UL 62275 CRD-2014 UL Standard for Safety for Cable Management Systems - Cable Ties For Electrical Installations - Section Paragraph Reference 3 7 8 9 10 11 Subject Inclusion of Ty.pdf

《UL 62275 CRD-2014 UL Standard for Safety for Cable Management Systems - Cable Ties For Electrical Installations - Section Paragraph Reference 3 7 8 9 10 11 Subject Inclusion of Ty.pdf》由会员分享，可在线阅读，更多相关《UL 62275 CRD-2014 UL Standard for Safety for Cable Management Systems - Cable Ties For Electrical Installations - Section Paragraph Reference 3 7 8 9 10 11 Subject Inclusion of Ty.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the a

2、pplicable UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): ZODZ, ZODZ2Standard Number: UL 62275Standard Title: Standard for Cable Management Systems Cable Ties for ElectricalInstallationsEdition Date: February 26, 20

3、10Edition Number: 1Section / Paragraph Reference: New 6.2.3DV, Revised 7.1DV.2, 9.1DV.1, 9.1DV.4,9.7.1DV.1 9.7.1DV.3, 9.7.1DV.6, 9.7.2DV.1, 9.7.3DV.1, Figure 5DVSubject: Integrally molded fixing device clarificationDECISION:Add new clause 6.2.3DV D1 as follows:6.2.3 DV D1 Add the following:6.2.3DV.1

4、 A cable tie and fixing device that are manufactured as an integral product shallhave a single Type classification according to either 6.2.1, 6.2.1DV.1 , 6.2.2 or 6.2.2 DV.1.Revise clause 7.1DV.2 as follows:7.1DV.2 The following markings shall be provided on labels, packaging, or installationinstruc

5、tions shipped with the product:. A cable tie and fixing device that aremanufactured as an integral product shall have a single Type designation per 6.2.3DV.1and shall be marked with both the mechanical strength declared for the fixing device andthe loop tensile strength declared for the cable tie. T

6、he declared mechanical strength ofthe fixing device that is integral to a cable tie shall not exceed the declared value for theloop tensile strength of the cable tie.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFixing devices Cable ties Cab

7、le ties with fixing devices as anintegral productMax operating temp for applicationaccording to Table 3Max operating temp for applicationaccording to Table 3Max operating temp for applicationaccording to Table 3Min operating temp for applicationaccording to Table 4aMin operating temp for application

8、according to Table 4Min operating temp for applicationaccording to Table 4Min installation temp if lower than 0C Min installation temp if lower than 0CType designation Type designation Type designationb Minimum and maximum bundle diameter Minimum and maximum bundle diameterMechanical strength as dec

9、lared by themanufacturerLoop tensile strength of the cable tieaccording to Table 2Mechanical strength of the fixing deviceand loop tensile strength of the cable tie,as declared by the manufacturer. If thetwo ratings are the same, a singlecombined rating may be declared. If thetwo ratings differ, bot

10、h shall be declared.aSeparately supplied Type 11 fixing devices need not be marked with the minimum operating temperature. This marking isoptional for such productsbFixing devices that are integral to a cable tie are classified according to the Type for the cable tie.Revise clause 9.1DV.1 as follows

11、:9.1DV.1 The cable tie and/or its associated fixing device shall withstand the stresseslikely to occur during installation and application. A fixing device that is integral to acable tie shall be tested using complete samples. See Clause 5.8. The cable tie shall:a) be capable of fixing the maximum a

12、nd minimum bundle diameter declared bythe manufacturer.Compliance shall be checked by the test specified in 9.2.b) be able to be installed at the minimum temperature declared by themanufacturer.Compliance shall be checked by the test specified in 9.3, for cable ties classifiedaccording to 6.1.2 and

13、6.1.3 only.NOTE This requirement does not apply to cable ties intended to be installed at temperaturesof 0 C or higher.c) be resistant to the effect of impact forces at the minimum operatingtemperature declared by the manufacturer.Compliance shall be checked by the test specified in 9.4, for cable t

