NAVY MIL-C-46271 A (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M28A1 ASSEMBLY《航空器座椅弹射炮弹M28A1型组件》.pdf

《NAVY MIL-C-46271 A (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M28A1 ASSEMBLY《航空器座椅弹射炮弹M28A1型组件》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-46271 A (1)-1986 CARTRIDGE AIRCRAFT EJECTION SEAT CATAPULT M28A1 ASSEMBLY《航空器座椅弹射炮弹M28A1型组件》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、HIL-C-Y6271A (i) 13 H 9999906 0330565 3 - MIL-C-46271A(OS) AMENDMENT 1 14 October 1986 MILITARY SPECIFICATION - CARTRIDGE, AIRCRAFT EJECTION SEAT,. . . CATAPULT, M28A1 ASSEMBLY This amendment forms a part of Military Speciflcation MIL-C-46271A(MU), dated 8 February 1968, and is approved for use with

2、in the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1 Delete: “MIL-E-5272 . . .II in its entirety. Delete: “MIL-STD-639 . . .I in its entirety. Add : “MIL-STD-810 Environmental Test Methods and Engi

3、neering Gui del i nes“ . PAGE 2 Add: “2.2 Other publications. The following document forms a part of this specification to the extent specified herein, Unless otherwise specified, the issues of the document which are DOD adopted shall bethose listed in the issue of the DODISS specified in the solici

4、tation. specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the sol ici tation. Unless otherwise ANSI B46.1 (Application for copies should be addressed to the American National Standards Institute (ANSI), 1430

5、Broadway, NY 10018) (Nongovernment standards and other pub1 ications are normally available from the organization which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational servi ces. ) I Surface Texture (Surface Roughness, W

6、aviness and Lay) 3.3 Delete: l. . . MIL-E-5272, Procedure X11 . . .I and substitute II. . . MIL-STD-810, Method 514.3, Test Procedure I. Test Condition I - 3.2.5 . . . II . Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this docume

7、nt shou?d be addressed to: Standardization Branch (5241) I Indian Head, MD 20640-5000. Commanding Officer, Naval Ordnance Station, AMSC NIA Page 1 of 2 FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networkin

8、g permitted without license from IHS-,-,-MIL-C-4627 lA( OS) AMENDMENT 1 PAGE 5 4.3.2 Delete: “The Ordnan-ce Standard Finish Blocks prescribed in MIL-STD-639“ PAGE 14 and substitute: “The roughness comparison standards prescribed in ANSI B46.1“ 4.4.1 Delete: l. . . MIL-E-5272, Procedure X11“ and substitute I. . . MIL-STD-810, Method 514.3, Test Procedure I. Test Condition I - 3.2.5“. Preparing activity Navy - OS Project No. 1377-N839 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-