ANSI INCITS ISO 5654-1-1984 Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad 1 9 tpmm (48 tpi) on .pdf

《ANSI INCITS ISO 5654-1-1984 Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad 1 9 tpmm (48 tpi) on .pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO 5654-1-1984 Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad 1 9 tpmm (48 tpi) on .pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 INCITS/ISO 5654-1:19842010 (ISO 5654-1:1984, IDT) Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad, 1,9 tpmm (48 tpi), on one side - Part 1 : Dimensional, physical and magnetic characteristics Reaffirmed as INCITS/ISO

2、 5654-1:1984 R2015INCITS/ISO 5654-1:19842010 PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perfo

3、rming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PD

4、F file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central S

5、ecretariat at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 10/6/2010 Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2010

6、by Information Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Indust

7、ry Council (ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1101 K Street NW, Suite 610, Washington DC 20005. P

8、rinted in the United States of America ii ITIC 2010 All rights reserved Contents 0 Introduction . 1 Scope and field of application 2 References 3 Definitions 4 General description. 4.1 Generalfigures 4.2 Mainelements 4.3 Description, 4.4 Optional features. . 5 General requirements . 5.1 Environment

9、and transportation . 5.2 Materials . 5.3 Direction of rotation . 6 Dimensional characteristics 6.1 Jacket . 6.2 Liner 6.3 Disk . 7 Physical characteristics . . . . . . . . . . , . . . . . . . . . . . . . . . . . . . . . 7.1 Inflammability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10、 . . . . 7.2 Coefficient of linear thermal expansion of the disk . . . . . 7.3 Coefficient of linear hygroscopic expansion of the disk . 7.4 Opacity. 7.5 Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 1

11、 1 2 2 2 2 2 2 2 3 3 3 3 4 4 iii 6 Magnetic characteristics 6.1 Track geometry . 6.2 Functional testing . Annexes A Measurement of light transmittance . . . B Measurement of the cartridge thickness . . . . C Method for measuring the effective track width D Write-inhibit notch. . . . 11 14 16 17 INTE

12、RNATIONAL STANDARD IS0 5654/l-1982 (El Information processing - Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad, I,9 tpmm (48 tpi), on one side - Part 1 : Dimensional, physical and magnetic characteristics 0 Introduction IS0 5654 specifies th

13、e characteristics of 200 mm (8 in) flexible disk cartridges recorded at 13 262 ftprad on one side using two-frequency recording. IS0 5654/2 specifies the quality of recorded signals, track layout, and the track format. Together with the labelling scheme specified in IS0 7665, IS0 5654/l and IS0 !X54

14、/2 provide for full data interchange between data processing systems. 1 Scope and field of application This part of IS0 5654 specifies the dimensional, physical and magnetic characteristics of the cartridge, so as to provide physical interchangeability between data processing systems. NOTE - Numeric

15、 values in the SI and/or Imperial measurements system in this International Standard may have been rounded and therefore are consistent with, but not exactly equal to, each other. Either system may be used, but the two should be neither intermixed nor reconverted. The original design was made using

16、the Imperial measurement system. 2 References IS0 646, information processing - 7-bit coded character set for information interchange. 1) IS0 2022, Information processing - /SO 7-bit and B-bit coded character sets - Code extension techniques.2) IS0 4873, Information processing - g-bit coded characte

17、r set for information interchange. IS0 7665, Information processing - File structure andlabelling of flexible disk cartridges for information interchange. 3) 3 Definitions For the purpose of this International Standard, the following definitions apply : 3.1 flexible disk : Flexible disk which accept

18、s and retains, on the specified side or sides magnetic signals intended for input/output and storage purposes of information data pro- cessing and associates systems. 3.2 reference flexible disk cartridge : Flexible disk car- tridge arbitrarily selected for a given property for calibrating purposes.