14、ies classifiedaccording to 6.1.2 and 6.1.3 only.d) maintain its fixing function at the minimum and maximum applicationtemperature declared by the manufacturer. In Canada and the United States,metallic cable ties shall maintain their fixing function when exposed to vibration.NOTE Non-metallic and com

15、posite cable ties are considered to be resistant to the effects ofvibration.STANDARD NUMBER: UL 62275 -2-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULCompliance shall be checked by the relevant tests. Cable ties classifiedaccording to 6.2.1

16、 (Type 1) shall be checked by the tests specified in 9.5. Cableties classified according to 6.2.2 (Type 2) shall be checked by the tests specifiedin 9.6.In Mexico, the vibration test specified in 9.6.4 does not apply.Revise clause 9.1DV.4 as follows:9.1DV.4 The fixing device shall maintain its fixin

17、g function at the minimum and maximumapplication temperature as declared by the manufacturer. See Clause 9.1DV.1.NOTE Separately supplied fixing devices are classified only as Type 2 according to 6.2.2 or, in Canadaand the United States, Type 21 according to 6.2.2DV.1.Compliance shall be determined

18、by the tests specified in 9.7.Replace clause 9.7DV.1 as follows:9.7.1DV.1 A fixing device that is not provided with the means necessary to complete itsassembly in or to a mounting surface shall be fixed firmly to a rigid support according tothe manufacturers instructions. For a separately supplied f

19、ixing device, an appropriatecable tie shall be assembled to the fixing device and then to a non-split mandrelaccording to 5.9. For a fixing device that is integral to a cable tie, the integral tie shall beinstalled on a non-split mandrel according to 5.9. Typical arrangements of the testassembly for

20、 such fixing devices are shown in Figures 5DVA and 5DVC. The mountinghardware used to attach the fixing device to the mounting surface shall not be tested.Revise clause 9.7DV.2 as follows:9.7.1DV.2 A fixing device that is provided with the means necessary to complete itsassembly in or to a mounting

21、surface shall be assembled as intended to an appropriatesurface. For a separately supplied fixing device, an appropriate cable tie shall beassembled to the fixing device and then to a non-split mandrel according to 5.9. For afixing device that is integral to a cable tie, the integral tie shall be in

22、stalled on a non-splitmandrel according to 5.9. Typical arrangements of the test assembly for such fixingdevices are shown in Figure 5DVB.Revise clause 9.7.1DV.3 as follows:9.7.1DV.3 For Type 2 and Type 21 devices, the samples shall be subjected to a tensilepull until the mechanical strength declare

23、d by the manufacturer is reached. This loadshall be maintained for 60+50seconds. The test fixture shall allow for self-alignment ofthe test load with respect to the cable tie and the fixing device during the test.Note: It is important to be sure the test load is aligned, or permitted to naturally al

24、ign during the pullfor fixing devices that are integrally molded with a cable tie. Use of universal joints on the jaws of thetesting machine and/or a sliding mounting table can facilitate this.Revise clause 9.7.1DV.6 as follows:STANDARD NUMBER: UL 62275 -3-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR

25、FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL9.7.1DV.6 For Type 11 devices, each sample shall be subjected to a tensile pull. Noindividual value shall be less than the declared mechanical strength of the fixing device.The test fixture shall allow for self-alignment of the test load

26、with respect to the cable tieand the fixing device during the test.Note: It is important to be sure the test load is aligned, or permitted to naturally align during the pullfor fixing devices that are integrally molded with a cable tie. Use of universal joints on the jaws of thetensile machine and/o

27、r a sliding mounting table can facilitate this.Replace Figure 5DV as follows:This is generated text for figtxt.STANDARD NUMBER: UL 62275 -4-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFigure 5DVATypical arrangement of test assembly for a s

28、eparately supplied fixing deviceKey1 Cable tie 5 Support2 Locking device A Diameter of test mandrel3 Mandrel B Width of test mandrel4 Fixing DeviceSTANDARD NUMBER: UL 62275 -5-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFigure 5DVBTypical

