SANS 1116-3-2008 Retro-reflective number plates for motor vehicles Part 3 Blank plates (plastics)《机动车辆用回复反射号码牌 第3部分 空白牌(塑料)》.pdf

《SANS 1116-3-2008 Retro-reflective number plates for motor vehicles Part 3 Blank plates (plastics)《机动车辆用回复反射号码牌 第3部分 空白牌(塑料)》.pdf》由会员分享，可在线阅读，更多相关《SANS 1116-3-2008 Retro-reflective number plates for motor vehicles Part 3 Blank plates (plastics)《机动车辆用回复反射号码牌 第3部分 空白牌(塑料)》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22226-0 SANS 1116-3:2008Edition 3SOUTH AFRICAN NATIONAL STANDARD Retro-reflective number plates for motor vehicles Part 3: Blank plates (p

4、lastics) Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 1116-3:2008 Edition 3 Table of changes Change No. Date Scope Foreword This South African standard was approved by National Commi

5、ttee SABS TC 1070, Retro-reflection, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in December 2008. This document supersedes SABS 1116-3:1996 (edition 2.1). Reference is made in clauses 1 and 3 to the “

6、relevant national legislation“. In South Africa this means the National Road Traffic Act, 1996 (Act No. 93 of 1996) (as amended from time to time). SANS 1116 consists of the following parts, under the general title Retro-reflective number plates for motor vehicles: Part 1: Blank plates (aluminium).

7、Part 2: Number plates (aluminium). Part 3: Blank plates (plastics). Part 4: Number plates (plastics). Annexes A, B and C are for information only. SANS 1116-3:2008 Edition 3 1 Contents Page Foreword 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Requirements 4 5 Inspection and methods of test

8、. 5 5.1 Inspection. 5 5.2 Test specimens 5 5.3 Resistance to weathering. 5 5.4 Resistance to impact 5 5.5 Colour (white, black, blue, brown, green or red) and luminance factor test 6 6 Packing 6 7 Marking 6 Annex A (informative) Quality verification of plastics blank plates for retro-reflective numb

9、er plates 10 Annex B (informative) Location of holes on number plates . 11 Annex C (informative) Security decal. 14 Bibliography. 14 SANS 1116-3:2008 Edition 3 2 This page is intentionally left blank SANS 1116-3:2008 Edition 3 3 Retro-reflective number plates for motor vehicles Part 3: Blank plates

10、(plastics) 1 Scope This part of SANS 1116, in addition to the relevant national legislation (see foreword), specifies requirements for plastics blank plates that are intended for use in the production of number plates covered in SANS 1116-4. NOTE Annexes A and B provide information on the quality ve

11、rification of plastics blank plates for retro-reflective number plates, and the location of holes on number plates, respectively. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. Fo

12、r undated references, the latest edition of the referenced document (including any amendments) applies. Information on currently valid national and international standards can be obtained from the SABS Standards Division. ASTM D 1003, Standard test method for haze and luminous transmittance of trans

13、parent plastics. ASTM G 154, Standard practice for operating fluorescent light apparatus for UV exposure of non-metallic materials. CIE 15, Colorimetry. SANS 1116-1, Retro-reflective number plates for motor vehicles Part 1: Blank plates (aluminium). SANS 2813/ISO 2813, Paints and varnishes Determina

14、tion of specular gloss of non-metallic paint films at 20, 60 and 85. 3 Definitions For the purposes of this document, the definitions given in the relevant national legislation (see foreword), SANS 1116-1 and the following apply. blank plate blank flat plastics transparent plate of a specified size,

15、 and that is used in the manufacture of number plates SANS 1116-3:2008 Edition 3 4 4 Requirements 4.1 Blank plates A blank plate shall be manufactured from a transparent UV stable plastics material that, when measured in accordance with SANS 2813, shall have a surface specular gloss of at least 80 a

16、t 60, and an optical quality of not less than 90 % when tested in accordance with ASTM D 1003. The thickness of the blank plate shall be between 3 mm and 4 mm. The blank plate shall be manufactured by an injection moulding process and shall bear the manufacturers name or trademark in the top right c

17、orner, and shall be contained within a maximum space of 12 mm high and 50 mm in length, which shall be part of the moulding process. 4.2 Shape and dimensions When measured in accordance with 5.1, blank plates shall be rectangular, with corners rounded to a radius of 15 mm 3 mm, shall be free from sh

18、arp edges and burrs, and shall be of one of the following sizes: a) 440 mm ( 1 mm) 120 mm ( 1 mm) (for vehicles registered before 1 January 2010); b) 250 mm ( 1 mm) 205 mm ( 1 mm); c) 520 mm ( 1 mm) 113 mm ( 1 mm); or d) 250 mm ( 1 mm) 165 mm ( 1 mm). 4.3 Border and workmanship 4.3.1 Border The bord

19、er of a blank plate shall be as shown in figure 1 and shall extend around the four sides of the plate. The border shall be black, blue, red, green or brown. 4.3.2 Workmanship A blank plate shall be of such flatness that, when it is laid (with the face upwards) on a flat supporting surface, no part o

20、f the lower surface of the plate is more than 3 mm from the supporting surface. 4.4 Performance 4.4.1 Resistance to weathering When tested in accordance with 5.3, the blank plate shall show no signs of cracking, change in optical quality, change in surface specular gloss, or change of dimensions whe

21、n inspected and measured in accordance with 5.1 and ASTM D 1003. 4.4.2 Resistance to impact When tested in accordance with 5.4, the border and the base material shall show no cracking outside a distance of 20 mm from the impacted area. SANS 1116-3:2008 Edition 3 5 4.4.3 Colour and luminance factor o