19、 3.3 secondary reference flexible disk cartridge : Flexible disk cartridge intended for routine calibrating purposes, the performance of which is known and stated in relation to that of the reference flexible disk cartridge. 3.4 signal amplitude reference flexible disk cartridge : Reference flexible

20、 disk cartridge selected as a standard for recording field and signal amplitude. NOTE - A master standard for signal amplitudes, reference fields, overwrite and resolution characteristics has been established by the Physikalisch-Technische Bundesanstalt (PTB), Bundesallee 190, in Braunschweig, Germa

21、ny. Secondary reference flexible disk cartridges can be ordered from PTB under part number RM 5654 as long as available. 3.5 typical field : The minimum recording field which, when applied to a flexible disk cartridge, causes a signal output equal to 95 % of the maximum average signal amplitude when

22、 taken as a function of the recording field at the specified track and flux transition frequency of that flexible disk cartridge. 3.6 reference field : The typical field of the signal amplitude reference flexible disk cartridge. 1) At present at the stage of draft. (Revision of IS0 646-1973.) 2) At

23、present at the stage of draft. (Revision of IS0 2022-1973.) 3) At present at the stage of draft. 1 IS0 5554/l-1982 (E) 3.7 test recording currents : The two recording currents between 145 % and 155 % of the currents which produce the reference field at 250 OKI flux transitions per second (ftps) on t

24、rack 06 and track 76 respectively. The first of these currents shall be used for recording on tracks 00 to 43. The second cur- rent shall be used for recording on tracks 44 to 76 (see also 8.21. 3.9 standard reference amplitudes : The average signal amplitudes derived from the signal amplitude refer

25、ence flexible disk cartridge at the density obtained when writing with 250 000 ftps on track 00 and with 500 OCMI ftps on track 76 using the appropriate test recording current for the track under test (see also 8.2). 3.9 average signal amplitude : The arithmetically- averaged value for a track of th

26、e output voltage measured peak-to-peak over the whole track. 3.10 in contact : An operating condition in which the magnetic surface of the disk intended for data storage is in physical contact with the magnetic head. 3.11 formatting : Writing the proper control information establishing the 77 physic

27、al tracks and designating the addresses of physical records on the flexible disks surfaces. 3.12 initialization : Writing of the volume label, the ERMAP label, and any other information initially required to be on the flexible disk cartridge prior to the commencement of general processing or use. 3.

28、13 recording area : That area of the disk surface with which the head may come into contact. 4 General description 4.1 General figures A typical flexible disk cartridge is represented in figures 1 to 3 as follows : - figure 1 shows the cartridge seen from above, side 0 up; - figure 2 shows section A

29、-A which is a cross-section along the line A-A in figure 1; - figure 3 shows a protective envelope with cartridge, side 1 up. 4.2 Main elements The main elements of this flexible disk cartridge are : - the recording disk; - the liner; - the jacket. The cartridge is stored in an envelope. 4.3 Descrip

30、tion The jacket is of a square form. It includes a central window, an index window and a head window in both sides. The liner is fixed to the inside of the jacket. It comprises two sheets of material between which the disk is held. The liner has the same openings as the jacket. The disk has only a c

31、entral hole and an index hole. 4.4 Optional features The interchange characteristics of the jacket allow for varia- tions of its contruction. It may include flaps, (for example, three flaps as shown in the drawings, or none), and notches along the reference edge. For conditions under which a write-

32、inhibit notch may be used, see annex D. 5 General requirements 5.1 Environment and transport 5.1.1 Testing environment Tests and measurements made on the cartridge to check the re- quirements of this International Standard shall be carried out under the following conditions : - temperature : 23 f 2

33、OC (73 + 4 OF); - relative humidity : 40 to 66 %; - conditioning before testing : 24 h minimum. The temperature and the relative humidity shall be measured in the air immediately surrounding the cartridge. The stray magnetic field at any point on the disk surface, including that resulting from the c

34、oncentrating effect of the recording head shall not exceed 4 Ooo A/m (50 Oe). 5.1.2 Operating environment Cartridges used for data interchange shall be operated under the following conditions : - temperature : 10 to 50 C (56 to 122 OF); - relative humidity : 20 to 60 %; - wet bulb temperature : n be

35、ing the numeric value corresponding to track number : n = 0 to 76. 5 IS0 5654/l-1982 (El 8.1.3.2 Track location tolerance - not less than 80 % on track 76 using 2f; For testing purposes, the centrelines of tracks recorded shall be within k 0,025 mm (k 0.001 in) of the nominal positions, when measure

