SAE AS 39029 85A-2011 Contacts electrical connector pin crimp removable thermocouple (for AS50151 AS34501 series and MIL-DTL-83723 series II connectors)《热电偶压盖可拆式针形电气连接器触头(适用于AS5015.pdf

《SAE AS 39029 85A-2011 Contacts electrical connector pin crimp removable thermocouple (for AS50151 AS34501 series and MIL-DTL-83723 series II connectors)《热电偶压盖可拆式针形电气连接器触头(适用于AS5015.pdf》由会员分享，可在线阅读，更多相关《SAE AS 39029 85A-2011 Contacts electrical connector pin crimp removable thermocouple (for AS50151 AS34501 series and MIL-DTL-83723 series II connectors)《热电偶压盖可拆式针形电气连接器触头(适用于AS5015.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE (FOR AS50151 AS34501 SERIES AND MIL-DTL-83723 SERIES II CONNECTORS)AS39029/85Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or

2、transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.or

3、g SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-07REVISED 2011-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS39029/85SHEET 1 OF 4REV. APROCUREMENT SPECIFICATION: AS39029SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thes

4、tate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which

5、 time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/85ARATIONALE REVISE TO INCLUDE COMMENTS RECEIVED BY THE GOVERNMENT AND INDUST

6、RY, REMOVE GOVERNMENT JARGON, UPDATE REFERENCES, ALIGN SPECIFICATION WITH SAE GUIDELINES, AND REVIEW SPECIFICATION FOR KNOWN TECHNICAL PROBLEMS. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS39029. FIGURE 1 - PIN C

7、ONTACTS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/85SHEET 2 OF 4REV. A(R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE (FOR AS50151 AS34501 SERI

8、ES AND MIL-DTL-83723 SERIES II CONNECTORS) TABLE 1 - DIMENSIONS BIN CODE A B DDIAEDIAFDIAGDIAKMREF NDIASTMAXUDIA454THRU 457.300(7.62) .290(7.37) .079(2.01) .073(1.85) .042(1.07).036(.91) .068(1.73) .066(1.68) .133(3.38) .130(3.30) .103(2.62).101(2.57).280(7.11).250(6.35).923(23.44)N/A.631(16.03) .61

9、9(15.72) .015(.38) .0635(1.61).0615(1.56)458THRU 461.102(2.59) .098(2.49) .189(4.80) .186(4.72) .150(3.81).147(3.73)1.110(28.19).160(4.06) .155(3.94) .819(20.80) .808(20.52) .095(2.41).093(2.36)TABLE 2 - DESIGN CHARACTERISTICS BINCODES COLOR BANDS MATING ENDSIZEWIREBARREL SIZE TYPE CLASS1ST 2ND 3RD

10、454 YELLOW GREEN YELLOW 16 16 (SEE TABLE 4) B455 YELLOW GREEN GREEN 16 16 B 456 YELLOW GREEN BLUE 16 16 B 457 YELLOW GREEN VIOLET 16 16 B 458 YELLOW GREEN GRAY 12 12 B 459 YELLOW GREEN WHITE 12 12 B 460 YELLOW BLUE BLACK 12 12 B 461 YELLOW BLUE BROWN 12 12 B TABLE 3 - TOOLS BIN CODE BASIC CRIMPING T

11、OOL POSITIONER INSTALLING/REMOVAL TOOL 454thru 457M22520/1-01 M22520/7-01 M22520/1-02 BLUEM22520/7-03 M81969/14-03 458thru 461M22520/1-01 M22520/1-02 YELLOW M81969/14-04 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without li

12、cense from IHS-,-,-AEROSPACE STANDARD AS39029/85SHEET 3 OF 4REV. A(R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE (FOR AS50151 AS34501 SERIES AND MIL-DTL-83723 SERIES II CONNECTORS) TABLE 4 - MATERIALS, PLATING, AND TENSILE STRENGTH BIN CODE MATERIALS PLATING TENSILE STRENGTH

13、1/WIRE SIZEAXIAL LOAD (LBS)WIRE SIZE AXIAL LOAD (LBS)WIRE SIZE AXIAL LOAD (LBS)454 JN NONE 20 14 18 23 16 33 455 KN NONE 456 KP NONE 457 JP CADMIUM PLATE 2/458 JN NONE N/A N/A 14 53 12 85 459 KN NONE 460 KP NONE 461 JP CADMIUM PLATE 2/1/ APPLIES TO TYPE 1 WIRE PER MIL-DTL-5846 2/ CHROMATE CLEAR COAT

14、 TABLE 5 - PART NUMBER AND BIN CODE AS39029 PART NUMBER BINCODE SUPERSEDEDPART NUMBER(S) M39029/85-454 454 M39029/851616C1 M39029/85-455 455 M39029/851616C2 M39029/85-456 456 M39029/851616C3 M39029/85-457 457 M39029/851616C4 M39029/85-458 458 M39029/851212C1 M39029/85-459 459 M39029/851212C2 M39029/

15、85-460 460 M39029/851212C3 M39029/85-461 461 M39029/851212C4 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS39029. 1. DESIGN: CONTACTS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1, TABLES 1 AND 2. DIMENSIONS ARE IN INCHES, METRIC EQUIVALENTS ARE GIVEN F

16、OR GENERAL INFORMATION ONLY. DIMENSIONS SHOWN APPLY AFTER PLATING. SPHERICAL END DIMENSIONS SHALL CONFORM TO AS39029. 2. TOOLS: TOOLS REQUIRED FOR CRIMPING CONTACTS TO THE WIRE/CABLE AND THE INSTALLING/REMOVAL FROM THE CONNECTOR SHALL BE IN ACCORDANCE WITH TABLE 3. 3. PART NUMBERS: CONTACT PART NUMB

17、ERS SHALL BE IN ACCORDANCE WITH TABLE 5. SUPERSEDED PART NUMBERS ARE AS SPECIFIED. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/85SHEET 4 OF 4REV. A(R) CONTACTS, ELECTRI

18、CAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE (FOR AS50151 AS34501 SERIES AND MIL-DTL-83723 SERIES II CONNECTORS) 4. MATERIALS AND PLATING: SEE TABLE 4. 5. MECHANICAL: MECHANICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. TENSILE STRENGTH SHALL BE AS SHOWN IN TABLE 4. 6 ELECTRICAL: NOT REQU

19、IRED. 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. APPLICATION NOTES 1. CONTACT MATES DIRECTLY WITH AN AS39029/86 SOCKET CONTACT AS SHOWN IN TABLE 6. TABLE 6 - CONTACT MATING PART NUMBERS AS39029/85 BIN CODE MATING AS39029 SLASH SHEET/BIN CODE 454 M39029/86-510, -4

20、62455 M39029/86-511, -463456 M39029/86-512, -464457 M39029/86-513, -465458 M39029/86-466459 M39029/86-467460 M39029/86-468461 M39029/86-469 2. THE COMPOSITION DESIGNATIONS HAVE BEEN CHANGED AS LISTED BELOW: JN = TYPE J NEGATIVE (FORMERLY CONSTANTAN) KN = TYPE K NEGATIVE (FORMERLY ALUMEL) KP = TYPE K

21、 POSITIVE (FORMERLY CHROMEL) JP = TYPE J POSITIVE (FORMERLY IRON) SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CO

22、NVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-