22、f the border 4.4.3.1 Colour The border shall be black, blue, red, green, or brown. 4.4.3.2 Luminance factor When the luminance factor of the colours black, blue, red, green or brown is determined in accordance with 5.5, it shall not exceed 0,07. 5 Inspection and methods of test 5.1 Inspection Visual

23、ly examine and then measure each blank plate in the sample for compliance with all the relevant requirements for which tests to assess compliance are not given in 5.3 to 5.5 (inclusive). 5.2 Test specimens From the sample blank plates that include the expiry decal, if applicable, prepare one complet

24、e blank number plate for each of the tests as given in 5.3 to 5.5. 5.3 Resistance to weathering 5.3.1 Mount the test specimen (see 5.2) with the test surface facing the lamps, and subject it to artificial weathering using the apparatus and method given in ASTM G 154 for 240 h using a cycle of 4 h UV

25、 exposure at 60 C and then 4 h condensation exposure at 50 C. 5.3.2 Check for compliance with 4.4.1. 5.4 Resistance to impact 5.4.1 Apparatus 5.4.1.1 Apparatus, as shown in figures 2 and 3. 5.4.1.2 Number plate holding fixture that consists of a piece of steel channel 400 mm 250 mm 75 mm on which tw

26、o sample supports 75 mm 10 mm are located in a vertical position, resting on the long cross-section edge, across the width of the flat face of the steel channel. The spacing of the support plates is equidistant from the centre of the steel channel. The distance between the inside faces of the suppor

27、t plates is 250 mm (see figures 2 and 3). The test sample is clamped to each support by means of a 9 mm square bar. The bar is the same length as the support plate and is retained in alignment by a pair of vertical steel bars attached to each end of the support plate. A 20 mm steel bar is attached t

28、o the top of the alignment plates, in a horizontal position, to form a bridge over the support plate and clamping bar. The M8 set screws located in the threaded holes positioned in the centre of the span of each bridge bar, are used to apply pressure to the clamp bars. 5.4.1.3 Striker that is constr

29、ucted from steel rod and that has a spherical striking nose of 6,5 mm radius. It is used with a drop tube of any suitable material that is straight, that has an inside diameter slightly larger than the falling mass, and that does not restrict its free fall. SANS 1116-3:2008 Edition 3 6 5.4.2 Procedu

30、re 5.4.2.1 Clamp the test specimen flat with the front face uppermost and with an overhang at each end. 5.4.2.2 Tighten the set screw to a torque of 7 Nm to secure the test specimen. 5.4.2.3 Raise the mass to the required height and retain it by the location pin. When the number plate and apparatus

31、have attained the required conditions, remove the pin and allow the mass to fall freely. 5.4.2.4 Calculate the impact resistance value by multiplying the height (in metres) of the fall by the mass (in kilograms) used. The impact energy shall be 7,5 J. 5.4.2.5 Examine the specimen for compliance with

32、 4.4.2. 5.5 Colour (white, black, blue, brown, green or red) and luminance factor test 5.5.1 Determine the chromaticity co-ordinates and luminance factors of the relevant areas of the test specimen by means of a spectrophotometer or other equally suitable colour-measuring device in accordance with C

33、IE 15, using standard illuminant D65 and 45/0 geometry. 5.5.2 Check for compliance with 4.4.3. 6 Packing The blank plates shall be packed so as to ensure that they are not damaged during normal handling, transportation and storage. 7 Marking 7.1 Each blank plate shall bear only the border as require

34、d in 4.1, 4.3.1 and the marking required in 7.2. The marking shall not interfere with the legibility of the licence number. 7.2 Each blank plate shall bear, in legible and indelible marking, the trade name or trademark and the batch number of the manufacturer of the blank plate in the left front bot

35、tom corner, in a space of height approximately 5 mm and of length approximately 50 mm. NOTE See annex C regarding the use of a tamper-proof security decal. SANS 1116-3:2008 Edition 3 7 Dimensions in millimetres Figure 1 Borders for number plates SANS 1116-3:2008 Edition 3 8 Figure 2 Apparatus for im

36、pactresistance testSANS 1116-3:2008 Edition 3 9 Figure 3 Number plate holding fixtureSANS 1116-3:2008 Edition 3 10 Annex A (informative) Quality verification of plastics blank plates for retro-reflective number plates When a purchaser requires ongoing verification of the quality of plastics blank pl

37、ates for retro-reflective number plates, it is suggested that, instead of concentrating solely on evaluation of the final product, he also direct his attention to the manufacturers quality system. In this connection it should be noted that SANS 9001 covers the provision of an integrated quality syst

38、em. SANS 1116-3:2008 Edition 3 11 Annex B (informative) Location of holes on number plates Figure B.1 Location of holes for number plates of 440 mm 120 mm SANS 1116-3:2008 Edition 3 12 Figure B.2 Location of holes for number plates of 250 mm 205 mm Figure B.3 Location of holes for number plates of 2

39、50 mm 165 mm SANS 1116-3:2008 Edition 3 13 Figure B.4 Location of holes for number plates of 520 mm 113 mm SANS 1116-3:2008 Edition 3 14 Annex C (informative) Security decal C.1 A tamper-proof security decal is issued to a manufacturer of blank plates by the relevant approving authority. Each decal

40、issued contains at least the name or permit number of such manufacturer for traceability. C.2 Such manufacturer then supplies a decal for each blank number plate sold to an embosser, and prints the permit number or name of the relevant embosser on the decal. Bibliography SANS 9001/ISO 9001, Quality management systems Requirements. SABS