SANS 21003-5-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 5 Fitness for purpose of the system《建筑物内部热水和冷水装置用多层管道系统 第5部分 系统的适用性》.pdf

《SANS 21003-5-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 5 Fitness for purpose of the system《建筑物内部热水和冷水装置用多层管道系统 第5部分 系统的适用性》.pdf》由会员分享，可在线阅读，更多相关《SANS 21003-5-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 5 Fitness for purpose of the system《建筑物内部热水和冷水装置用多层管道系统 第5部分 系统的适用性》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21119-6 SANS 21003-5:2008 Edition 1 ISO 21003-5:2007 Edition 1SOUTH AFRICAN NATIONAL STANDARD Multilayer piping systems for hot and cold w

4、ater installations inside buildings Part 5: Fitness for purpose of the system This national standard is the identical implementation of ISO 21003-5:2007 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road gro

5、enkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 21003-5:2008 Edition 1 ISO 21003-5:2007 Edition 1

6、 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanSA SC 5120.12K, Water and sanitation Equipment and systems Plastics pipes and fittings, in accordance with procedures of Standards South Africa, in compliance with annex 3 of

7、the WTO/TBT agreement. This SANS document was published in May 2008. This adopted Final Draft International Standard (FDIS) has the status of a South African National Standard. The FDIS will be replaced by the final ISO document at the time of its publication. This standard may only be used and prin

8、ted by approved subscription and freemailing clients of the SABS. ISO 2007 All rights reserved N135 Document type: International Standard Document subtype: Document stage: (50) Approval Document language: E C:DOCUME1petermLOCALS1TempISO FDIS 21003-5.doc STD Version 2.1 ISO TC 138/SC 2 Date: 2007-07-

9、01 . ISO/FDIS 21003-5:2007(E) ISO TC 138/SC 2/WG 5 Secretariat: SNV Multilayer piping systems for hot and cold water installations inside buildings Part 5: Fitness for purpose Systmes de canalisations en multicouches pour installations deau chaude et froide lintrieur des btiments Partie 5: Covenable

10、 pour le intention de system SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-5:2007(E) ii Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitte

11、d under the applicable laws of the users country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for

12、permission to reproduce should be addressed to either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject

13、to royalty payments or a licensing agreement. Violators may be prosecuted. SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-5:2007(E) iii Contents Foreword.iv Introduction.v 1 Scope1 2 Normative references1 3 Term

14、s and definitions .2 4 Symbols and abbreviated terms 2 5 Fitness for purpose of the joints and the piping system 3 5.1 General3 5.2 Internal pressure test 3 5.3 Bending test .5 5.4 Pull-out test 6 5.5 Thermal cycling test7 5.6 Pressure cycling test.8 5.7 Leak tightness under vacuum8 Annex A (normati

15、ve) List of reference product standards.9 Bibliography10 SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-5:2007(E) iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of

16、 national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Int

17、ernational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with t

18、he rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval

19、by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21003-5 was prepared by Technical Committee

20、 ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies. ISO 21003 consists of the following parts, under the general title Multilayer piping systems for hot and cold water installations inside buildings: Part 1:

21、 General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-5:2007(E) v Introduction The sys

22、tem Standard, of which this is Part 5, specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potential adverse effects on the quality of water intended for human consumption,

23、 caused by the product covered by ISO 21003: This Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulati

24、ons concerning the use and/or the characteristics of this product stay in force. Requirements and test methods for components of the piping systems are specified in ISO 21003-1, ISO 21003-2 and ISO 21003-3 of the ISO 21003-series. CEN ISO/TS 21003-7 gives guidance for the assessment of conformity. T

25、his part of ISO 21003 specifies the characteristics for fitness for purpose. NOTE ISO 21003 does not incorporate a Part 4 Ancillary equipment or a Part 6 Guidance for installation. For ancillary equipment separate standards can apply. A guidance for installation for multilayer piping systems made fr

26、om different materials, intended to be used for hot and cold water installations, is covered by ENV 12108:2001. SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 21003-5:2008This standard may only be used and printed by appr

27、oved subscription and freemailing clients of the SABS.FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 21003-5:2007(E) ISO 2007 All rights reserved 1Multilayer piping systems for hot and cold water installations inside buildings Part 5: Fitness for purpose 1 Scope This part of ISO 21003 specifies the cha

28、racteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperature

29、s according to the class of application (see Table 1 of ISO 10508). It also specifies the test parameters for the test methods referred to in this standard. Part 5 of the ISO 21003-series is one part of a reference product standard. This series is applicable to multilayer pipes, fittings, their join

