ASTM A888-2018a Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications.pdf

《ASTM A888-2018a Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications.pdf》由会员分享，可在线阅读，更多相关《ASTM A888-2018a Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications.pdf（59页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A888 18aStandard Specification forHubless Cast Iron Soil Pipe and Fittings for Sanitary andStorm Drain, Waste, and Vent Piping Applications1This standard is issued under the fixed designation A888; the number immediately following the designation indicates the year oforiginal adoption o

2、r, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers hubless cast iron soil pipe andfittings for use in g

3、ravity flow applications. It establishesstandards covering material, manufacture, mechanical andchemical properties, dimensions, coating, test methods,inspection, certification, and product marking for hubless castiron soil pipe and fittings. These pipe and fittings are intendedfor non-pressure appl

4、ications, as the selection of the propersize for sanitary drain, waste, vent, and storm drain systemsallows free air space for gravity drainage.1.2 The EDP/ASA numbers indicated in this section repre-sent a Uniform Industry Code adopted by theAmerican SupplyAssociation (ASA). A group designation pre

5、fix, 022, is as-signed to hubless products, followed by the four-digit identi-fication assigned to individual items and a check digit. Thissystem has been instituted to facilitate EDP control throughdistribution channels, and is to be used universally in orderingand specifying product items. Those i

6、tems with no EDPnumbers are either new, special, or transitory and will beassigned numbers on subsequent prints of this specification.1.3 This specification covers pipe and fittings of the follow-ing patterns and applies to any other patterns that conform withthe applicable requirements given in thi

7、s specification.21.3.1 Lengths:FiguresEDP/ASA Identification Numbersfor Hubless PipeFig. 110 ft (3.0 m) in sizes and 5 ft. (1.5 m)112,2,3,4,5,6,8,10, 12, and 15 in.Fig. 1, Fig. 2Method of Specifying Fittings Fig. 31.3.2 Fittings:Quarter Bend Fig. 5Quarter Bend, Reducing Fig. 6Quarter Bend, with Side

8、 Opening Fig. 7Quarter Bend, with Heel Opening Fig. 8Quarter Bend, Tapped Fig. 9Quarter Bend, Double Fig. 10Quarter Bend, Long Fig. 11Short Sweep Fig. 12Long Sweep Fig. 13Long Sweep, Reducing Fig. 14Fifth Bend Fig. 15Sixth Bend Fig. 16Eighth Bend Fig. 17Eighth Bend, Long Fig. 18Sixteenth Bend Fig. 1

9、9Sanitary Tee Fig. 20Sanitary Tee with Side Opening Fig. 21Sanitary Tee with 2 in. Side Opening R or L/R and L Fig. 22Sanitary Tee, New Orleans Special with Side Opening Fig. 23Sanitary Tee with 45 Side Openings and New Orleans Fig. 24Sanitary Special Tee Tapped Fig. 25Sanitary Tapped Tee, Horizonta

10、l Twin Fig. 26Sanitary Tapped Tee, Double Vertical Fig. 27Y Branch Fig. 28Y Branch, Double Fig. 29Y Branch, Upright Fig. 30Upright Y Wide Center Florida Special Fig. 31Y Branch, Combination18 Bend Fig. 32Y Branch, Combination18 Bend Double Fig. 33Sanitary Cross Fig. 34Sanitary Cross with Side Openin

11、g Fig. 35Sanitary Cross, New Orleans, with Side Openings Fig. 36Sanitary Cross, New Orleans, with 45 Special andRegular Side OpeningsFig. 37Sanitary Cross, Tapped Fig. 38Test Tee Fig. 39Tapped Extension Piece Fig. 40Increaser-Reducer Fig. 41Increaser-Reducer, Short Fig. 42Tapped Adapter Fig. 43Blind

12、 Plug Fig. 44Iron Body Cleanout, Tapped Fig. 45P Trap Fig. 46P Trap, Long Fig. 47P Trap, Deep Seal Fig. 48P Trap, with Primer Fig. 49P Trap, with Tapped Inlet Fig. 50Tapped Inlet, Double Fig. 51Modified Combination Wye and18 Bend, Double Fig. 52Modified Combination Wye and18 Bend, Double,ExtendedFig

13、. 53Two-Way Cleanout Fig. 54Twin Cleanout Fig. 55Closet Bend, Regular and Reducing Fig. 56Closet Flange Riser Fig. 571This specification is under the jurisdiction of ASTM Committee A04 on IronCastings and is under the direct responsibility of Subcommittee A04.12 on Pipesand Tubes.Current edition app

14、roved Nov. 15, 2018. Published December 2018. Originallyapproved in 1990. Last previous edition approved in 2018 as A888 18. DOI:10.1520/A0888-18A.2Reprinted with permission from Cast Iron Soil Pipe Institute (CISPI), 2401Fieldcrest Dr., Mundelein, IL 60060, http:/www.cispi.org.Available fromAmerica

