SAE AS 14102D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED WIDE CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的宽幅低速自动校准自润滑式平纹轴承》.pdf

《SAE AS 14102D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED WIDE CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的宽幅低速自动校准自润滑式平纹轴承》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 14102D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED WIDE CHAMFERED RACE -65 TO +325 DEGREES F《-65至+325℉倒棱种类的宽幅低速自动校准自润滑式平纹轴承》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, WIDE, CHAMFERED RACE, -65 TO +325 F AS14102Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, ele

2、ctronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1

3、997-08REVISED 2010-06THIRD ANGLE PROJECTION CUSTODIAN: AIRFRAME CONTROL BEARINGS GROUP REV.DFEDERAL SUPPLY CLASS 3120 AS14102SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: AS81820SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineer

4、ing sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, re

5、vised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS14102DRATIONALE THE REASON FOR UPDATING THIS SPECIFICATION IS TO ADD THE ZINC NICKEL PLATING ONLY OPTION “ E ”

6、. THE PLATING OPTION “ P “ WILL REMAIN AS ZINC NICKEL OR CADMIUM PLATING. FIGURE 1 PART CONFIGURATION TABLE 1 - DIMENSIONS AND STRENGTHS PARTNO.* IB+.0000 .0005 ID* +.0000 .0005 H* .005 IMMIN Q (REF)W+.000.002STATIC LIMIT LOADOSCIL-LATINGLOADLBNO-LOADROTATIONAL BREAKAWAY TORQUE IN-LB WT LBMAX(REF)RA

7、DIALLBAXIALLB STANDARD *“K“ TYPE MS14102- 3 .1900 .6250 .327 .300 15 .437 2500 1770 4900 0.25- 5.0 0-0.5 .031 MS14102- 4 .2500 .6250 .327 .300 15 .437 5500 1770 4900 0.25- 5.0 0-0.5 .031 MS14102- 5 .3125 .6875 .317 .360 14 .437 9400 1640 6050 0.25- 8.0 0-1.0 .035 MS14102- 6 .3750 .8125 .406 .466 8 .

8、500 13 700 2630 8310 0.25- 8.0 0-1.0 .060 MS14102- 7 .4375 .9375 .442 .537 10 .562 20 700 3650 11 750 0.25- 8.0 0-1.0 .080 MS14102- 8 .5000 1.0000 .505 .607 9 .625 21 400 4970 14 950 0.25- 8.0 0-1.0 .100 MS14102- 9 .5625 1.1250 .536 .721 10 .687 26 600 5370 18 100 0.25- 8.0 0-1.0 .135 MS14102-10 .62

9、50 1.1875 .567 .747 12 .750 29 000 6130 20 250 0.25- 8.0 0-1.0 .160 MS14102-12 .7500 1.3750 .630 .845 13 .875 37 000 7730 26 200 0.25- 8.0 0-1.0 .240 MS14102-14 .8750 1.6250 .755 .995 6 .875 65 200 10 800 33 600 0.25-12.0 0-2.0 .350 MS14102-16 1.0000 2.1250 1.005 1.269 12 1.375 104 000 19 300 56 250

10、 0.25-12.0 0-2.0 .970 * SEE REQUIREMENT 5 “NO-LOAD TORQUE“ AND NOTE 8. * SEE NOTE 7 * FOR TYPE A BEARINGS, THE CORRESPONDING PART NUMBER WILL HAVE AN “A” DESIGNATION AFTER THE MS PART NUMBER (E.G., MS14102A-3) AEROSPACE STANDARD AS14102SHEET 2 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNIN

11、G, LOW SPEED, WIDE, CHAMFERED RACE, -65 TO +325 F TABLE 2 - OVERSIZE BEARING DIMENSIONS 1/ 2/RESTRICTED USAGE FOR REPAIR WORK ONLY .010 INCH AND .020 INCH OVERSIZE OUTSIDE DIAMETER FOR REPLACEMENT OF BEARINGS SHOWN ON SHEET 1 PARTNO. 3/NOMINAL SIZE1STOVERSIZE (.010) IDPARTNO. 3/NOMINAL SIZE2NDOVERSI

