18.5 0.28 7.15.3

40、 3/0 0.207 5.3 605 274 2420 10.76 0.80 20.3 0.31 7.95.5 4/0 0.218 5.5 670 304 2680 11.91 0.89 22.5 0.32 8.16.4 5/0 0.250 6.4 880 400 3520 15.64 1.00 25.3 0.37 9.4AThe Minimum Breaking Force values shall not be used as criteria for service or design purposes. See Section 3.BActual inside lengths and

41、widths should not vary more than 65 % from nominal dimensions.TABLE 4 Coil ChainTwist Link(Not to be used in overhead lifting applications)Trade Size Material Diameter Working Load Limit, max Breaking Force,Amin Nominal Inside LengthBNominal Inside WidthBmm in. mm lb kg lb kN in. mm in. mm3.0 4 0.12

42、0 3.0 195 88 780 3.47 1.09 27.6 0.18 4.563.4 3 0.135 3.4 240 109 970 4.31 1.14 28.9 0.21 5.323.8 2 0.148 3.8 295 134 1180 5.25 1.15 29.1 0.22 5.584.1 1 0.162 4.1 350 159 1405 6.24 1.22 30.9 0.25 6.344.5 1/0 0.177 4.5 415 188 1670 7.43 1.22 30.9 0.27 6.854.9 2/0 0.192 4.9 495 225 1975 8.78 1.24 31.4

43、0.29 7.365.3 3/0 0.207 5.3 575 261 2300 10.23 1.26 31.9 0.32 8.125.5 4/0 0.218 5.5 635 288 2545 11.32 1.34 34.0 0.33 8.326.4 5/0 0.250 6.4 835 379 3345 14.86 1.47 37.3 0.38 9.65AThe Minimum Breaking Force values shall not be used as criteria for service or design purposes. See Section 3.BActual insi

44、de lengths and widths should not vary more than 65 % from nominal dimensions.TABLE 5 Mechanical Test Sample Length RequirementsSize of Chain Minimum Number of Links in Test Specimen2/0 and smaller 93/0 and larger 7A 467/A 467M 073stated in the purchase order or contract. Tests at the purchaserslabor

45、atory or elsewhere shall be made at the expense of thepurchaser.13. Rejection and Rehearing13.1 Materials that fail to conform to the requirements ofthis specification may be rejected. Rejection shall be promptlyreported, in writing, to the producer or supplier. In case ofdissatisfaction with the re

46、sults of the test, the producer orsupplier may make claim for a rehearing.13.2 In the case of dissatisfaction with the results of any testin 12.3, the manufacturer may make claim for a rehearing.14. Certification14.1 A manufacturers certification that the chain conformsto ASTM Specification A 467/A

47、467M of the year of issuespecified shall be furnished when requested on the purchaseorder or contract.14.2 When requested on the purchase order or contract, themanufacturer shall furnish a certificate of proof test to theproducer or his representative.15. Product Marking15.1 The chain may be marked

48、at the discretion of themanufacturer.15.2 Chain shall not be marked with indented characters.16. Keywords16.1 steel chainSUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue(A 467/A 467M 01 (2006) that may impact the use of this standa

49、rd. (Approved Nov. 1, 2007.)(1) Revised Section 2.(2) Added new referenced standard citation to 6.3.(3) Changed tolerance value in 8.2.(4) Revised Section 9.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time b