ASTM D5959-12(2017) Standard Test Method for Bulk Density of Level Paintbrush Filaments.pdf

《ASTM D5959-12(2017) Standard Test Method for Bulk Density of Level Paintbrush Filaments.pdf》由会员分享，可在线阅读，更多相关《ASTM D5959-12(2017) Standard Test Method for Bulk Density of Level Paintbrush Filaments.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5959 12 (Reapproved 2017)Standard Test Method forBulk Density of Level Paintbrush Filaments1This standard is issued under the fixed designation D5959; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a procedure for measuring theweight of filaments per unit volume.1.2 This test method is applicable

3、only to monofilamentwith consistent longitudinal (level) profiles.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard d

4、oes not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This international standard wa

5、s developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Summary

6、of Test Method2.1 The weight and volume of a bundle of filaments ismeasured, and the bundle density is calculated.3. Significance and Use3.1 Filaments are available in a variety of cross sections andmaterials.Ameasure of bulk density permits the brushmaker toestimate the weight of filament required

7、to prepare a givennumber of brushes.4. Apparatus4.1 The apparatus requires some machining, and is as-sembled as shown in Fig. 1 from the following equipment:4.1.1 Air Valve24.1.2 Miniature Air Cylinder,3dual acting, heavy duty.4.1.3 Assorted parts shown in Fig. 1 are machined from 304stainless steel

8、 and assembled as shown along with the air valveand cylinder just described. The scale must be fixed in place sothat it reads accurately the diameters of metal standards that are1.82 in. (46.2 mm) and 2.06 in. (52.3 mm) diameter.4.2 Weighing Device, accurate to 0.1 g to weigh the bundle.4.3 Scale, a

9、ccurate to 0.02 in. (0.5 mm) to measure thebundle length.4.4 Air Supply, with pressure regulator set for 50 psig.4.5 Calibration Standards, 1.82 (46.2 mm) and 2.06 in.(52.3 mm) in diameter.45. Sampling, Test Specimens and Test Units5.1 The test result will depend on the cross-sectional shape,the pol

10、ymer, and the length of the bundle selected for the test.To a lesser extent it will also depend on the filament diametersince thin filaments pack more efficiently than large ones.5.2 The device, as pictured in Fig. 1, is designed to measurediameters ranging from 1.82 to 2.06 in. (46.2 to 52.3 mm).Ma

11、ke sure that both ends are measured and the results areaveraged.6. Procedure6.1 Select a sample of approximately 2-in. (50-mm) diam-eter. Filament may be removed from a sample so the bundlediameter falls within the scale range (1.82 to 2.06 in.) (46.2 to52.3 mm). One convenient method to adjust the

12、samplediameter to the desired range is to fill a 2-in. (50-mm) insidediameter tube. If the sample is too small, like samples may becombined to adjust the bundle diameter to the desired range.6.2 Weigh the sample bundle to the nearest 0.1 g (W). Makesure that the weight excludes the wrap or rubber ba

13、nds used tohold the filament together.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved June 1, 2017. Published June 20

14、17. Originallyapproved in 1996. Last previous addition approved in 2012 as D5959 12. DOI:10.1520/D5959-12R17.2Air valve such as Model 6676 available from Hunt Valve Co., 1913 E. StateStreet, Salem, Ohio 44460, or equivalent, has been found suitable for this purpose.3Miniature air cylinder such as Mo

15、del H95-5D,916-in. (14.3-mm) bore, 5-in.(127-mm) stoke, dual acting, heavy duty, available from Clippard InstrumentLaboratory, 7390 Colerain Road, Cincinnati, OH 45239, or equivalent, has beenfound suitable for this purpose.4Steel cylinders machined to diameters of 1.82 in. with a tolerance of 0.001

16、 in.(46.2 mm with a tolerance of 0.02 mm) and 2.060 in. with a tolerance of 0.001 in.(52.3 mm with a tolerance of 0.02 mm).Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with int

17、ernationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16.3 Measure the lengths of five individual fil

18、aments to thenearest 0.02 in. (0.5 mm) with a ruler and average the lengthsto determine bundle length (L).6.4 With rubber bands holding the bundle together, roll itbetween the palms of the hands four times and then place theend of the bundle inside the loop of measuring tape in thedevice shown in Fi

19、g. 1. Operate the air valve lever 10 times tostabilize. Actuate the air valve to tighten the steel tape. Readthe bundle diameter, estimating to the nearest 0.005 in. (0.1mm) from where the pointer indicates on the scale.6.5 Release the bundle. Reverse the bundle end for end andrepeat 6.4 to measure

20、the diameter of the opposite end.6.6 Average the results (D) and proceed to calculate the bulkdensity as described in 7.1. Bulk density is expressed in g/in.3,an accepted industry standard.7. Calculation or Interpretation of Results7.1 Calculate bulk density as follows:Bulk Density 5 4 3W/L 3 3D2! (

21、1)where:W = bundle weight, g,L = bundle length, in. (cm), andD = mean bundle diameter, in. (cm).8. Precision and Bias8.1 PrecisionMeasurements of bulk density of solid, levelfilament at five laboratories agreed within 60.2 g/in.3or 61%.Repeatability within the laboratory for four bundles was 60.1g/i

22、n.3for solid and 60.2 g/in.3for hollow.8.2 BiasSince there is no accepted reference materialsuitable for determining the bias for the procedure in this testmethod, no statement on bias can be made.9. Keywords9.1 bulk density; density; filaments; paint brushASTM International takes no position respec

23、ting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This sta

24、ndard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Internati

25、onal Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below

26、.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Apparatus to Measure Bundle DiameterD5959 12 (2017)2