IEEE C37 20.7-2017 Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults《内部电弧故障用压力等级小于52kV的开关装置的测试用指南》.pdf

《IEEE C37 20.7-2017 Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults《内部电弧故障用压力等级小于52kV的开关装置的测试用指南》.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 20.7-2017 Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults《内部电弧故障用压力等级小于52kV的开关装置的测试用指南》.pdf（84页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults IEEE Std C37.20.7-2017 (Revision of IEEE Std C37.20.7-2007) IEEE Power and Energy Society Sponsored by the Switchgear Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std C37.20.7-2017 (Revision of IEEE Std C3

2、7.20.7-2007) IEEE Guide for Testing Switchgear Rated Up to 52 kV for Internal Arcing Faults Sponsor Switchgear Committee of the IEEE Power and Energy Society Approved 6 December 2017 IEEE-SA Standards BoardAbstract: Procedures for testing and evaluating the performance of switchgear for internal arc

3、ing faults is covered. A method of identifying the capabilities of this equipment is given. Service conditions, installation, and application of equipment are also discussed. As used in this document, the term switchgear is used as a general term covering switching and interrupting devices and their

4、 combination with associated control, instrumentation, metering, protective and regulating devices, assemblies of those devices with associated interconnections, accessories, and supporting structures used primarily in conjunction with the generation, transmission, distribution, and conversion of el

5、ectrical power. Keywords: accessibility, arc, arc-resistant, bus, compartment, IEEE C37.20.7, internal arcing fault, medium-voltage controllers, metal-clad switchgear, metal-enclosed bus, metal-enclosed gas-insulated switchgear, metal-enclosed interrupter switchgear, metal-enclosed low-voltage power

6、 circuit breaker switchgear, metal-enclosed switchgear, motor control centers, overpressure, protection, switchboard The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. A

7、ll rights reserved. Published 7 February 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any a

8、nd all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market,

9、 or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publ

10、ishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should

11、 rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDEN

12、TAL, SPECIAL, EXEMPLARY , OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY , WHETHER IN CONTRACT, STRICT LIABILITY , OR TORT (INCLUDING NEGLIGEN

13、CE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process i

14、nvolves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standa

15、rds Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting informati

16、on on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership a

17、ffiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a conse

18、nsus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or qu

19、estions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards sho

20、uld be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply

21、 compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and thes

22、e documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under US and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in l

23、aws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright

24、 2018 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of

25、 licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of

26、 IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time

27、 consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to review at least every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude th

28、at its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended t

29、hrough the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ ieeexplore .ieee .or g/ or contact IEEE at the address listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .

30、or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ findstds/ errata/ index .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementat

31、ion of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of a

32、ssurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ patcom/ patents .html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compen

33、sation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for iden

34、tifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agre

35、ements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Associatio

36、n.6 Copyright 2018 IEEE. All rights reserved. Participants At the time this IEEE guide was completed, the Arc-Resistant Switchgear Working Group had the following membership: Michael Wactor , Chair T. W . Olsen, Vice Chair Paul D. Barnhart Jerry Baskin Russell Boyce James E. Bowen Eldridge R. Byron

37、Jerry Earl Douglas J. Edwards Michael Flack Keith Flowers S. S. Gohil Thomas Hawkins Arthur Jur Chad Kennedy Mike LaFond David J. Lemmerman Frank Mayle Deepak Mazumdar Daleep Mohla Charles Allan Morse Darryl Moser Miklos J. Orosz Amit Patel Tim Rohrer Todd Sauve Carl Schneider James E. Smith Paul Su

38、llivan Chand Tailor Marcelo Valdes Robert Warren Terry Woodyard The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. Ali Ali Charles Ball Thomas Barnes Paul D. Barnhart Michael Bayer W. J. (Bill) Bergman J

39、ean-Marc Biasse William Bloethe James E. Bowen Rachel Bugaris David Burns Ted Burse William Byrd Eldridge R. Byron Paul Cardinal Robert Cohn Bryan Cole Glenn Davis Gary Donner Louis Doucet Edgar Dullni Donald Dunn Jerry Earl Douglas J. Edwards Donald Elliott Ronald Esco Michael Flack Keith Flowers M

40、arcel Fortin Fredric Friend Paul Gingrich Mietek Glinkowski S. S. Gohil Robert Goodin Lou Grahor Randall Groves Ajit Gwal John Harley Thomas Hawkins Jeffrey Helzer Werner Hoelzl Robert Hoerauf Dan Hrncir Richard Jackson Jose Jarque Wolfgang Jung Uwe Kaltenborn John Kaminski John Kay Chad Kennedy Yur

41、i Khersonsky James Kinney Boris Kogan Jim Kulchisky Chung-Yiu Lam Benjamin Lanz Hua Liu Frank Mayle William McBride John McClelland Daleep Mohla Charles Allan Morse Darryl Moser Dennis Neitzel Arthur Neubauer Michael Newman T. W . Olsen Lorraine Padden Mirko Palazzo Rahul Pawar Christopher Petrola I

42、ulian Profir Larry Putman Samala Santosh Reddy Timothy Robirds Tim Rohrer Thomas Rozek Ryandi Ryandi Todd Sauve Bartien Sayogo Nikunj Shah Devki Sharma Michael Sigmon Garett Sims James E. Smith Jeremy Smith Jerry Smith Tom Stefanski Paul Sullivan Chand Tailor David Tepen Dennis Thonsgard Wayne Timm

43、Nenad Uzelac Marcelo Valdes James Van De Ligt John Vergis Michael Wactor John Wang John Webb Kenneth White Terry Woodyard Dean Yager Robert Yanniello Larry Yonce7 Copyright 2018 IEEE. All rights reserved. When the IEEE-SA Standards Board approved this guide on 6 December 2017, it had the following m

44、embership: Jean-Philippe Faure, Chair Gary Hoffman, Vice Chair John Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Ted Burse Stephen Dukes Doug Edwards J. Travis Griffith Michael Janezic Thomas Koshy Joseph L. Koepfinger* Kevin Lu Daleep Mohla Damir Novosel Ronald C. Petersen Annette D. Reilly Robby Robson Dorothy Stanley Adrian Stephens Mehmet Ulema Phil Wennblom Howard Wolfman Yu Yuan *Member Emeritus