NAVY MIL-A-15344 J-1963 AMPLIFIER SYNCHRO SIGNAL《同步信号扩音器》.pdf

《NAVY MIL-A-15344 J-1963 AMPLIFIER SYNCHRO SIGNAL《同步信号扩音器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-A-15344 J-1963 AMPLIFIER SYNCHRO SIGNAL《同步信号扩音器》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-A-LSLILIJ 57 9997906 0015bY2 T Type MIL-A-1 5344J(NAVY) Synchro units Synchro excitation frequency cycles per second (C.P.S.). 7 June 1963 SUPERSEDING Output 60 and 400 60 or 400 (not both) 60 and 400 MIL-A-1 5344H(NAVY) 14 November 1961 1 -speed 18CT6 or 23CT6 18CT6 or23CT6 18CT4 or 23CT4 MILiT

2、ARY SPECIFICATION AMPLIFIER, SYNCHRO SIGNAL All interested bureaus of the Department of the Navy have concurred in the use of this specification. 1. SCOPE 1.1 Scope.- This specification covers the requirements for synchro signal amplifiers for the purpose of providing a means of increasing the capac

3、ity of a synchro signai transmission system, converting from 60 to 400 cycle synchro signai transmission or from 400 to 600 cycle synchro signai transmission, and to isolate reflected oscillations from the input synchro signal bus. 1.2 Classification.- The synchro signal amplifier shall be of the ty

4、pes listed in table I, as specified (see 6.2). Table I - Synchro signal amplifier. Input I I 400 18-speed I36-speed 18CT6 or 23CT6 18CT4 or 23CT4 Output 31TX4 I 23TX4 I“ 123TX4 23TX4 I ,;id I - - - 6Gmd - 31TX4 31TX4 , or 23CT6 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effe

5、ct on date of invitation for bids or request for proposal, form a part of the specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-1-983 ML-S-2335 - Synchros, 60 Cycle, 115 Volt. MIL-Q-9858 - Quality Control System Requirements. MIL-S-17087 - Servo Motors, 2 Phase, 400 Cycles. M

6、IL-E-17555 - Electronic and Electrical Equipment and Associated Repair Parts, Preparation MIL-S-20708 - Synchros, 60 and 400 Cycle, General Specification. - Interior Communication Equipment, Naval Shipboard; Basic Design Requirements for. for Delivery of. STANDARDS MILITARY MIL-STD-710 - Synchros, 6

7、0 and 400 Cycle. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A- 15344J(NAVY) DRAWINGS BUREAU OF SHIPS 900O-S6202-73907 - Switchboard. indicator Light - 2, Lamp - SPF- Type B27A. (Copies of specifications, standards, drawings, and publications

8、 required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contract- ing officer. ) 2.2 Other publications. - The following document forms a part of this specification to the extent spec- ified herein. Unless otherwis

9、e indicated, the issue in effect on date of invitation for bids or request for proposal shall apply: OFFICIAL CLASSIFICATION COMMITTEE Uniform Freight Classification Rules. (Application for copies should be addressed to Officiai Classification Committee, 1 Park Avenue at 33rd St., New York 16, New Y

10、ork.) 3. REQUIREMENTS 3.1 Qualification. - The synchro signal amplifier equipment furnished under this specification shall be a product which has been tested, and passed the qualification tests specified herein, and has been listed on or approved for listing on the applicable qualified products list

11、. 3.2 Description. - The synchro signai amplifier shall consist of an amplifier, synchro control trans- formers (see table I); one alternating current (a.c.) two phase servo motor with necessary gear train for driving the synchro rotors, as specified in 3.7.2; and output synchro signal generators of

12、 appropriate size as specified (see 6.2) all assembled in a dripproof enclosure (see 3.6.1) with the necessary operating controls (see 3.6.4), indicator lights (see 3.7.4), alarm relays (see 3.7.5) and capacitors (see 3.7.6). 3.3 Operation. - The typical cycle of operation of the synchro signal ampl

13、ifier is as follows: A synchro signal, such as that obtained from a master gyrocompass is transmitted to the synchro control transformers (CTs) in the synchro amplifier. The signal received by the synchro control transformers is fed to the ampli- fier unit where it is intensified and used to actuate