36、d in the testing environment (see 5.1 .l). 8.1.4 Track number The track number shall be a two-digit decimal number (00 to 76) which identifies the tracks consecutively, starting at the outer- most track NIO). 8.1.5 Index The index is the point which determines the beginning and the end of a track. A

37、t the instant of having detected the leading edge of the index hole, the index is under the read-write gap. 8.2 Functional testing For the purposes of the following tests, the same drive unit shall be used for the writing and reading operations. 8.2.1 Surface tests The magnetic properties of the dat

38、a surface are defined by the testing requirements given below. 8.2.1 .l Test conditions The disk shall be tested at 360 f 7 rev/min. The test frequen- cies used shall be : of the appropriate standard reference amplitude. 8.2.1.4 Resolution On track 76, after recording with the appropriate test recor

39、ding current, the ratio average signal amplitude using 2f average signal amplitude using lf shall be greater than 60 % of the value of the same ratio for the signal amplitude reference flexible disk cartridge. 8.2.1.5 Overwrite On track 00, after recording with the appropriate test recording current

40、, first using lf and then overwriting using 2f for one revolution, the ratio residual average signal amplitude at lf after overwrite using 2f average signal amplitude after the first recording using lf shall be less than 100 % of the value of the same ratio for the signal amplitude reference flexibl

41、e disk cartridge. Measurements shall be made using a frequency-seiective voltmeter. 8.2.1.8 Modulation lf = 250000 k 250ftps Modulation shall be : 2f = 500 000 It 500 ftps and shall be used as specified for each test. 8.2.1.2 Typical field The typical field of the disk under test shall be within f 2

42、0 % of the reference field. It shall be measured using lf on tracks 00 and 76. 8.2.1.3 Average signal amplitude When a disk has been recorded with the test recording cur- rents, then read back on a system which has been calibrated by means of a signal amplitude reference flexible disk cartridge, rec

43、orded under the same conditions, the average signal amplitude of the disk under test shall be : - not more than 130 % on track 00 using If; maximum mean - minimum mean x 100% maximum mean + minimum mean The maximum mean shall be the average value of the amplitude-modulated output voltage in that par

44、t of the track with the maximum amplitudes, and the minimum mean shall be that in the respective part with the minimum amplitudes. Out- put voltage shall be measured peak-to-peak; averaging shall be done over about 2 000 consecutive flux transitions. On track 00 using lf and on track using 2f, modul

45、ation shall be less than 10 %. 8.2.2 Track quality test These tests shall be carried out using 2f and over all 77 usable tracks at the defined positions. The test recording currents shall be used. IS0 5654/l-1982 (E) 8.2.2.1 Missing pulse 8.2.3 Rejection criteria Write a track at 2f with the appropr

46、iate test recording current. Any playback signal, when measured base-to-peak which is less than 40 % of half the arithmetically averaged values of the output voltages measured peak-to-peak over the preceeding 2 000 consecutives flux transitions, shall be a missing pulse. 8.2.2.2 Extra pulse Write a

47、track at 2f with the appropriate test recording current. Erase for one revolution with a constant direct current equivalent to the quiescent value of the test recording current. Any playback signal, which when measured base-to-peak, in- cluding the statistical noise and the residual signal of the di

48、sk exceeds 30 % of half the average signal amplitude of the track under test, shall be an extra pulse. 8.2.3.1 Defective track A track on which one or more missing or extra pulses are detected in the same position(s) on consecutive passes shall be a defective track. The applicable number of consecut

49、ive passes shall be a matter of agreement between interested parties. 8.2.3.2 Requirements for tracks As initially received from the media supplier, cartridges shall have no defective tracks. 8.2.3.3 Rejected cartridge A cartridge which does not meet the requirements of 8.2.3.2 shall be rejected. Index window Central hole Figure 1 - Flexible disk cartridge Side 0 Jacket Disk Head window Liner Disk Flap Liner Jacket Figure 2 - Section A-A 7 605654/l-1982(E) Label area Side 1 Envelope Figure 3 - Pr