15、nNational Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recogni

16、zed principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1Tapping Bosses Fig. 58Double Sweep Sanitary Tee (Extended) Fig. 59

17、Running Trap with Double Vents Fig. 60P Trap with Tapped or Hubless Side Inlet Fig. 61Vented Tub Wye Extended, Double Fig. 62Vented Tub Wye Extended Offset, Left or Right Fig. 63Vented Tub Wye Fig. 64Double Two-Way Cleanout Fig. 651.4 The values stated in inch-pound units are to be regardedas standa

18、rd. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The committee with jurisdiction over this standard isaware of another comparable standard published by the CastIron Soil Pipe Institute, CISPI 301.NOT

19、E 1The text of this standard references notes and footnotes thatprovide explanatory material. These notes and footnotes (excluding thosein tables and figures) shall not be considered as requirements of thestandard.1.6 This international standard was developed in accor-dance with internationally reco

20、gnized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3A48/A48M Specificati

21、on for Gray Iron CastingsA644 Terminology Relating to Iron CastingsD1248 Specification for Polyethylene Plastics ExtrusionMaterials for Wire and CableD3960 Practice for Determining Volatile Organic Compound(VOC) Content of Paints and Related CoatingsE8/E8M Test Methods for Tension Testing of Metalli

22、c Ma-terialsE1645 Practice for Preparation of Dried Paint Samples byHotplate or Microwave Digestion for Subsequent LeadAnalysisE2349 Practice for Safety Requirements in Metal CastingOperations: Sand Preparation, Molding, and Core Mak-ing; Melting and Pouring; and Cleaning and Finishing2.2 Federal St

23、andard:4Fed. Std. No. 123 Marking for Shipment (Civil Agencies)2.3 Military Standard:4MIL-STD-129 Military Marking for Shipment and Storage2.4 ANSI/ASME Standard:5B1.20 Pipe Threads2.5 Other Documents:Uniform Freight Classification Rules6National Motor Freight Classification Rules7Cast Iron Soil Pip

24、e Institute (CISPI) Specification 30183. Terminology3.1 Abbreviations:3.1.1 ACabove center3.1.2 ADAPTRadapter3.1.3 ifon the left, it shall be a left-hand fitting.8.2.1 Branch FittingsThe branch shall be placed towardthe observer and the outlet end of the run lower than thebranch.8.3 The fitting illu

25、strated in Fig. 3 has a right-hand inlet.Left-hand fittings have these openings on the side opposite tothat shown. Inlets on fittings shall be made with or withoutspigot bead and positioning lug.9. Coating9.1 The pipe and fittings shall be uniformly coated with amaterial suitable for the purpose tha

26、t is adherent and not brittle.The coating shall be applied in accordance with the coatingmanufacturers requirements. External touch marks frompoints of contact during the coating process are permitted. Thecoating shall not contain asbestos above current SDS report-able levels.9Safety data sheets sha

27、ll be furnished by thecoating manufacturer when requested. The coating shall beevenly and smoothly applied to all surfaces, except in threadedopenings, unless the coating is specifically designed forthreaded openings.9.2 Pipe and fittings coatings shall not contain lead whichexceeds levels above 0.0

28、6 % (600 ppm).9.2.1 The manufacturer shall annually prepare and submitsamples to a qualified laboratory for test in accordance withPractice E1645. The manufacturer shall prepare and submitsamples when changing sources of supply or the coatingmanufacturer changes formulations for the coating.9.3 Pipe

29、 and fittings coatings shall not contain levels ofvolatile organic hazardous air pollutants (VOHAPs) whichexceed levels of 2.6 lb (0.31 kg/L) of VOHAPs per gallon ofsolids in accordance with Practice D3960.9.3.1 The manufacturer shall annually certify that the coat-ing meets the VOHAP requirement. I

30、t is permissible for thecoating manufacturer to provide the certification.9.4 Records shall be maintained for a period of seven years.9.5 Copies of the coating certification shall be furnishedwhen requested.10. Sampling10.1 Chemical and mechanical tests shall be made regularlyand at sufficiently clo

31、se intervals for adequate determinationsof the significant chemical constituents and properties of thecast iron. A specimen taken from a finished product often doesnot produce the same results as a specimen formed by the9The Global Harmonized System of classification and labeling of chemicals setsth

32、e same rules for classifying hazards, and mandates the same format and content forlabels and Safety Data Sheets for use around the world.TABLE 1 EDP Identification Numbers for Hubless PipeNOTE 1When ordering by these EDP numbers, be sure to include thecheck () digit following the item number (022 01

