IEEE 776-1992 - IEEE Recommended Practice for Inductive Coordination of Electric Supply and Communication Lines.pdf

《IEEE 776-1992 - IEEE Recommended Practice for Inductive Coordination of Electric Supply and Communication Lines.pdf》由会员分享，可在线阅读，更多相关《IEEE 776-1992 - IEEE Recommended Practice for Inductive Coordination of Electric Supply and Communication Lines.pdf（59页珍藏版）》请在麦多课文档分享上搜索。

1、Copyright 1998 IEEE All Rights Reserved 1IEEE Std 776-1992 (R2008)(Revision of IEEE Std 776-1987)IEEE Recommended Practice for Inductive Coordination of Electric Supply and Communication LinesSponsorTransmission Systems Committeeof theIEEE Communications SocietyReaffirmed September 25, 2008Approved

2、December 3, 1992IEEE Standards BoardAbstract: The inductive environment that exists in the vicinity of electric power and wire-linetelecommunications systems and the interfering effects that may be produced are addressed. An interfacethat permits either party, without need to involve the other, to v

3、erify the induction at the interface by use ofa probe wire is presented. This recommended practice does not apply to railway signal circuits.Keywords: communication lines, electric supply, inductive coordinationThe Institute of Electrical and Electronics Engineers, Inc.345 East 47th Street, New York

4、, NY 10017-2394, USACopyright 1993 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 1993. Printed in the United States of AmericaISBN 1-55937-281-8No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, wi

5、thout theprior written permission of the publisher.IEEE Standardsdocuments are developed within the Technical Committees of theIEEE Societies and the Standards Coordinating Committees of the IEEE StandardsBoard. Members of the committees serve voluntarily and without compensation.They are not necess

6、arily members of the Institute. The standards developed withinIEEE represent a consensus of the broad expertise on the subject within the Instituteas well as those activities outside of IEEE that have expressed an interest in partici-pating in the development of the standard.Use of an IEEE Standard

7、is wholly voluntary. The existence of an IEEE Standarddoes not imply that there are no other ways to produce, test, measure, purchase, mar-ket, or provide other goods and services related to the scope of the IEEE Standard.Furthermore, the viewpoint expressed at the time a standard is approved and is

8、sued issubject to change brought about through developments in the state of the art and com-ments received from users of the standard. Every IEEE Standard is subjected toreview at least every ve years for revision or reafrmation. When a document ismore than ve years old and has not been reafrmed, it

9、 is reasonable to conclude thatits contents, although still of some value, do not wholly reect the present state of theart. Users are cautioned to check to determine that they have the latest edition of anyIEEE Standard.Comments for revision of IEEE Standards are welcome from any interested party,re

10、gardless of membership afliation with IEEE. Suggestions for changes in docu-ments should be in the form of a proposed change of text, together with appropriatesupporting comments.Interpretations: Occasionally questions may arise regarding the meaning of portionsof standards as they relate to specic

11、applications. When the need for interpretationsis brought to the attention of IEEE, the Institute will initiate action to prepare appro-priate responses. Since IEEE Standards represent a consensus of all concerned inter-ests, it is important to ensure that any interpretation has also received the co

12、ncurrenceof a balance of interests. For this reason IEEE and the members of its technical com-mittees are not able to provide an instant response to interpretation requests except inthose cases where the matter has previously received formal consideration. Comments on standards and requests for inte

13、rpretations should be addressed to:Secretary, IEEE Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAIEEE Standards documents are adopted by the Institute of Electrical and ElectronicsEngineers without regard to whether their adoption may involve patents on articles,materials, or

14、processes. Such adoption does not assume any liability to any patentowner, nor does it assume any obligation whatever to parties adopting the standardsdocuments.Authorized licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Auth

15、orized licensed use limited to: Southeast University. Downloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. iiiIntroduction(This introduction is not a part of IEEE Std 776-1992, IEEE Recommended Practice for Inductive Coordination of ElectricSupply and Communication Line

16、s.)During the ve years since IEEE Std 776-1987 was published, the guide has provided a useful tool for thosefaced with inductive coordination problems. Questions have arisen about the stringent harmonic distributionused on the probe-wire interface described in table 2. This version of IEEE Std 776 p

17、rovides exibility in theuse of harmonic distributions in table 2 to match the variety of existing environments and conditions. The gen-eral section was also rewritten in an effort to make it more understandable. Other sections have also beenimproved editorially. These efforts and contributions were

