SAE AS 14104D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED NARROW CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的窄幅低速自动校准自润滑式平纹轴承》.pdf

《SAE AS 14104D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED NARROW CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的窄幅低速自动校准自润滑式平纹轴承》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 14104D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED NARROW CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的窄幅低速自动校准自润滑式平纹轴承》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, CHAMFERED RACE, -65 TO +325 F AS14104Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, e

2、lectronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED

3、 1997-08REVISED 2010-06THIRD ANGLE PROJECTION CUSTODIAN: AIRFRAME CONTROL BEARINGS GROUP REV.DFEDERAL SUPPLY CLASS 3120 AS14104SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: AS81820SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengine

4、ering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed,

5、revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS14104DRATIONALE THE REASON FOR UPDATING THIS SPECIFICATION IS TO ADD THE ZINC NICKEL PLATING ONLY OPTION “ E

6、” . THE PLATING OPTION “ P “ WILL REMAIN AS ZINC NICKEL OR CADMIUM PLATING. .FIGURE 1 PART CONFIGURATION TABLE 1 - DIMENSIONS AND STRENGTHS PARTNO.* IB+.0000 .0005 ID* +.0000 .0005 H* .005 IMMIN Q (REF)W+.000.002STATIC LIMIT LOADOSCIL- LATINGLOADLBNO-LOADROTATIONAL BREAKAWAY TORQUE IN-LB WT LBMAX(RE

7、F)RADIALLBAXIALLB STANDARD *“K“ TYPE MS14104- 3 .1900 .5625 .218 .293 10 .281 3975 150 1500 0.25- 5.0 0-0.5 .020 MS14104- 4 .2500 .6562 .250 .364 10 .343 6040 430 3320 0.25- 5.0 0-0.5 .020 MS14104- 5 .3125 .7500 .281 .419 10 .375 8750 700 5460 0.25- 8.0 0-1.0 .030 MS14104- 6 .3750 .8125 .312 .475 9

8、.406 10 540 1100 6600 0.25- 8.0 0-1.0 .040 MS14104- 7 .4375 .9062 .343 .530 8 .437 13 200 1400 8050 0.25- 8.0 0-1.0 .050 MS14104- 8 .5000 1.0000 .390 .600 8 .500 17 900 2100 10 400 0.25- 8.0 0-1.0 .070 MS14104- 9 .5625 1.0937 .437 .670 8 .562 23 200 3680 13 000 0.25- 8.0 0-1.0 .090 MS14104-10 .6250

9、1.1875 .500 .739 8 .625 30 500 4720 16 450 0.25- 8.0 0-1.0 .120 MS14104-12 .7500 1.4375 .593 .920 8 .750 46 400 6750 23 600 0.25- 8.0 0-1.0 .210 MS14104-14 .8750 1.5625 .703 .980 8 .875 62 200 9350 30 250 0.25-12.0 0-2.0 .270 MS14104-16 1.0000 1.7500 .797 1.118 9 1.000 82 200 12 160 38 000 0.25-12.0

10、 0-2.0 .390 * SEE REQUIREMENT 5 “NO-LOAD TORQUE“ AND NOTE 8. * SEE NOTE 7 * FOR TYPE A BEARINGS, THE CORRESPONDING PART NUMBER WILL HAVE AN “A” DESIGNATION AFTER THE MSPART NUMBER (E.G., MS14104A-3). AEROSPACE STANDARD AS14104SHEET 2 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPE

11、ED, NARROW, CHAMFERED RACE, -65 TO +325 F TABLE 2 - OVERSIZE BEARING DIMENSIONS 1/ 2/RESTRICTED USAGE FOR REPAIR WORK ONLY .010 INCH AND .020 INCH OVERSIZE OUTSIDE DIAMETER FOR REPLACEMENT OF BEARINGS SHOWN ON SHEET 1 PARTNO. 3/NOMINAL SIZE1STOVERSIZE (.010) IDPARTNO. 3/NOMINAL SIZE2NDOVERSIZE (.020

12、) IDMS14104- 3T .1875 .5725 MS14104- 3U .1875 .5825 MS14104- 4T .2500 .6662 MS14104- 4U .2500 .6762 MS14104- 5T .3125 .7600 MS14104- 5U .3125 .7700 MS14104- 6T .3750 .8225 MS14104- 6U .3750 .8325 MS14104- 7T .4375 .9162 MS14104- 7U .4375 .9262 MS14104- 8T .5000 1.0100 MS14104- 8U .5000 1.0200 MS1410

13、4- 9T .5625 1.1037 MS14104- 9U .5625 1.1137 MS14104-10T .6250 1.1975 MS14104-10U .6250 1.2075 MS14104-12T .7500 1.4475 MS14104-12U .7500 1.4575 MS14104-14T .8750 1.5725 MS14104-14U .8750 1.5825 MS14104-16T 1.0000 1.7600 MS14104-16U 1.0000 1.7700 1/ BEFORE INITIATING A REPAIR PROCEDURE TO USE AN OVER

14、SIZE BEARING, APPROVAL FOR MODIFYING AND REIDENTIFYING THE BEARING HOUSING MUST BE OBTAINED FROM THE COGNIZANT ENGINEERING AUTHORITY. 2/ REFER TO NAS0331 FOR INSTALLATION PROCEDURE AND STAKING FORCES. 3/ FOR TYPE A BEARINGS, THE CORRESPONDING PART NUMBER WILL HAVE AN “A” DESIGNATION AFTER THE MS PAR

