BS ISO 6519-2015 en_2649 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机.喷油泵.轴端和毂盘的锥度》.pdf

《BS ISO 6519-2015 en_2649 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机.喷油泵.轴端和毂盘的锥度》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6519-2015 en_2649 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs《柴油机.喷油泵.轴端和毂盘的锥度》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 6519:2015 Diesel engines Fuel injection pumps Tapers for shaft ends and hubsBS ISO 6519:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6519:2015. It supersedes BS ISO 6519:2004 which is withdrawn. The UK participation in

2、 its preparation was entrusted to Technical Committee MCE/22, Engines for road vehicles. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible f

3、or its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 83388 5 ICS 43.060.40 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards

4、Policy and Strategy Committee on 31 July 2015. Amendments issued since publication Date Text affectedBS ISO 6519:2015 ISO 2015 Diesel engines Fuel injection pumps Tapers for shaft ends and hubs Moteurs diesels Pompes dinjection de combustible Cnes pour bouts darbre et moyeux INTERNATIONAL STANDARD I

5、SO 6519 Fourth edition 2015-08-15 Reference number ISO 6519:2015(E)BS ISO 6519:2015ISO 6519:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilize

6、d otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright

7、office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 6519:2015ISO 6519:2015(E)Foreword iv 1 Scope . 1 2 Dimensions and tolerances . 1 2.1 General . 1 2.2 Shaft ends with taper 1 2.3 Keyways of hub with ta

8、per . 1 ISO 2015 All rights reserved iii Contents PageBS ISO 6519:2015ISO 6519:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out t

9、hrough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO colla

10、borates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approv

11、al criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the su

12、bject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any tr

13、ade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the

14、Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 34, Propulsion, powertrain, and powertrain fluids. This fourth edition cancels and replaces the third edition (ISO 65

15、19:2004), which has been technically revised.iv ISO 2015 All rights reservedBS ISO 6519:2015INTERNATIONAL ST ANDARD ISO 6519:2015(E) Diesel engines Fuel injection pumps Tapers for shaft ends and hubs 1 Scope This International Standard specifies the dimensions of tapered shaft ends and hubs of fuel

16、injection pumps and common-rail high pressure pumps for diesel (compression-ignition) engines. The specified shaft ends and hubs may be used with or without Woodruff keys. NOTE The specified shaft ends and hubs can also be used for other applications where no specific standards exist. 2 Dimensions a

17、nd tolerances 2.1 General To ensure satisfactory operation of the taper drive, it is necessary for manufacturers to provide such cone angle tolerances that the contact between the male and female cones commences at the major diameter. 2.2 Shaft ends with taper Shaft ends shall be as shown in Figure

18、1 and Table 1 or Figure 2 and Table 2. The shaft ends taper and thread (Figure 1) may be made optionally according to type 1 or 2. However, it shall be possible to screw the go-gauge for the thread up to the XX line for both these types. Type 3 is a configuration with the thread inside of the taper.

19、 This configuration saves space and avoids the critical interface between the taper and the thread of the configuration type 1 or 2. 2.3 Keyways of hub with taper Hub keyways shall be as shown in Figure 3 and Table 3. The length of the hub cone shall be such that, after assembling, the face at the s

20、maller diameter of the hub cone lies so far in front of the XX line (see Figure 1 and Figure 2) that the fixing nut can be correctly screwed up. Dimensions in millimetres a) Type 1 ISO 2015 All rights reserved 1BS ISO 6519:2015ISO 6519:2015(E) b) Type 2 Figure 1 Shaft ends type 1 and type 2 Table 1

21、Shaft ends type 1 and type 2 Dimensions in millimetres d a nom. d 1 l 1 max. l 2 0 -1 t 1 max. b (h9) 17 M12 1,75 14,5 18 1,6 3 , 20 M14 1,5 12 15 2 4 , 16,5 20 22 M14 1,5 16,5 20 2 4 , M16 1,5 b 18 23 M16 1,5 18 23 2 4 , 25 M18 1,5 15 25 2,6 5 , 20 30 M20 1,5 23 30 2,6 5 , 35 M24 1,5 19 27 2,6 5 ,

22、27 27 35 40 M30 1,5 27 27 2,6 5 , 40 aThe tolerance for dimension d depends on the type of shaft bearing. bThe thread M16 1,5 is preferred for shaft ends with 22 mm diameter.2 ISO 2015 All rights reservedBS ISO 6519:2015ISO 6519:2015(E) Key 1 internal thread 2 clamping collar (for manufacturing purp

23、oses only, no function at the engine) a Nominal. Figure 2 Shaft end type 3 Table 2 Shaft end type 3 Dimensions in millimetres d a nom. d 1 l 1 min. l 2 0 -1 l 3 b (h9) h 25 M12 1 22 25 19,75 4 , 9,45 aThe tolerance for dimension d depends on the type of shaft bearing.a Nominal. Figure 3 Hub ISO 2015

24、 All rights reserved 3BS ISO 6519:2015ISO 6519:2015(E) Table 3 Hub Dimensions in millimetres d a nom. t 2 min. b (D10) 17 1,8 3 , , 20 2,2 4 , , 22 2,2 4 , , 23 2,2 4 , , 25 2,8 (4 or 5) , , 30 2,8 5 , , 35 2,8 5 , , 40 2,8 5 , , ad is the nominal diameter of the shaft.4 ISO 2015 All rights reserved

25、BS ISO 6519:2015BS ISO 6519:2015ISO 6519:2015(E) ISO 2015 All rights reserved IC S 43.060.40 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorpor

26、ated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and

27、others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards t

28、o help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and do

29、wnload PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered fro

30、m our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European a

31、nd international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BS

32、I Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a

33、 Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our Br

34、itish Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyrig

35、ht All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such i

36、nformation to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written per

37、mission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW