SAE J 2859-2012 Hybrid III Large Male Drawing Package (Includes Access to Additional Content)《成人男子混合III型绘图软件包》.pdf

《SAE J 2859-2012 Hybrid III Large Male Drawing Package (Includes Access to Additional Content)《成人男子混合III型绘图软件包》.pdf》由会员分享，可在线阅读，更多相关《SAE J 2859-2012 Hybrid III Large Male Drawing Package (Includes Access to Additional Content)《成人男子混合III型绘图软件包》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Access to Additional Content for SAE J2859, Dated: September 2012 (Click here to view the publication) This Page is not part of the original publication This page has been added by IHS as a convenience to the user in order to provide access to additional content as authorized by the Copyright holde

2、r of this document Click the link(s) below to access the content and use normal procedures for downloading or opening the files. H-III95M_Drawing_Package_June_2012.pdf Information contained in the above is the property of the Copyright holder and all Notice of Disclaimer & Limitation of Liability of

3、 the Copyright holder apply. If you have any questions, or need technical assistance please contact IHS Support. IHS Additional Content Page _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of thi

4、s report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabili

5、zed, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or oth

6、erwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical

7、 Report, please visit http:/www.sae.org/technical/standards/J2859_201209SURFACE VEHICLE INFORMATION REPORT J2859 SEP2012 Issued 2012-09 Superseding JEA-32 MAR2005 Hybrid III Large Male Drawing Package RATIONALE The purpose of this document is to identify the drawings and parts required for the use o

8、f the Hybrid III Large Male Test Dummy. TABLE OF CONTENTS 1. SCOPE 1 2. REFERENCES 1 2.1 Applicable Documents 1 2.1.1 SAE Publications . 1 3. HYBRID III 95THLARGE MALE PARTS/DRAWING LIST 2 4. NOTES 3 4.1 Marginal Indicia . 13 1. SCOPE This SAE Surface Vehicle Information Report identifies and define

9、s the drawings and parts relating to the use of the Hybrid III Large Male Test Dummy. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.

10、1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J2860 Users Manual for the Hybrid III Large Male Test Dummy SAE J2859 Issued SEP2012 Page 2 of 13 3. HYBRI

11、D III 95THLARGE MALE PARTS/DRAWING LIST SAE J2859 Issued SEP2012 Page 3 of 13 SAE J2859 Issued SEP2012 Page 4 of 13 SAE J2859 Issued SEP2012 Page 5 of 13 SAE J2859 Issued SEP2012 Page 6 of 13 SAE J2859 Issued SEP2012 Page 7 of 13 SAE J2859 Issued SEP2012 Page 8 of 13 SAE J2859 Issued SEP2012 Page 9

12、of 13 SAE J2859 Issued SEP2012 Page 10 of 13 SAE J2859 Issued SEP2012 Page 11 of 13 SAE J2859 Issued SEP2012 Page 12 of 13 SAE J2859 Issued SEP2012 Page 13 of 13 4. NOTES 4.1 Marginal Indicia A change bar (I) located in the left margin is for the convenience of the user in locating areas where techn

13、ical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE DUMMY TESTING EQUIPMENT SUBCOMMITTEE OF THE SAE HUMAN BIOMECHANICS AND SIMULATION STANDARDS COMMITTEE