29、arrangement of test assembly for an integral push-mount fixing deviceKey1 Cable tie 5 Support2 Locking device A Diameter of test mandrel3 Mandrel B Width of test mandrel4 Fixing DeviceSTANDARD NUMBER: UL 62275 -6-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT

30、PERMISSION FROM ULFigure 5DVCTypical arrangement of test assembly for an integral screw-mount fixing deviceKey1 Cable tie 5 Support2 Locking device A Diameter of test mandrel3 Mandrel B Width of test mandrel4 Fixing DeviceSTANDARD NUMBER: UL 62275 -7-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHE

31、R REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULRevise clause 9.7.2DV.1 as follows:9.7.2DV.1 The test shall be conducted on a new set of samples. Samples shall beassembled and mounted to the test fixture as described in 9.7.1. Moisture stabilizationaccording to 5.2 prior to heat aging is not

32、 applicable for this test. When it is determinedimpractical to age the samples according to 9.7.2DV.2 when mounted to the test fixture,the samples shall be conditioned separately and then mounted to the test fixture prior tothe tensile pull in clause 9.7.2DV.3. When the samples are aged separately,

33、if it isdetermined that the test results have been influenced by handling of the samples duringassembly to the test fixture following aging, a separate set of samples shall be aged afterconsideration of a method that mitigates a reoccurrence. The cable tie of a sample thathas an integral fixing devi

34、ce shall be assembled to an appropriate mandrel according toclause 9.6.2 prior to aging.Revise clause 9.7.3DV.1 as follows:9.7.3DV.1 The test shall be conducted on a new set of samples. Samples shall beassembled and mounted to the test fixture as described in 9.7.1. Moisture stabilizationaccording t

35、o 5.2 prior to heat aging is not applicable for this test. When it is determinedimpractical to submit the samples to the temperature cycling according to 9.7.2DV.2when mounted to the test fixture, the samples shall be cycled separately and thenmounted to the test fixture prior to the tensile pull in

36、 clause 9.7.3DV.3. When the samplesare cycled separately, if it is determined that the test results have been influenced byhandling of the samples during assembly to the test fixture following cycling, a separateset of samples shall be cycled after consideration of a method that mitigates areoccurre

37、nce. The cable tie of a sample that has an integrally molded fixing device shallbe assembled to an appropriate mandrel according to clause 9.6.2 prior to cycling.RATIONALE FOR DECISION:It has come to ULs attention that the practical application of tests for cable ties that have integrally moldedfixi

38、ng devices require clarification. Clause 5.8 states: “A fixing device that is integral to a cable tie shallcomply with the requirements for both the fixing device and the cable tie.” In normal use, the integrallymolded product acts as a system. It is therefore important to recognize that the actual

39、strength of the cableties locking mechanism may be less than the loop tensile strength of the cable tie determined by tests inclauses 9.5 or 9.6 due to the reaction to forces applied during testing of the fixing device according toClause 9.7. Conversely, it is also possible that the actual mechanica

40、l strength of the fixing device, whentested in accordance with clause 9.7, may also be less due to the systems reaction to the test force.The requirements above are deemed necessary to ensure consistency and repeatability of the tests andto provide the user with important information for safe use of

41、 the products.Copyright 2013 Underwriters Laboratories Inc.UL, in performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requiremen

42、t Decisions are the opinion of Underwriters Laboratories Inc. inpractically applying the requirements of the standard. They do not represent formal interpretations of thestandard under American National Standards Institute (ANSI) processes. UL shall not be responsible toanyone for the use of or reli

43、ance upon Certification Requirement Decisions by anyone. UL shall not incurany obligation or liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The electronic version of theCertification Requiremen

44、t Decision is the current version and previously printed copies may be outdated.STANDARD NUMBER: UL 62275 -8-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThis document is published as a service to ULs certification customersSTANDARD NUMBER: UL 62275 -9-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULSTANDARD NUMBER: UL 62275 -10-No Text on This Page