NAVY MIL-T-3595 B-1969 TUBING PHOSPHOR BRONZE (CDA NO 510) ROUND SEAMLESS [Use SAE AMS 4625G SAE AMS 4625G SAE AMS 4625F]《无缝(CDA NO 510)磷青铜油管 参见 SAE AMS 4625G SAE AMS 4625G SAE AMS.pdf

《NAVY MIL-T-3595 B-1969 TUBING PHOSPHOR BRONZE (CDA NO 510) ROUND SEAMLESS [Use SAE AMS 4625G SAE AMS 4625G SAE AMS 4625F]《无缝(CDA NO 510)磷青铜油管 参见 SAE AMS 4625G SAE AMS 4625G SAE AMS.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-3595 B-1969 TUBING PHOSPHOR BRONZE (CDA NO 510) ROUND SEAMLESS [Use SAE AMS 4625G SAE AMS 4625G SAE AMS 4625F]《无缝(CDA NO 510)磷青铜油管 参见 SAE AMS 4625G SAE AMS 4625G SAE AMS.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、RllL-T-3595B 14 July 1969 SUPERSE DING MIL-T-3595A 24 March 1952 MILITARY SPECIFICATION TUBING, PHOSPHOR BRONZE: (CDA NO. 510) ROUND, SEAMLESS This specification is mandatory for use by all Depart- ments and Agencies of the Department of Defense. 1. SCOPE l. l This specification covers round seamles

2、s phosphor bronze tubing, fur- nished in one composition and light and hard drawn tempers. 1.2 Classification - 1.2.1 Types - The tubing furnished under this specification shall be of the following types, as specified (see 6.2). Type 1 - Light Dram (1/4 Hard) Type 2 - Hard Drawn 2. APPLICABLE DOCUME

3、NTS 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent spec- ified herein. SPECIFICATIONS Military MIL- C- 3 993 Copper and Copper- Base Alloy Mill Products, Packaging of STANDARDS - Military MIL

4、-STD-129 Marking for Shipment and Storage Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-35958 47 947990b 0270450 Y m- MIL- T- 3 5 95 B STANDARDS Federal FED-STD-146 Tolerances for Copper and Copper Base Alloy Mill Products Fed. Test Method St

5、d. No. 151- Metals; Test Methods FED-STD-185 Continuous Identification Marking of Copper and Cop- per Base Alloy Mill Products (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should E obtained from the procuring

6、 activity or as directed by the contracting officer. ) 3. REQUIREMENTS 3.1 Material - The raw material used shall be such as to produce tubing in accordance with this specification. 3.2 Manufacture - The tubing shall be. seamless. 3.3 Chemical composition - The chemical composition of the tubes shal

7、l be as shown in Table I. Analysis shall regularly be made only for the elements spec- ifically mentioned in Table I. If the presence of other elements is suspected, or in- dicatedin the course of routine analysis,. further analysis shall be made either chem- ically or spectro-chemically to determin

8、e that the total of the other elements is not in excess of the percentage allowed. TABLE I CHEMICAL COMPOSITION COPPER PLUS TIN MINIMUM TIN PHOSPHORUS IRON LEAD ZINC PLUS PHOSPHORUS, PERCENT 3.5-5.8 0.03-0.35 O.id/ O.Od/ 0.3d/ 99.5 L/Maximum Provided by IHSNot for ResaleNo reproduction or networking

9、 permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-3575B 47 7777906 0270452 MIL-T-3595B ordered stock length and shall not exceed it by more than 1 inch. The permissible quantity and length of ends (short pi

10、eces) in any shiloment shall be as shown in 20a (4) of FED-STD-146 (see 6.2). 3.5.5 Squareness of end cuts - The departure from squareness of end cuts of tubes shall not exceed limits shown in 20a (6) of FED-STD-146. 3.5.6 Straightness - The maximum depth of arc of tubes ordered in straight lengths

11、shall not exceed limits shown in 20a (5) of FED-STD-146. 3.5.7 Roundness - For tubes ordered in straight lengths, the difference be- tween major and minor diameters shall not exceed limits shown in 20a (7) of FED- STD-146. 3.6 Cleaning - All tubes shall be thoroughly cleaned by pickling or other sui

12、table method before being presented for inspection. 3.7 Identification marking - Tubing shall be marked in accordance with FED-STD-185. The specification number, alloy number, and temper designation shall be included in the identification marking. 3.8 Woriananshig - All tubes shall be sound, of unif

13、orm quality and condi- tion, free from excessive nonmetallic inclusions, cracks, slivers, twists, seams, grooves, scale, damaged ends, buckles and other injurious defects. Inside and out- side surfaces shall be sufficiently free from irregularities to finish smooth inside and out by machining cuts n

14、ot to exceed 1/32 inch in depth. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection - Unless otherwise specified in the con- tract or purchase order, the supplier is respoqible for the performance of all in- spection requirements as specified herein. Except as otherwise specified in t

15、he coptract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Goveriiment. The Government reserves the right to perform any of the in- spections set forth in the specification where s

16、wh inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 - Lot - Unless otherwise specified by the procuring activity, a lot shall consist of all tubes of the same size submitted for inspection at the same time, and shall not exceed 5,000 pounds. 4.

17、3 Samples for chemical analysis - A sample for Government analysis shall be taken from each lot. The inspector shall select samples from O. 5 percent of the number of pieces in the lot, except that not less than two nor more than ten samples shall be taken from any lot. From the pieces selected, equ

18、al amounts of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-3595B 6. NOTES 6.1 Intended use - This material is used for the manufacture of can

19、non components by machining al surfaces of the tubing. It is not intended for ordinary tubing uses such as the conduction of fluids, 6.2 Ordering data - Procurement documents should specify the following: (a) Title, number, and date of the specification. (b) Type and size of tubing required (Two of

20、the following should be specified: inside diameter, outside diameter, wall thickness ). , (See 1.2.1, 3.5.1, and 3.5.3). (c) Level of packing required (see 5.1) and maximum gross weight of container. (d) Identification marking in addition to requirements of FED-STD-185 (see 3.7). (e) Special marking

21、, if rewired (see 5.2). (f) Whether specific lengths, specific lengths with ends, or stock lengths and stock lengths with ends are required (see 3.5.4.1, 3.5.4.2, and 3.5.4.3). 2 / - 6.3 Applicability of marking and packing requirements - The requirements for identification marking (see 3.7), for pa

22、cking (see 5.1) and marking for shipment (see 5; 2) apply ta direct shipment to Government activities and apply also to ship- ments between the manufacturer and the government prime contractor. Custodians : Preparing activity: Navy 7 AS Y,- Army - MR Navy - AS Air Force -11 Project No. 4710-0133 Review activities: Air Force - 82, 85 User activities: Army - ME Navy - OS * U. C. GOVERNMENT PRINTING OFFICE: 1969 -393-064/5-764 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-