BS ISO 8051-2016 en_5555 Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with recess《标称直径从M3至M10的长柄丝锥.带凹槽的直径柄丝锥》.pdf

《BS ISO 8051-2016 en_5555 Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with recess《标称直径从M3至M10的长柄丝锥.带凹槽的直径柄丝锥》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 8051-2016 en_5555 Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with recess《标称直径从M3至M10的长柄丝锥.带凹槽的直径柄丝锥》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 8051:2016 Long shank taps with nominal diameters from M3 to M10 Full-diameter shank taps with r e c e s s BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 8051:2016 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO

2、 8051:2016. It supersedes BS ISO 8051:1999 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This

3、 publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 77001 2 ICS 25.100.50 Compliance with a British Standard cannot confe

4、r immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2016. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 8051:2016 ISO 2016 Long shank taps with nominal diameters from M3 to

5、M10 Full- diameter shank taps with recess Tarauds machine, queue longue, de diamtre nominal M3 M10 Tarauds queue pleine, gorge INTERNATIONAL STANDARD ISO 8051 Third edition 2016-09-15 Reference number ISO 8051:2016(E)BS ISO 8051:2016ISO 8051:2016(E)ii ISO 2016 All rights reserved COPYRIGHT PROTECTED

6、 DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior wr

7、itten permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 8

8、051:2016ISO 8051:2016(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensions . 1 4 Marking 2 Annex A (informative) Relationship between designations in this International Standard and ISO 13399 . 3 Bibliography 4 ISO 2016 All rights reserved iii Contents PageBS ISO 8051:2016ISO 8051:2016(E)

9、 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a

10、technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matter

11、s of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This docu

12、ment was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all s

13、uch patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and d

14、oes not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: w

15、ww.iso.org/iso/foreword.html. The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 2, Holding tools, adaptive items and interfaces. This third edition cancels and replaces the second edition (ISO 8051:1999), of which it constitutes a minor revision with the followin

16、g change: addition of Annex A, which gives the relationship between the designations of this International Standard and the ISO 13399 series.iv ISO 2016 All rights reservedBS ISO 8051:2016INTERNATIONAL ST ANDARD ISO 8051:2016(E) Long shank taps with nominal diameters from M3 to M10 Full-diameter sha

17、nk taps with recess 1 Scope This International Standard specifies the dimensions for full-diameter shank taps with recess with nominal diameters from M3 to M10 and thus complements ISO 2283, which concerns relieved shank taps. It applies to long shank machine taps. Technical specifications for taps

18、covered by this International Standard (including marking) are given in ISO 8830. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For unda

19、ted references, the latest edition of the referenced document (including any amendments) applies. ISO 529:1993, Short machine taps and hand taps ISO 8830:1991, High-speed steel machine taps with ground threads Technical specifications 3 Dimensions Dimensions are given in Figure 1 and Table 1. The th

20、readed lengths of these taps are in accordance with those given in ISO 529. Shank lengths (L l) are increased by 50 % with respect to those given in ISO 529; total lengths therefore vary accordingly. NOTE Annex A gives the relationship between the designations of this International Standard and ISO

21、13399 (all parts). Figure 1 ISO 2016 All rights reserved 1BS ISO 8051:2016ISO 8051:2016(E) Table 1 Designation d Pitch d 1 l L d 2 a l 3 Square Coarse pitches Fine pitches nom. coarse f i ne h9 b max. h16 min. a h11 c l 2 0,8 M3 M3 0,35 3 0,5 0,35 3,15 11 66 2,12 18 2,5 5 M3,5 M3,5 0,35 3,5 0,6 3,55

22、 13 68 2,5 20 2,8 M4 M4 0,5 4 0,7 0,5 4 73 2,8 21 3,15 6 M4,5 M4,5 0,5 4,5 0,75 4,5 3,15 3,55 M5 M5 0,5 5 0,8 5 16 79 3,55 25 4 7 M5,5 0,5 5,5 5,6 17 84 4 26 4,5 M6 M6 0,75 6 1 0,75 6,3 19 89 4,5 30 5 8 M7 M7 0,75 7 7,1 5,3 5,6 M8 M8 1 8 1,25 1 8 22 97 6 35 6,3 9 M9 M9 1 9 9 7,1 36 7,1 10 M10 M10 1

23、10 1,5 10 24 108 7, 5 39 8 11 M10 1,25 1,25 aThe recess is optional at the manufacturers discretion. If the recess is not required, such taps shall have a thread length equal to ll l / . bIn accordance with ISO 237, tolerance h9 applies to precision shanks; for non-precision shanks, the tolerance is

24、 h11. cIn accordance with ISO 237, the tolerance is enlarged to h12 when including errors of form of the square and of its position in relation to the shank. 4 Marking Marking shall be in accordance with ISO 8830.2 ISO 2016 All rights reservedBS ISO 8051:2016ISO 8051:2016(E) Annex A (informative) Re

25、lationship between designations in this International Standard and ISO 13399 For the relationship between designations in this International Standard and preferred symbols according to ISO 13399, see Table A.1. Table A.1 Relationship between designations in this International Standard and ISO 13399

26、Symbol in ISO 8051 Reference in ISO 8051 Property name in ISO 13399 series Symbol in ISO 13399 series Reference in ISO 13399 series d Figure 1 Table 1 Thread diameter TD 71E02C5C2EED3 d 1 Figure 1 Table 1 Connection diameter machine side DCONMS 71EBDBF5060E6 d 2 Figure 1 Table 1 Neck diameter DN 71E

27、AC48EC5DE0 l Figure 1 Table 1 Thread cutting part length THL 71E02C65BB9DA l 3 Figure 1 Table 1 Usable length LU 71EBB33490FDA L Figure 1 Table 1 Overall length OAL 71D078EB7C086 ISO 2016 All rights reserved 3BS ISO 8051:2016ISO 8051:2016(E) Bibliography 1 ISO 237, Rotating tools with parallel shank

28、s Diameters of shanks and sizes of driving squares 2 ISO 2283, Long shank taps with nominal diameters from M3 to M24 and 1/8 in to 1 in Reduced shank taps 3 ISO 13399 (all parts), Cutting tool data representation and exchange4 ISO 2016 All rights reservedBS ISO 8051:2016BS ISO 8051:2016ISO 8051:2016

29、(E) ISO 2016 All rights reserved IC S 25.100.50 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and

30、other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embod

31、ied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your or

32、ganization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards,

33、 through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Copyright in BSI publications All the content in BSI publications, including B

34、ritish Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Save for the provisions below, you

35、 may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent. Storing and using standards Standards pur

36、chased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any

37、 one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy

38、. This includes scanning of the document. If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions). Reproducing extracts For permission to reproduce content from BSI publicatio

39、ns contact the BSI Copyright & Licensing team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and a

40、dopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format,

41、 by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, ple

42、ase visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .

43、 Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledg

44、e Centre. Useful Contacts Customer Services Tel: +44 345 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 345 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK BSI Back Cover.indd 1 27/01/2016 14:20