ASD-STAN PREN 4700-005-2009 Aerospace series Steel and heat resisting alloys Wrought products Technical specification Part 005 Forging stock (Edition P 1)《航空航天系列 钢和耐热合金锻件的技术规范 第005.pdf

《ASD-STAN PREN 4700-005-2009 Aerospace series Steel and heat resisting alloys Wrought products Technical specification Part 005 Forging stock (Edition P 1)《航空航天系列 钢和耐热合金锻件的技术规范 第005.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4700-005-2009 Aerospace series Steel and heat resisting alloys Wrought products Technical specification Part 005 Forging stock (Edition P 1)《航空航天系列 钢和耐热合金锻件的技术规范 第005.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 4700-005 Edition P 1 July 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aer

2、ospace series Steel and heat resisting alloys Wrought products Technical specification Part 005: Forging stock Srie arospatiale Aciers et alliages rsistant chaud Produits corroys Spcification technique Partie 005 : Produits destins la forge Luft- und Raumfahrt Stahl und Hochwarmfesten Legierungen Um

3、geformte Erzeugnisse Technische Lieferbedingungen Teil 005: Schmiede Vormaterial This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Ae

4、rospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-

5、identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members

6、 have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 July 2009 Comments should be sent within six months after the date of publication to ASD-STAN Met

7、allic Material Domain Copyright 2009 by ASD-STAN prEN 4700-005:2009 (E) 2 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .5 4 Wording of order5 5 Health and safety .5 6 Technical requirements 5 Foreword This standard was reviewed by the Domain Tech

8、nical Coordinator of ASD-STANs Metallic Material Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4700-005:2009 (E) 3 Introduction This standard is part of the

9、 series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of steel and heat resisting alloy forging stock. It sh

10、all be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the e

11、dition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3651-1, Determination of resistance to intergranular corrosion of stainless steels Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test i

12、n nitric acid medium by measurement of loss in mass (Huey test). ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels Corrosion test in media containing sulfuric acid. ISO 3887, Steels De

13、termination of depth of decarburization. EN ISO 6507-1, Metallic materials Vickers hardness test Part 1: Test method. EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method. EN ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Tes methodt (scales A, B, C, D, E, F, G,

14、 H, K, N, T). EN 2002-1, Aerospace series Metallic materials Test methods Part 1: Tensile testing at ambient temperature. EN 2002-2, Aerospace series Metallic materials Test methods Part 2: Tensile testing at elevated temperature. EN 2002-5, Aerospace series Test methods for metallic materials Part

15、5: Uninterrupted creep and stress-rupture testing. EN 2002-7, Aerospace series Metallic materials Test methods Part 7: Hardness test.1)EN 2002-16, Aerospace series Metallic materials Test methods Part 16: Non-destructive testing Penetrant testing. 1)EN 2003-2, Aerospace series Steels Test methods Pa

16、rt 2: Izod impact test.1)1) Published as ASD Prestandard at the date of publication of this standard. prEN 4700-005:2009 (E) 4 EN 2003-7, Aerospace series Steel Test methods Part 7: Macrographic test.1)EN 2003-14, Aerospace series Test methods for steel products Part 14: Hardenability test by end qu

17、enching (Jominy test).1)EN 2032-1, Aerospace series Metallic materials Part 1: Conventional designation. EN 2032-2, Aerospace series Metallic materials Part 2: Coding of metallurgical condition in delivery condition. EN 2078, Aerospace series Metallic materials Manufacturing schedule, inspection sch

18、edule, inspection and test report Definition, general principles, preparation and approval. EN 2950, Aerospace series Test method wrought heat resisting alloys Semi-finished products and parts Conditions for macrographic and micrographic examination Atlas of structures and defects. EN 2951, Aerospac

19、e series Metallic materials Test method Micrographic determination of content of non-metallic inclusions.1)EN 3874, Aerospace series Test methods for metallic materials Constant amplitude force-controlled low cycle fatigue testing.1)EN 3987, Aerospace series Test method for metallic materials Consta

20、nt amplitude force-controlled high cycle fatigue testing.1)EN 3988, Aerospace series Test methods for metallic materials Constant amplitude strain-controlled low cycle fatigue testing.1) EN 4050-1, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates, forging sto

21、ck and forgings Part 1: General requirements.1)EN 4050-4, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates, forging stock and forgings Part 4: Acceptance criteria. 1) EN 4258, Aerospace series Metallic materials General organization of standardization Links b

22、etween types of EN standards and their use. EN 4259, Aerospace series Metallic materials Definition of general terms.1)EN 4436, Aerospace series Steel Test methods Determination of Delta ferrite content.1)EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and

23、Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994). EN 9133, Aerospace series Quality management systems Qualification Procedure for aerospace standard parts. EN 10027-1, Designation systems for steels Part 1: Steel nam

24、es. EN 10045-1, Metallic materials Charpy impact test Part 1: Test method. prEN 4700-005:2009 (E) 5 EN 10079, Definition of steel products. ASTM E709, Standard Guide for Magnetic Particle Testing. 2)ASTM E1444, Standard Practice for Magnetic Particle Testing. 2)AMS 2750, Pyrometry.2)3 Terms and defi