33、26 7). This check digitis verification of the group and item number you select.ManufacturersItemCodeDescriptionAGroup Item No. =10 ft (3 m) lengthHubless pipe (see Fig. 1) 0156 4 1120158 0 2120160 6 3022 0162 2 40164 8 50168 9 60170 5 80171 3 100172 7 120173 1 15AEDP numbers for fittings will appear

34、 in each of the respective tables.A888 18a4method used for sample preparation and is not acceptable forthe purposes of testing to this standard. Records of chemicalanalysis shall be maintained by the manufacturer. Copies ofthese analyses shall be furnished to the purchaser whenrequested.10.2 A lot s

35、hall consist of one of the following:10.2.1 All the metal poured from a single heating in abatch-type furnace.10.2.2 All the metal from two or more batch-type meltingfurnaces poured into a single ladle or a single casting.10.2.3 All the metal poured from a continuous meltingfurnace for a given perio

36、d of time between changes in charge,processing conditions, or aim-for chemistry or 4 h, whicheveris the shorter period.11. Test Methods11.1 Gray Iron:11.1.1 Tensile Strength TestTest bars shall be cast inaccordance with the requirements of Specification A48/A48M.The machined test bar dimensions and

37、drawing and dimensionsof as-cast test bars are found in Fig. 4. The tensile strength shallbe determined in accordance with Test Methods E8/E8M.11.1.2 Tension test reports shall include breaking load oftest bars, machined diameter of test bar, and calculated tensilestrength.12. Inspection12.1 Inspect

38、ion and Test by the ManufacturerPipe andfittings shall be inspected to verify compliance with thisspecification. The manufacturer shall maintain a record of allinspections.12.2 Pipe InspectionAt regular intervals (not to exceed12 h) during the course of production, sample pieces of eachsize of pipe

39、or pipes being produced shall be selected randomlyfor inspection. Each pipe selected shall be measured bysuitable gages and all dimensions detailed in Fig. 1 verified tocomply with the requirements of this specification. The inspec-tion records shall be maintained by the manufacturer for aperiod of

40、seven years.12.3 Fitting InspectionAt regular intervals (not to exceedtwelve hours) during the course of production, sample piecesof each size and configuration of fitting being produced shall beselected randomly for inspection. Each fitting selected shall bemeasured by suitable gages to verify that

41、 the laying length (asdetailed in Figs. 465), and all applicable dimensions detailedin Figs. 1 and 2 comply with the requirements of thisspecification. The inspection records shall be maintained by themanufacturer for a period of seven years.12.4 Marking InspectionInspection shall include verifica-t

42、ion that the markings on pipe and fittings comply with Section14.13. Certification13.1 Upon request the purchaser, design professional, or theadministrative authority having jurisdiction where the productsare being installed shall be furnished certification by themanufacturer stating samples represe

43、nting each lot have beentested and inspected as indicated in this specification and therequirements have been met. If required by the purchaser,design professional, or the administrative authority havingjurisdiction where the products are being installed, certificationshall be accompanied by test re

44、ports as prepared in accordancewith Sections 11 and 12. Tension test reports shall includebreaking load machined diameters of test bars and calculatedtensile strength. Certification shall include legal name andaddress of the manufacturer.13.2 Third-party certifiers or inspectors shall utilize thepro

45、cedures detailed in Annex A1 when conducting inspectionsat the manufacturing locations.14. Product Marking14.1 Each length of pipe and each fitting shall be plainlymarked with the country of origin and the manufacturers nameor manufacturers registered trademark by which the manufac-turer can be read

46、ily identified after installation. The markingshall be adequate identification of the manufacturer of the pipeand fittings if it readily identifies the manufacturer to the enduser of the product. Other markings on pipes and fittings shallbe permitted, provided such markings are not misleading withre

47、spect to the identification of the manufacturer by the enduser.14.1.1 Pipe MarkingsThe pipe shall be marked continu-ously on the barrel with a minimum of 0.75-in. (19-mm)lettering starting within 3 in. of each end of the pipe. Each pipeshall be marked with the date of manufacture. The markingshall b

48、e stenciled on the pipe or otherwise applied so as to beclear and legible.14.1.2 On fittings, the marking shall be cast with raisedletters that are not to be located within the W dimension, asshown in Fig. 2. Cast markings shall be raised from the wall ofthe fitting unless otherwise noted.15. Packag

49、ing and Package Marking15.1 Government ProcurementUnless otherwise specifiedin the contract, the material shall be packaged in accordancewith the suppliers standard practice, which will be acceptableto the carrier at lowest rates. Containers and packing shallcomply with Uniform Freight Classification Rules or NationalMotor Freight Classification Rules. Marking for shipment ofsuch material shall be in accordance with Fed. Std. No. 123 forcivil agencies and MIL-STD-129 for military agencies.16. Keywords16.1 cast iron; hubless pipe and fittings; no-hub pipe