30、ts and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations in conjunction with all other parts of ISO 21003. This standard covers a range of service conditions (application classes) and design pressures. For values of T D ,

31、T maxand T malin excess of those in Table 1, this standard does not apply NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practi

32、ces or codes. The polymeric materials used for the stress designed layers are the following: polybutylene (PB), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C). NOTE For the purpose of this Intern

33、ational Standard crosslinked polyethylene (PE-X) as well as adhesives are to be considered as thermoplastic materials. PE-X shall be crosslinked and shall comply with the requirements of the reference product standard. 2 Normative references The following referenced documents are indispensable for t

34、he application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the

35、 resistance to internal pressure Part 1:General method ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2:Preperation of pipe test pieces ISO 10508, Thermoplastics pipes and fittings for hot and cold wate

36、r installations Guidance for classification and design ISO 13760, Plastics pipes for the conveyance of fluids under pressure Miners rule Calculation method for cumulative damage SANS 21003-5:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.I

37、SO/FDIS 21003-5:2007(E) 2 ISO 2007 All rights reservedISO 15874-5, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 5: Fitness for purpose of the system ISO 15875-5, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part

38、5: Fitness for purpose of the system ISO 15876-5, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 2: Fitness for purpose of the system ISO 15877-5, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC- C) Part 5: Fitne

39、ss for purpose of the system ISO 17456, Plastics piping systems Multi-layer pipes Determination of the long term hydrostatic strength ISO/DIS 21003-1:, Multilayer piping systems for hot and cold water installations inside buildings Part 1: General ISO/DIS 21003-2:, Multilayer piping systems for hot

40、and cold water installations inside buildings Part 2: Pipes ISO/DIS 21003-3:, Multilayer piping systems for hot and cold water installations inside buildings Part 3: Fittings ISO/FDIS 22391-5, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance

41、(PE-RT) Part 5: Fitness for purpose EN 712, Thermoplastics plastics piping systems End-load bearing mechanical joints between pressure pipes and fittings Test method for resistance to pull-out under constant longitudinal force EN 713, Plastics piping systems Mechanical joints between fittings and po

42、lyolefin pressure pipes Test method for leak tightness under internal pressure of assemblies subjected to bending EN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling EN 12294, Plastics

43、piping systems for hot and cold water Method of test for leaktightness under vacuum EN 12295, Plastics piping systems Thermoplastics pipes and associated fittings for hot and cold water Test methods for resistance of joints to pressure cycling 3 Terms and definitions For the purposes of this standar

44、d, the terms and definitions given in ISO 21003-1 apply. 4 Symbols and abbreviated terms For the purposes of this International Standard, the symbols and abbreviated terms given in ISO 21003-1 and ISO 21003-3 apply. SANS 21003-5:2008This standard may only be used and printed by approved subscription

45、 and freemailing clients of the SABS.ISO/FDIS 21003-5:2007(E) ISO 2007 All rights reserved 35 Fitness for purpose of the joints and the piping system 5.1 General When tested in accordance with the applicable methods as specified in Table 1, using the indicated parameters given in 5.2 to 5.7, the joi

46、nts and the piping system shall have characteristics conforming to the requirements given in the applicable clauses. For the tests described the fittings shall be connected to the pipe with which they are intended to be used. Table 1 specifies the tests applicable for each different type of jointing

47、 system covered by this standard. Table 1 Joint tests Jointing systemaTest Solvent cemented Fusion Socket Electro fusion Mechanical Test parameters Test method Internal pressure testY Y Y Shall conform to 5.2 ISO 1167-series Bending test Y Y Y Shall conform to 5.3 EN 713 Pull-out test Y Y Y Shall co

48、nform to 5.4 EN 712 Thermal cycling test Y Y Y Shall conform to 5.5 EN 12293 Pressure cycling test Y Y Y Shall conform to 5.6 EN 12295 Vacuum test Y Y Y Shall conform to 5.7 EN 12294 aY - denotes test applicable N - denotes test not applicable 5.2 Internal pressure test When tested in accordance wit

49、h ISO 1167-series using the test parameters given in Table 2 for the relevant classes the joint assembly shall not leak. The test pressure shall be calculated using the following equation: CD C D F p p p p = (1) where p F is the hydrostatic test pressure, in bar, to be applied to the assembly during the test period p Cis the value of the pressure, in bar, of the pipe construction corresponding to time to failure/test temperature in accordance with ISO 21003-2. p CDi