ASD-STAN PREN 4530-001-2005 Aerospace Series Sealing Sleeves Used in Elements of Connection Part 001 Technical Specification (Edition P1)《航空航天系列 连接部件用密封套 第001部分 技术规范 第P1版》.pdf
《ASD-STAN PREN 4530-001-2005 Aerospace Series Sealing Sleeves Used in Elements of Connection Part 001 Technical Specification (Edition P1)《航空航天系列 连接部件用密封套 第001部分 技术规范 第P1版》.pdf》由会员分享,可在线阅读,更多相关《ASD-STAN PREN 4530-001-2005 Aerospace Series Sealing Sleeves Used in Elements of Connection Part 001 Technical Specification (Edition P1)《航空航天系列 连接部件用密封套 第001部分 技术规范 第P1版》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication 28 February 2005 prEN 4530-001 Edition P 1 February 2005 Comments should be sent within six months after the date of publication to AECMA-STAN PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulled
2、elle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.org ICs: 49.060 Descriptors: ENGLISH VERSION Aerospace series Sealing sleeves used in elements of connection Part O01 : Technical specification Srie arospatiale Manchons dtanchit utiliss dans les organes de conn
3、exion Partie O01 : Spcification technique Luft- und Raumfahrt Dichtungshlse zur Verwendung in Verbindungselementen Teil O01 : Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association d Aerospace Industries - S
4、tandardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interc
5、hangeability is affected, physically or functionally, without wdentification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transfo
6、rmation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Electrical Domain I I Copyright 2005 O by AECMA-STA1 Page 2 prEN 4530
7、01:2005 Fore wo rd This standard was reviewed by the Domain Technical Coordinator of AECMA-STANS Electrical Domain . After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA-STANS General Process Manual. this standard has received approval for Publication . C
8、ontents 1 2 3 4 5 6 7 8 9 10 11 12 13 Scope Normative references Terms and definitions . Conditions of use and temperature classes . Design and description Dimensions and mass . Operation . Tests Quality assurance . Designation and marking . Delivery condition . Packaging . Storage Page 3 3 3 3 4 4
9、4 4 7 a 9 9 9 Page 3 prEN 453001:2005 1 Scope This standard specifies: - the electrical, mechanical, environmental and dimensional characteristics of sealing sleeves used in elements of connection; - the conditions for qualification if the sealing sleeves are not tested during the connector qualific
10、ation, acceptance testing and quality assurance; - the test programme and groups. It is applicable to removable sealing sleeves used in connectors or in other elements of electrical connection. 2 Normative refe re nces The following referenced documents are indispensable for the application of this
11、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO2859-1, Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) f
12、or lot-by lot inspection. EN 2591-loo*, Aerospace series - Elements of electrical and optical connection - Test methods - Part 100: General. EN 91 33, Aerospace series - Quality management systems - Qualification procedure for aerospace standard parts. MI L-HDBK-454, General Guidelines for Electroni
13、c Equipment. *) 3 Terms and definitions For the purposes of this document, the terns and definitions given in EN 2591-100 and the following apply. 3.1 sealing sleeve device to prevent the ingress of contaminants and to facilitate the insertion and extraction of the contact 4 Conditions of use and te
14、mperature classes The sealing sleeves specified shall be from one of the classes specified below: - class P: maximum operating temperature 125 OC; - class R: maximum operating temperature 150 OC; - class S: maximum operating temperature 200 OC; - class T: maximum operating temperature 260 OC; - clas
15、s U: maximum operating temperature 350 OC. The minimum operating temperature shall be - 65 OC, unless otherwise specified in the product standard. * And all parts quoted in this standard. 1) Published as AECMA Prestandard at the date of publication of this standard. 2) Published by Department of Def
16、ense (DOD), the Pentagon, Washington, DC 20301, USA. Page 4 prEN 453001:2005 5 Design and description Refer to the relevant product standard 6 Dimensions and mass The dimensions of the sealing sleeves and their mass are defined in the product standard. 7 Ope rati on The assembly procedure of the sea
17、ling sleeves is defined in the product standard. 8 Tests See Table 1. Table 1 EN 2591- Test Details 101 Visual examination Initial examination: before and after wiring Details to be examined: - identification of materials in accordance with definition document; - identification; - aspect before and
18、after wiring; - marking; - surface roughness. In accordance with the product standard 102 Examination of dimensions and mass 201 Contact resistance - low level Contact resistance at rated current Not applicable Not applicable 202 203 Electrical continuity at microvolt level Discontinuity of contacts
19、 in the microsecond range Not applicable Not applicable 204 205 Housing (shell) electrical continuity Measurement of insulation resistance Not applicable In accordance with the product standard 206 207 Voltage proof test Temperature rise due to rated current In accordance with the product standard N
20、ot applicable 208 209 Current temperature derating Electrical overload Not applicable 21 o Not applicable 21 1 Capacitance Surface transfer impedance Not applicable 21 2 Not applicable 21 3 Shielding effectiveness from 1 O0 MHz to 1 GHz Not applicable continued Page 5 prEN 453001:2005 EN 2591- Table
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASDSTANPREN45300012005AEROSPACESERIESSEALINGSLEEVESUSEDINELEMENTSOFCONNECTIONPART001TECHNICALSPECIFICATIONEDITIONP1

链接地址:http://www.mydoc123.com/p-453214.html