12、ZE (.020) IDMS14102- 3T .1875 .6350 MS14102- 3U .1875 .6450 MS14102- 4T .2500 .6350 MS14102- 4U .2500 .6450 MS14102- 5T .3125 .6975 MS14102- 5U .3125 .7075 MS14102- 6T .3750 .8225 MS14102- 6U .3750 .8325 MS14102- 7T .4375 .9475 MS14102- 7U .4375 .9575 MS14102- 8T .5000 1.0100 MS14102- 8U .5000 1.020

13、0 MS14102- 9T .5625 1.1350 MS14102- 9U .5625 1.1450 MS14102-10T .6250 1.1975 MS14102-10U .6250 1.2075 MS14102-12T .7500 1.3850 MS14102-12U .7500 1.3950 MS14102-14T .8750 1.6350 MS14102-14U .8750 1.6450 MS14102-16T 1.0000 2.1350 MS14102-16U 1.0000 2.1450 1/ BEFORE INITIATING A REPAIR PROCEDURE TO USE

14、 AN OVERSIZE BEARING, APPROVAL FOR MODIFYING AND REIDENTIFYING THE BEARING HOUSING MUST BE OBTAINED FROM THE COGNIZANT ENGINEERING AUTHORITY. 2/ REFER TO NAS0331 FOR INSTALLATION PROCEDURE AND STAKING FORCES. 3/ FOR TYPE A BEARINGS, THE CORRESPONDING PART NUMBER WILL HAVE AN “A” DESIGNATION AFTER TH

15、E MS PART NUMBER (E.G., MS14102A-3). REQUIREMENTS: MATERIAL: BALL, 440C (AMS5630, AMS5880, OR AMS5618) OR PH13-8Mo AMS5629 H1000 (SEE NOTE 8 FOR P/N EXAMPLE AND DESIGNATION.). RACE, 17-4PH (AMS5643). LINER, PTFE SHALL BE INCLUDED IN THE LINER. 2. SURFACE TEXTURE: BALL DIA Ra 8 MAX; BALL FACES, BALL

16、BORE AND RACE DIA Ra 32 MAX; ALL OTHER METALLIC SURFACES Ra 125 MAX. LINER SURFACES ARE EXEMPT FROM SURFACE TEXTURE MEASUREMENTS. 3. HARDNESS: BALL, 440C HRC 55-62 OR PH13-8Mo HRC 43 MIN; RACE HRC 28 MIN/HRC 37 MAX BEFORE SWAGING. 4. SURFACE FINISH: RACE: PLATING, WHEN SPECIFIED, SHALL BE ZINC-NICKE

17、L PLATING PER AMS2417, TYPE 2, OR CADMIUM PLATING PER AMS-QQ-P-416, TYPE II, CLASS 2, WITH A THICKNESS RANGE OF 0.0003 TO 0.0006 INCHES. PLATE ON THE OUTSIDE DIAMETER SURFACE AND ON THE CHAMFER PLATING RUNOUT SHALL OCCUR IN SIDE FACE AREA BETWEEN THE CHAMFER AND THE BALL. SEE NOTE 8 FOR P/N EXAMPLE

18、AND DESIGNATION. BALL: PH13-8Mo, PASSIVATE PER AMS2700 OR ASTM A 967; 440C, PASSIVATE PER AMS2700 OR ASTM A 967, OPTIONAL. CHROME PLATING PER AMS2460 IS ALLOWED. BALL SHALL BE CHROME PLATED IF QUALIFIED WITH IT. 5. NO-LOAD TORQUE: WHEN THE LETTER “K” IS PRESENT IN THE PART NUMBER, LOWER VALUES OF NO

