IEEE C57.12.39-2017 Requirements for Distribution Transformer Tank Pressure Coordination.pdf

《IEEE C57.12.39-2017 Requirements for Distribution Transformer Tank Pressure Coordination.pdf》由会员分享，可在线阅读，更多相关《IEEE C57.12.39-2017 Requirements for Distribution Transformer Tank Pressure Coordination.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Standard for Requirements for Distribution Transformer Tank Pressure Coordination IEEE Std C57.12.39-2017 IEEE Power and Energy Society Sponsored by the IEEE Transformers Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C57.12.39-2017 IEEE Standard for Requirements for Distribut

2、ion Transformer Tank Pressure Coordination Sponsor IEEE Transformers Committee of the IEEE Power and Energy Society Approved 6 December 2017 IEEE-SA Standards BoardAbstract: Certain mechanical requirements relating to tank strength as well as static and dynamic tank pressure mitigation for liquid-im

3、mersed distribution transformers are covered in this standard. The electrical and mechanical requirements of any accessory devices that may be supplied with the transformer are not covered in this standard. It is intended to define the mechanical performance requirements to prevent permanent tank de

4、formation or rupture of distribution transformers covered under this standard. These requirements will provide a more standard design of transformer tank and associated components related with both static and dynamic pressure coordination. Keywords: distribution transformer, fault current, IEEE C57.

5、12.39, liquid preservation, PRD, pressure, pressure coordination, pressure relief, pressure relief device, pressure relief plug, pressure relief valve, PRV, rapid transient pressure, tank, tank deformation, tank rupture, withstand The Institute of Electrical and Electronics Engineers, Inc. 3 Park Av

6、enue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 4 May 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; a

7、nd quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence

8、 of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought

9、 about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any

10、 duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the

11、 appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

12、 CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE W AS FO

13、RESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Of

14、ficial statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal po

15、sition of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments

16、 for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a pro

17、posed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its so

18、cieties and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in

19、revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all ap

20、plicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the p

21、ublication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws. They are made available by IEEE and

22、 are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by pub

23、lic authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2018 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard f

24、or company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual stan

25、dard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to tim

26、e through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every 10 years. When a d

27、ocument is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standa

28、rd. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For more information about th

29、e IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html. Users are encouraged to

30、check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any p

31、atent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Letters of Assurance may indi

32、cate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claim

33、s may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or condi

34、tions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is en

35、tirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2018 IEEE. All rights reserved. Participants At the time this IEEE standard was completed, the C57.12.39 Working Group had the following membership: Carlos Gaytan, Chair Jeremy V an H

36、orne, Secretary Omar Ahmed Adam Bromley John Chisholm Anil Dhawan Ali Ghafourian Said Hachichi Joshua Herz Justin Pezzin Brian Klaponski Alejandro Macias Michael Miller Charles Morgan Daniel Mulkey Jerry Murphy Dwight Parkinson George Payerle Martin Rave Stephen Shull Charles Simmons Edward Smith Ro

37、nald Stahara Christopher Sullivan Giuseppe Termini Alan Traut Reinaldo V alentin Alan Wilks The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Omar Ahmed Thomas Barnes Wallace Binder Thomas Blackburn

38、Paul Cardinal John Crouse Jean-Bernard Dastous Gary Donner William Elliott Michael Faulkenberry Marcel Fortin Fredric Friend Carlos Gaytan Edwin Goodwin Randall Groves Said Hachichi John Harley Jeffrey Hartenberger Jeffrey Helzer William Henning Joshua Herz Werner Hoelzl Gary Hoffman Thomas Holifiel

39、d Richard Jackson John John Gael Kennedy Sheldon Kennedy Jim Kulchisky Chung-Yiu Lam Benjamin Lanz Aleksandr Levin Richard Marek Lee Matthews William McBride Daleep Mohla Charles Morgan Daniel Mulkey Jerry Murphy K. R. M. Nair Lorraine Padden Mirko Palazzo Bansi Patel Dhiru Patel Branimir Petosic Ch

40、ristopher Petrola Justin Pezzin Jim Phillips Alvaro Portillo Martin Rave Thomas Rozek Ryandi Ryandi Daniel Sauer Bartien Sayogo Stephen Schroeder Stephen Shull Hyeong Sim Jeremy Smith Jerry Smith Steve Snyder Ronald Stahara Alan Traut Roger V erdolin John V ergis Kenneth White Alan Wilks William Wim

41、mer7 Copyright 2018 IEEE. All rights reserved. When the IEEE-SA Standards Board approved this standard on 6 December 2017, it had the following membership: Jean-Philippe Faure, Chair Gary Hoffman, Vice Chair John D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald C. Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Y u Y uan *Member Emeritus