ASTM A1010 A1010M-2001(2009) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate Sheet and Strip《高强度马氏体不锈钢板、薄板和带材标准规范》.pdf
《ASTM A1010 A1010M-2001(2009) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate Sheet and Strip《高强度马氏体不锈钢板、薄板和带材标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM A1010 A1010M-2001(2009) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate Sheet and Strip《高强度马氏体不锈钢板、薄板和带材标准规范》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A 1010/A 1010M 01 (Reapproved 2009)Standard Specification forHigher-Strength Martensitic Stainless Steel Plate, Sheet, andStrip1This standard is issued under the fixed designation A 1010/A 1010M; the number immediately following the designation indicates theyear of original adoption or,
2、 in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers martensitic stainless steels forvarious structural, ar
3、chitectural, pressure vessel, and heat-resisting applications. The mechanical properties of thesesteels are customarily, but not necessarily, developed by asuitable heat treatment generally referred to as tempering.1.2 Steel products under this specification are available intwo grades:Grade Yield St
4、rength, min, ksi MPa40 275 40 27550 350 50 3501.3 The maximum thickness of plates is limited only by thecapacity of the composition to meet the specified mechanicalproperty requirements; however, current practice normallylimits the maximum thickness of plates furnished under thisspecification to 1 i
5、n. 25 mm.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conform
6、ancewith the standard.2. Referenced Documents2.1 ASTM Standards:2A 480/A 480M Specification for General Requirements forFlat-Rolled Stainless and Heat-Resisting Steel Plate,Sheet, and StripA 673/A 673M Specification for Sampling Procedure forImpact Testing of Structural SteelE 527 Practice for Numbe
7、ring Metals and Alloys in theUnified Numbering System (UNS)2.2 Other Document:SAE J1086 Recommended Practice for Numbering Metalsand Alloys33. General Requirements3.1 The following requirements for orders for materialfurnished under this specification shall conform to the appli-cable requirements of
8、 the current edition of Specification A480/A 480M.3.1.1 Terminology,3.1.2 Ordering Information,3.1.3 Process,3.1.4 Heat Analysis,3.1.5 Product Analysis,3.1.6 Finish for Sheet,3.1.7 Finish for Strip,3.1.8 Finish for Plates,3.1.9 Test Specimens,3.1.10 Number of Tests,3.1.11 Test Methods,3.1.12 Retests
9、 and Retreatment,3.1.13 Dimensions and Permissible Variations,3.1.14 Workmanship,3.1.15 Packaging, Marking, and Loading,3.1.16 Inspection,3.1.17 Rejection and Rehearing, and3.1.18 Material Test Report and Certification.4. Chemical Composition4.1 The steel shall conform to the requirements as tochemi
10、cal composition specified in Table 1, and shall conformto applicable requirements specified in the current edition ofSpecification A 480/A 480M.5. Heat Treatment5.1 The material shall be heat-treated by tempering to meetthe requirements of this specification. The tempering tempera-ture shall not exc
11、eed 1400F 760C. Prior to tempering, thesteel shall be in the as-rolled, normalized or quenched condi-tion.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA1010A1010M20012009STANDARDSPECIFICATIONFORHIGHERSTRENGTHMARTENSITICSTAINLESSSTEELPLATESHEETANDSTRIP

链接地址:http://www.mydoc123.com/p-457185.html