18、made by Dick Nelson, Harold Held, Bill McCoy,Charlie Nelson, Chrys Chrysanthou, and David Boneau.Since the publication of joint reports of the National Electric Light Association and the Bell System during andfollowing the 1920s, the joint responsibility of inductive coordination between power and t

19、elecommunicationcompanies has generally been accepted. However, the need has long been recognized for one document thatdenes the components of interference, provides specic procedures to predict levels of interference, providesspecic methods to demonstrate cause and effect relationships, and denes a

20、 threshold for initiating coordina-tion to mitigate interference. The Longitudinal Induction Working Group, which is under the direction of theInductive Coordination and Electrical Protection (ICEP) Subcommittee of the Transmission Systems Commit-tee of the Communications Society, has struggled to p

21、roduce a fair and equitable approach to ll this need underthe leadership of three different chairs. These chairs were, rst, Harold C. Held, retired from Illinois Bell Tele-phone Company; second, the late James R. Wilson, formerly afliated with South Central Bell Telephone Com-pany; and third, David

22、Lee Boneau of Southwestern Bell Telephone Company. Major contributions to thedocument were made by James R. Wilson, George Benz of Southern New England Telephone Company, andDavid Boneau. Members of the Oklahoma Power and Communications Association (originally the OklahomaInductive Coordination Asso

23、ciation) furthered the development of the document by eld testing and assuringthe validity of the various calculations and measurement techniques. Many others have reviewed and helped toformulate a guide that is usable by both power and telecommunication company personnel.ParticipantsLongitudinal In

24、duction Working Group members at the time of balloting are as follows:David Lee Boneau,ChairG. Y. R. Allen D. Huber H. E. NerhoodJ. Allison D. P. Hartmann S. D. OverbyM. J. Anna W. M. Haynes, Jr. P. PoolC. Chrysanthou H. C. Held K. SabineW. Dabisza R. G. Jones M. S. TibenskyJ. S. Gallatin J. F. Laid

25、ig W. B. WilkensR. F. Gundrum W. J. McCoy R. G. WunderC. D. Hansell C. R. Nelson L. S. YoungR. E. NelsonAuthorized licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast University. Dow

26、nloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. ivLongitudinal Induction Working Group members at the time of the 1987 version were as follows:David Lee Boneau,ChairG. Y. R. Allen D. P. Hartmann J. F. LaidigJ. E. Allison W. M. Haynes, Jr. W. J. McCoyM. J. Anna H. C. H

27、eld R. E. NelsonG. W. Benz L. M. Himmel, Sr. H. E. NerhoodW. Dabisza P. Jackson S. D. OverbyL. W. Grovenstein R. G. Jones R. W. ParkerR. Gundrum A. K. Knowles H. R. StevensonS. W. Guzik G. H. Kuhn J. ThorsonC. D. Hansell M. S. TibenskyThe following persons were on the balloting committee that approv

28、ed this document for submission to the IEEEStandards Board:G. Y. R. Allen D. Huber H. E. NerhoodJ. Allison D. P. Hartmann S. D. OverbyM. J. Anna W. M. Haynes, Jr. P. PoolC. Chrysanthou H. C. Held K. SabineW. Dabisza R. G. Jones M. S. TibenskyJ. S. Gallatin J. F. Laidig W. B. WilkensR. F. Gundrum W.

29、J. McCoy R. G. WunderC. D. Hansell C. R. Nelson L. S. YoungR. E. NelsonAuthorized licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast University. Downloaded on August 18,2018 at 13:3

30、7:55 UTC from IEEE Xplore. Restrictions apply. vWhen the IEEE Standards Board approved this standard on December 3, 1992, it had the following member-ship: Marco W. Migliaro,ChairDonald C. Loughry,Vice ChairAndrew G. Salem,SecretaryDennis Bodson Donald N. Heirman T. Don Michael*Paul L. Borrill Ben C

31、. Johnson John L. RankineClyde Camp Walter J. Karplus Wallace S. ReadDonald C. Fleckenstein Ivor N. Knight Ronald H. ReimerJay Forster* Joseph Koepnger* Gary S. RobinsonDavid F. Franklin Irving Kolodny Martin V. SchneiderRamiro Garcia D. N. Jim Logothetis Terrance R. WhittemoreThomas L. Hannan Lawre

32、nce V. McCall Donald W. Zipse*Member EmeritusAlso included are the following nonvoting IEEE Standards Board liaisons:Satish K. AggarwalJames BeallRichard B. EngelmanDavid E. SoffrinStanley WarshawRochelle L. SternIEEE Standards Project EditorAuthorized licensed use limited to: IEEE Standards Staff.