25、nitions For the purposes of this document, the terms and definitions given in EN 4259 apply. For definitions specific to steel, see EN 10079. 4 Wording of order The order shall clearly indicate: quantities to be supplied; dates of delivery; material standard number; delivery condition and metallurgi

26、cal code of products; dimensions and tolerances or reference to an appropriate dimensional standard; product designation, when required; forwarding address; nature and type of packing, if required; surface protection, if appropriate; definition and frequency of any special tests and their retest pro

27、cedures, if required. 5 Health and safety Products in the delivery condition shall fulfil the health and safety laws of the area of the country when and where it is to be delivered. A product safety data sheet shall be available. 6 Technical requirements 6.1 General The product shall be manufactured

28、 in accordance with the requirements of the relevant material standard and the applicable requirements of this specification. A manufacturing schedule shall be established and applied in accordance with EN 2078. 2) Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Driv

29、e, PO Box C700, West Conshohocken, PA, 19428-2959 USA. prEN 4700-005:2009 (E) 6 Product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product. Notwithstanding previous acceptance com

30、plying with this material standard, any product that is found, at a later stage, to contain such defects shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclus

31、ive) of the material standard and Table 2 relates to lines 30 onwards in which the subline format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is not shown in Tables 1 and 2, the requirement

32、 is stated in the material standard and/or order. The requirements of the order and/or material standard shall over-ride the requirements of the technical specification. 6.2 Qualification requirements Qualification requirements when invoked by the material standard and/or order are detailed in Table

33、s 1 and 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase shall be run on the first 3 batches, coming from at least 2 casts. 6.3 Release requirements 6.3.1 Release tests Release testing shall be the responsibility of the manufacturer. The purchaser reserves th

34、e right to perform any of the inspections and/or tests required by the material standard and/or order. The test samples shall be representative of the product. When required on the order, the manufacturer shall inform the purchaser of the planned dates for extraction of samples and release testing i

35、n order that these operations may be witnessed. Tables 1 and 2 detail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particular inspection and/or test for release shall be carried out if corresponding acceptance criteria and/or va

36、lues are stated in the applicable material standard, but see also in 6.3.5. 6.3.2 Retests If any requirement is not met, retests shall be carried out under the following conditions unless otherwise stated in the material standard or order. If the test procedure or test piece preparation is faulty, t

37、esting shall be re-applied at the original frequency after rectification of the original cause of failure, on a test sample located near the first one. When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall be selected at twice the original frequen

38、cy from the product, one of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer after suitable identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If one or more tests are unsatisfactory

39、, the batch shall be: rejected, or 100 % retested and the conforming products accepted, or prEN 4700-005:2009 (E) 7 partially or fully re-heat treated if heat treatment can rectify the cause of the failure and tested as a completely new batch except for chemical composition and cleanness inspection.

40、 The reheat treatment shall be stated on the release test certificate. For cleanness inspection, if the material fails the requirement the product may be cut back before retesting. 6.3.3 Rejection Any failure to meet the requirements of the material standard shall be cause for rejection. 6.3.4 Speci

41、al tests Special tests may be required by the purchaser. In such cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule and shall be mutually agreed by the manufacturer and purchaser. 6.3.5 Capability clause Where the capabi

42、lity clause is invoked and where sufficient statistical evidence exists, the test need not be carried out (unless specifically requested by the purchaser). However, this in no way reduces the obligations of the manufacturer to fulfil the requirements. If subsequent testing indicates that the product

43、 does not comply with the requirements, the batch shall be rejected. 6.3.6 Statistical process control Reduction in the extent of release testing, other than that defined in 6.3.4 above, may be negotiated with the purchaser on the basis of appropriate statistical process control and/or statistical d

44、ata. 6.3.7 Inspection and test report The manufacturer shall furnish, with each delivery, a report conforming to the requirements of EN 2078 stating the following: manufacturers name and address and, if appropriate, identification of the plant; order number; material standard number; delivery condit

45、ion and metallurgical code of the product; quantity and dimensions; manufacturing and inspection schedule reference; cast and batch number; batch and/or test samples heat treatment conditions; results of the tests and retests if any. 6.4 Traceability Each product shall be traceable to the cast, prod

46、uction batch and/or heat treatment batch at all stages of manufacture, testing and delivery. prEN 4700-005:2009 (E) 8 Table 1 Technical requirements for lines 1 to 29, where appropriate Frequency of testing Material standard line reference No. Title Requirements Qualification Release 1 Material desi

47、gnation EN 2032-1 and EN 10027-1 if applicable 2 Chemical composition The chemical composition of the alloy shall comply with requirements of the material standard. The samples taken for analysis shall be representative of the melt. The method of analysis shall be at the option of the manufacturer,

48、but in cases of dispute, the reference method set out in the relevant EN or ISO standard shall be used. If no EN or ISO standard exists, a fundamental and agreed method of chemical analysis calibrated against accepted reference standards shall be used. In the case of remelted material (VAR or ESR),

49、samples shall be taken from the bottom or the top of one ingot or ingot product. An analysis shall be made of each sample and certificates of analysis shall be supplied to the purchaser. The elements to be determined shall be as required by the material standard or as agreed between the manufacturer and the purchaser. Elements not quoted in the material standard shall not be inte