SAE AS 91001C-2012 NUT HEXAGON DRILLED BOSS CONNECTION CRES - UNS S30400《凸耳连接耐蚀钢制(CRES)钻孔六角螺母 UNS S30400》.pdf

《SAE AS 91001C-2012 NUT HEXAGON DRILLED BOSS CONNECTION CRES - UNS S30400《凸耳连接耐蚀钢制(CRES)钻孔六角螺母 UNS S30400》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 91001C-2012 NUT HEXAGON DRILLED BOSS CONNECTION CRES - UNS S30400《凸耳连接耐蚀钢制(CRES)钻孔六角螺母 UNS S30400》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD NUT, HEXAGON, DRILLED, BOSS CONNECTION, CRES - UNS S30400 AS91001Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, re

2、cording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-09REAFFIRMED 2007-06 REVISED 2012

3、-12THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.C FEDERAL SUPPLY CLASS 5310 AS91001SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel

4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y

5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS91001C RATIONALE REVISE THREAD SPECIFICATION TO AS8879, CORRECT VALUE FOR AB FOR -28 SIZE, AND GENERAL EDITIORIAL UPDATE. NOTICE THE INITIAL SAE

6、 PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9100B, AMENDMENT 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DoD CO

7、NTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - NUT AEROSPACE STANDARD AS91001 SHEET 2 OF 3 REV. C NUT, HEXAGON, DRILLED, BOSS CONNECTION, CRES - UNS S30400 TABLE 1 - PART NUMBERS AND DIMENSIONS PART NUMBER N

8、OM TUBE OD D - NOMINAL THREAD AF E MIN AB K MS9100-02 MS9100-03 MS9100-04 MS9100-05 MS9100-06 MS9100-07 MS9100-08 MS9100-09 MS9100-10 MS9100-11 MS9100-12 MS9100-14 MS9100-16 MS9100-18 MS9100-20 MS9100-24 MS9100-28 MS9100-32 .125 .188 .250 .312 .375 .438 .500 .562 .625 .688 .750 .875 1.000 1.125 1.25

9、0 1.500 1.750 2.000 .3125-24UNJF-3B .3750-24UNJF-3B .4375-20UNJF-3B .5000-20UNJF-3B .5625-18UNJF-3B .6250-18UNJF-3B .7500-16UNJF-3B .8125-16UNJ-3B .8750-14UNJF-3B 1.0000-12UNJF-3B 1.0625-12UNJ-3B 1.1875-12UNJ-3B 1.3125-12UNJ-3B 1.5000-12UNJ-3B 1.6250-12UNJ-3B 1.8750-12UNJ-3B 2.2500-12UNJ-3B 2.5000-1

10、2UNJ-3B .553 - .564 .616 - .627 .679 - .690 .741 - .752 .803 - .814 .865 - .877 .990 - 1.002 1.052 - 1.064 1.114 - 1.127 1.301 - 1.314 1.364 - 1.377 1.489 - 1.502 1.614 - 1.627 1.800 - 1.814 1.926 - 1.940 2.176 - 2.190 2.549 - 2.564 2.799 - 2.814 .623 .694 .766 .836 .907 .978 1.121 1.191 1.262 1.475

11、 1.547 1.690 1.833 2.045 2.189 2.474 2.899 3.185 .312 - .332 .375 - .395 .438 - .458 .500 - .520 .562 - .582 .625 - .645 .750 - .770 .812 - .832 .875 - .895 1.000 - 1.020 1.062 - 1.082 1.188 - 1.208 1.312 - 1.332 1.500 - 1.520 1.625 - 1.645 1.875 - 1.895 2.250 - 2.270 2.500 - 2.520 .240 - .260 .240

12、- .260 .271 - .291 .271 - .291 .287 - .307 .287 - .307 .334 - .354 .334 - .354 .381 - .401 .428 - .448 .428 - .448 .428 - .448 .428 - .448 .428 - .448 .428 - .448 .428 - .448 .428 - .448 .428 - .448 TABLE 1 - PART NUMBERS AND DIMENSIONS (CONTINUED) PART NUMBER NOM TUBE OD L MIN M N P T J APPROX MASS

13、 LB/100 MS9100-02 MS9100-03 MS9100-04 MS9100-05 MS9100-06 MS9100-07 MS9100-08 MS9100-09 MS9100-10 MS9100-11 MS9100-12 MS9100-14 MS9100-16 MS9100-18 MS9100-20 MS9100-24 MS9100-28 MS9100-32 .125 .188 .250 .312 .375 .438 .500 .562 .625 .688 .750 .875 1.000 1.125 1.250 1.500 1.750 2.000 .552 .615 .678 .

14、740 .802 .865 .990 1.052 1.115 1.302 1.365 1.490 1.615 1.802 1.928 2.178 2.552 2.802 .032 - .042 .032 - .042 .037 - .047 .037 - .047 .037 - .047 .037 - .047 .037 - .047 .037 - .047 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059 .049 - .059

15、 .478 - .488 .541 - .551 .603 - .613 .665 - .675 .728 - .738 .790 - .800 .915 - .925 .978 - .988 1.040 - 1.050 1.205 - 1.215 1.290 - 1.300 1.412 - 1.422 1.536 - 1.546 1.724 - 1.734 1.849 - 1.859 2.099 - 2.109 2.473 - 2.483 2.723 - 2.733 .125 .125 .140 .140 .148 .148 .172 .172 .195 .219 .219 .219 .21

16、9 .219 .219 .219 .219 .219 .240 .240 .305 .340 .370 .405 .470 .500 .540 .625 .660 .725 .790 .890 .960 1.095 1.295 1.425 .042 - .052 .042 - .052 .042 - .052 .050 - .060 .050 - .060 .050 - .060 .057 - .067 .057 - .067 .057 - .067 .065 - .075 .065 - .075 .065 - .075 .065 - .075 .065 - .075 .065 - .075

17、.065 - .075 .065 - .075 .065 - .075 1.28 1.50 1.98 2.21 2.62 2.93 4.10 4.38 5.49 8.83 9.34 10.50 11.65 13.44 14.78 17.36 21.48 24.40 AEROSPACE STANDARD AS91001 SHEET 3 OF 3 REV. C NUT, HEXAGON, DRILLED, BOSS CONNECTION, CRES - UNS S30400 NOTES: 1. MATERIAL: CORROSION RESISTANT STEEL AMS5639 (UNS S30

18、400). 2. CLEANING: FINISHED PARTS SHALL BE DEGREASED AND IMMERSED FOR NOT LESS THAN 20 MINUTES IN A SOLUTION OF NITRIC ACID (SP GR 1.42) AND 9 VOLUMES OF WATER AT ROOM TEMPERATURE. 3. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 1

19、25 MICROINCHES Ra. 4. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 5. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 6. MARKING: MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION IN ACCORDANCE WITH AS478, CLASS C. MULTIPLE MARKING OF BAR STOCK PERMISSIBLE PROVIDED POS

20、ITIVE IDENTIFICATION IS SHOWN. DASH NUMBERS MAY APPEAR ON ADJACENT FLATS. PARTS SHALL BE MARKED BEFORE THREADING. 7. DIMENSIONS ARE IN INCHES. 8. DO NOT USE UNASSIGNED PART NUMBERS. 9. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL RE

21、VISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.