15、T NUMBER (E.G., MS14104A-3). REQUIREMENTS: 1. MATERIAL: BALL, 440C (AMS5630, AMS5880, OR AMS5618) OR PH13-8Mo AMS5629 H1000 (SEE NOTE 8 FOR P/N EXAMPLE AND DESIGNATION). RACE, 17-4PH (AMS5643). LINER, PTFE SHALL BE INCLUDED IN THE LINER. 2. SURFACE TEXTURE: BALL DIA Ra 8 MAX; BALL FACES, BALL BORE A

16、ND RACE DIA Ra 32 MAX; ALL OTHER METALLIC SURFACES Ra 125 MAX. LINER SURFACES ARE EXEMPT FROM SURFACE TEXTURE MEASUREMENTS. 3. HARDNESS: BALL, 440C HRC 55-62 OR PH13-8Mo HRC 43 MIN; RACE HRC 28 MIN/HRC 37 MAX BEFORE SWAGING. 4. SURFACE FINISH: RACE: PLATING, WHEN SPECIFIED, SHALL BE ZINC-NICKEL PLAT

17、ING PER AMS2417, TYPE 2, OR CADMIUM PLATING PER AMS-QQ-P-416, TYPE II, CLASS 2, WITH A THICKNESS RANGE OF 0.0003 TO 0.0006 INCHES. PLATE ON THE OUTSIDE DIAMETER SURFACE AND ON THE CHAMFER. PLATING RUNOUT SHALL OCCUR IN THE SIDE FACE AREA BETWEEN THE CHAMFER AND THE BALL. SEE NOTE 8 FOR P/N EXAMPLE A

18、ND DESIGNATION. BALL: PH13-8Mo, PASSIVATE PER AMS2700 OR ASTM A 967; 440C, PASSIVATE PER AMS2700 OR ASTM A 967, OPTIONAL. CHROME PLATING PER AMS2460 IS ALLOWED. BALL SHALL BE CHROME PLATED IF QUALIFIED WITH IT. 5. NO-LOAD TORQUE: WHEN THE LETTER “K” IS PRESENT IN THE PART NUMBER, LOWER VALUES OF NO-

19、LOAD TORQUE ARE SPECIFIED PER TABLE 1. IF THE MEASURED TORQUE OF A “K” TYPE BEARING IS LESS THAN 0.1 INCH-POUND, THE INTERNAL RADIAL PLAY SHALL BE MEASURED AND SHALL NOT EXCEED THE FOLLOWING: DASH NO. MAXIMUM RADIAL PLAY MAXIMUM AXIAL PLAY -3K THRU -12K 0.0007 INCH 0.0028 INCH -14K THRU -16K 0.0010

20、INCH 0.0040 INCH THE INTERNAL AXIAL PLAY SHALL BE MEASURED FOR ALL “K“ TYPE BEARINGS. AEROSPACE STANDARD AS14104SHEET 3 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, CHAMFERED RACE, -65 TO +325 F NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS

21、A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE; DECIMALS .010 AND ANGLES 0.5 DEGREES. 2. BREAK SHARP EDGES AND CORNERS AND REMOVE ALL BURRS AND SLIVERS. 3. THE -3 SIZE BEARING IS EXEMP

22、T FROM THE “RADIAL STATIC LIMIT LOAD“ TEST BECAUSE THE LOAD CAPACITY OF THE BEARING IS PIN CRITICAL. 4. WHEN TESTED TO THE FLUID CONTAMINATION AND SUB-ZERO TEMPERATURE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION, THE OSCILLATING LOAD SHALL BE DECREASED TO 75% OF THE SPECIFIED LOAD. 5. WHEN FLUIDS

23、AND ELEVATED TEMPERATURES (ABOVE 200 F) ARE BOTH PRESENT IN AN APPLICATION, THEN REDUCTIONS IN OPERATING LOADS OR BEARING LIFE MAY BE REQUIRED. 6. DASH NUMBER DESIGNATES NOMINAL BORE DIA IN SIXTEENTHS OF AN INCH. 7. DIMENSION “D” TO BE MET AFTER PLATING. DIMENSION “H“ TO BE MET BEFORE PLATING WHEN A

24、PPLICABLE. 8. EXAMPLE OF PART NO. MS14104 A -6 C P K T = .375 NOMINAL BORE DIA, PH13-8MO BALL MATERIAL, ZINC-NICKEL PLATED, LOW TORQUE, .010 INCH OVERSIZE O.D. (DIMENSION D). ABSENCE OF THE LETTERS “ T “ AND “ U “ INDICATE STANDARD OUTER DIAMETER ( D), (SEE TABLE 1). T = .010” OVERSIZE D (FOR REPAIR

25、 ONLY, SEE TABLE 2). U = .020” OVERSIZE D (FOR REPAIR ONLY, SEE TABLE 2). ABSENCE OF THE LETTER “ K “ INDICATES STANDARD BREAKAWAY TORQUE (SEE TABLE 1). LETTER “ K “ INDICATES LOW BREAKAWAY TORQUE (SEE TABLE 1). ABSENCE OF THE LETTER “ P “ INDICATES NO PLATING. LETTER “ P “ INDICATES ZINC-NICKEL OR

26、CADMIUM PLATING (SEE REQUIREMENT 4). LETTER “ E “ INDICATES ZINC-NICKEL PLATING ONLY (SEE REQUIREMENT 4). ABSENCE OF LETTER “ C “ INDICATES 440C BALL MATERIAL LETTER “ C “ INDICATES PH13-8Mo BALL MATERIAL SIZE BORE DIAMETER (DASH NO. FROM TABLE 1). ABSENCE OF THE LETTER “ A “ INDICATES TESTED TO 25,

27、000 CYCLES LETTER “ A “ INDICATES TESTED TO 100,000 CYCLES BASIC PART NUMBER. 9. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 10. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED

28、IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS DODISS SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 11. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL RE

29、VISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.