19、-LOAD TORQUE ARE SPECIFIED PER TABLE 1. IF THE MEASURED TORQUE OF A “K” TYPE BEARING IS LESS THAN 0.1 INCH-POUND, THE INTERNAL RADIAL PLAY SHALL BE MEASURED AND SHALL NOT EXCEED THE FOLLOWING: DASH NO. MAXIMUM RADIAL PLAY MAXIMUM AXIAL PLAY -3K THRU -12K 0.0007 INCH 0.0021 INCH -14K THRU -16K 0.0010

20、 INCH 0.0030 INCH THE INTERNAL AXIAL PLAY SHALL BE MEASURED FOR ALL “K“ TYPE BEARINGS. AEROSPACE STANDARD AS14102SHEET 3 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, WIDE, CHAMFERED RACE, -65 TO +325 F NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A

21、 PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE; DECIMALS .010 AND ANGLES 0.5 DEGREES. 2. BREAK SHARP EDGES AND CORNERS AND REMOVE ALL BURRS AND SLIVERS. 3. THE -3 SIZE BEARING IS EXEMPT

22、 FROM THE “RADIAL STATIC LIMIT LOAD“ TEST BECAUSE THE LOAD CAPACITY OF THE BEARING IS PIN CRITICAL. 4. WHEN TESTED TO THE FLUID CONTAMINATION AND SUB-ZERO TEMPERATURE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION, THE OSCILLATING LOAD SHALL BE DECREASED TO 75% OF THE SPECIFIED LOAD. 5. WHEN FLUIDS A

23、ND ELEVATED TEMPERATURES (ABOVE 200 F) ARE BOTH PRESENT IN AN APPLICATION, THEN REDUCTIONS IN OPERATING LOADS OR BEARING LIFE MAY BE REQUIRED. 6. DASH NUMBER DESIGNATES NOMINAL BORE DIA IN SIXTEENTHS OF AN INCH. 7. DIMENSION “D” TO BE MET AFTER PLATING. DIMENSION “H“ TO BE MET BEFORE PLATING WHEN AP

24、PLICABLE. 8. EXAMPLE OF PART NO. MS14102 A -6 C P K T = .375 NOMINAL BORE DIA, PH13-8MO BALL MATERIAL, ZINC-NICKEL PLATED, LOW TORQUE, .010 INCH OVERSIZE O.D. (DIMENSION D). ABSENCE OF THE LETTERS “ T “ AND “ U “ INDICATE STANDARD OUTER DIAMETER ( D), (SEE TABLE 1). T = .010” OVERSIZE D (FOR REPAIR

25、ONLY, SEE TABLE 2). U = .020” OVERSIZE D (FOR REPAIR ONLY, SEE TABLE 2). ABSENCE OF THE LETTER “ K “ INDICATES STANDARD BREAKAWAY TORQUE (SEE TABLE 1). LETTER “ K “ INDICATES LOW BREAKAWAY TORQUE (SEE TABLE 1). ABSENCE OF THE LETTER “ P “ INDICATES NO PLATING. LETTER “ P “ INDICATES ZINC-NICKEL OR C

26、ADMIUM PLATING (SEE REQUIREMENT 4). LETTER “E” INDICATES ZINC-NICKEL PLATING ONLY (SEE REQUIREMENT 4) ABSENCE OF LETTER “ C “ INDICATES 440C BALL MATERIAL LETTER “ C “ INDICATES PH13-8Mo BALL MATERIAL SIZE BORE DIAMETER (DASH NO. FROM TABLE 1). ABSENCE OF THE LETTER “ A “ INDICATES TESTED TO 25,000

27、CYCLES LETTER “ A “ INDICATES TESTED TO 100,000 CYCLES BASIC PART NUMBER. 9. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 10. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN T

28、HAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS DODISS SPECIFIED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 11. A CHANGE BAR ( L ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISI

29、ONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.