33、Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast University. Downloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. viContents1. Scope 12. References 13. General. 23.1 Inductive interference 23.2 Ne

34、ed for coordination 33.3 Mutual responsibility of parties involved 34. The inductive environment 34.1 Guidelines for an acceptable environment. 34.2 Methods of measurement. 124.3 Methods of prediction 225. Coordination within the inductive environment 295.1 General Coordination Methods 295.2 Specifi

35、c coordination methods. 306. Administrative methods and procedures 326.1 Intercompany meetings and contacts. 326.2 Mitigation of specific interference cases 327. Bibliography 34Annex A Example calculations 35A.1Prediction calculations. 35A.2Mitigation calculations. 49Annex B Decibel, power, and C-me

36、ssage noise . 52Authorized licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast University. Downloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. Authoriz

37、ed licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast University. Downloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. IEEE Recommended Practice forInd

38、uctive Coordination of Electric Supply and Communication Lines1. ScopeThis recommended practice addresses the inductive environment that exists in the vicinity of electric powerand wire-line telecommunications systems and the interfering effect that may be produced thereby; guidanceis offered for th

39、e control or modication of the environment and the susceptibility of the affected systems inorder to maintain an acceptable level of interference.To aid the user of this recommended practice in calculating induction between power and telecommunica-tion lines, the concept of an interface is developed

40、. This recommended practice permits either party, withoutneed to involve the other, to verify the induction at the interface by use of a probe wire. This recommendedpractice does not apply to railway signal circuits.2. ReferencesThis standard shall be used in conjunction with the following publicati

41、ons:IEEE Std 81-1983, IEEE Guide for Measuring Earth Resistivity, Ground Impedance, and Earth SurfacePotentials of a Ground System (ANSI).1IEEE Std 367-1987, IEEE Recommended Practice for Determining the Electric Power Station GroundPotential Rise and Induced Voltage from a Power Fault (ANSI).IEEE S

42、td 487-1992, IEEE Recommended Practice for the Protection of Wire-Line Communication FacilitiesServing Electric Power Stations (ANSI).IEEE Std 789-1988, IEEE Standard Performance Requirements for Communications and Control Cables forApplication in High Voltage Environments (ANSI).IEEE Std 820-1984 (

43、Reaff 1992), IEEE Standard Telephone Loop Performance Characteristics (ANSI).IEEE Std 1137-1991, IEEE Guide for the Implementation of Inductive Coordination Mitigation Techniques(ANSI).1IEEE publications are available from the Institute of Electrical and Electronics Engineers, Service Center, 445 Ho

44、es Lane, P.O. Box1331, Piscataway, NJ 08855-1331, USA.1IEEEStd 776-1992 IEEE RECOMMENDED PRACTICE FOR INDUCTIVEAuthorized licensed use limited to: IEEE Standards Staff. Downloaded on October 24, 2008 at 12:18 from IEEE Xplore. Restrictions apply.Authorized licensed use limited to: Southeast Universi

45、ty. Downloaded on August 18,2018 at 13:37:55 UTC from IEEE Xplore. Restrictions apply. 3. General3.1 Inductive interferenceInductive interference is dened as an effect, arising from the characteristics and inductive relations of elec-tric supply and telecommunication systems. It is of such character

46、 and magnitude that it would prevent thetelecommunication circuits from rendering service satisfactorily and economically if methods of inductivecoordination were not applied. Inductive interference is produced by the simultaneous coexistence of threefactors:a) An inductive inuenceb) A coupling mech

47、anism between two electrical systems or circuits, one of which produces theinuencec) A susceptibility of the second system or circuit to interferenceWhile inductive interference may occur at any time the above conditions are satised, the majority of casesand the principal concern of this recommended

48、 practice involve interference in telecommunication systemsas a result of their proximity to electric power systems. Therefore, subsequent discussion is limited to thatgeneral case, although the principles and practices may apply to other cases as well.3.1.1 Inductive inuence Inductive inuence is de

49、ned as those characteristics of an electric supply circuit that determine the charac-ter and intensity of the inductive eld that it produces. The voltage and current present on an operatingpower system produce electric and magnetic elds in the vicinity of the system. The character and intensityof those elds determine the inductive inuence. Character is related primarily to the frequencies present,while intensity is related to the magnitude of voltages and currents modied by line conguration, currentdistribution, and any shielding structures in the immedia