14、 the follow-up motor which, through gearing, turns the synchro control transformer rotors until the induced voltages are reduced to a null, thereby stopping the follow-up action. At the same time the follow-up motor also drives, through gearing, the output synchro signal generator rotors. The output

15、 synchro signal generators actuate the remote network of synchro signal receivers which are then displaced the same angular amount as the input synchro signal. 3.4 General featur.es. - in addition to the requirements specified herein, the equipment shall be in accordance with MIL-1-983 except for th

16、e following paragraphs. (Whenever a requirement of MIL-1-983 conflicts with a requirement of this specification, the requirement of this specification shall govern): Universal mounting Stand mounting Panel mounting Bulkhead mounting Tumbling Gunblast Depth charge Dial illumination Repair parts (elec

17、tronic) Salt spray 3.5 Design.- The synchro signal amplifier shall be so designed that vibration, shock, or acceleration, which may be encountered in service aboard Naval ships, will not adversely affect the accuracy of the equipment, nor derange any part of the equipment beyond normal adjustment at

18、 sea. All parts except those necessary in electromagnetic circuits, ball bearings, shafts, thrust plates, and similar application where stremw hardness is essential shall be constructed of nonferrous, nonmagnetic materials. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

19、ut license from IHS-,-,-MIL-A-1 5344J(NAW) 3.6 Mechanical features. - 3.6.1 Enclosure.- All parts required for the proper operation of the synchro signai amplifier shall be mounted in an enclosing case (degree of enclosure dripproof) designed for bulkhead, platform, and stack mounting (maximum of fo

20、ur units mounted one on top of another). Provision shall be made for the protection of gears from dust. Mounting and external wiring ofthe equipmentshall beaccompished, insofar as practical, without having to remove the amplifier or synchro unit from the enclosure and without having to expose the ge

21、ars to dust. A removable plate (a minimum of 4 inches by 8 inches by 1/8 inch) for the installation of stuffing tubes shall be provided on both sides of each enclosure. The enclosing case shall consist of an alumi- num angle or channel framework, suitably welded to form a structure of adequate stren

22、gth to support all sub- assemblies. A wrap-around or similar covering of aluminum shall be provided around the framework. inter- nal subassemblies shall not be supported by the aluminum covering. The case shall be sufficiently ventilated to meet the operating temperature requirements herein. Ventila

23、tion may be achieved by louvers in the ends and front cover, by screened openings in the bottom of the case and by umbrella type covered openings in the top. 3.6.2 Accessibility. - All units and subassemblies of the equipment shall be easily accessible for repair and adjustment. The access door to t

24、he amplifier shall be equipped with hinges and supporting straps or anchors and supporting chains so that it may act as a service platform for the amplifier internal assemblies. Protection of the internal subassemblies shall be provided in accordance with MIL-1-983. Supporting rods shall be furnishe

25、d on the amplifier and servo units to allow repair work without the units resting on electrical components, electrical connections or on components that may be disarranged or otherwise damaged. A schematic diagram of the amplifier shall be attached to the inside of this door. Knurled knob captive sc

26、rews with a screwdriver slot shall be used on all covers that require removal or opening for operating adjustments. no case shall the maximum weight of the various types exceed that specified in table D. Maximum size shall not exceed 3 cubic feet for any type of synchro amplifier. 3.6.3 Weight and s

27、ize. - The weight of a synchro signal amplifier shall be kept to a minimum and in Table II - Weights. Type Maximum weight with full complement of largest synchros required by this specification E F E F Pounds 120 when structureborne noise 120) limits are not imposed. I 130 when structureborne noise

28、1 130) limits are imposed. 3.6.4 Controls and indicators. - The following operating controls and indicator lights shall be provided on the front of the enclosure: (a) Alarm relay switch (see 3.7.5). (b) Power and follow-up indicator lights (see 3.7.4). (c) Fuseholders. 3.6.4.1 An indicator dial(s) (

29、see 3.7.15) shall be visible through the front of the enclosure. 3.7 Electrical features. - 3.7.1 Amplifier unit. - The amplifier unit shall be electron tube, transistor or magnetic type and shall consist of the necessary items arranged on a removable chassis to provide control of the a.c. two-phase

30、 motor. Each line supplying power to the amplifier unit and the servo motor (see 3.7.3) shall be properly fused within the synchro amplifier. The total power required shall no? exceed 150 watts. The amplifier 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

31、 IHS-,-,-MIL-A- 15344J(NAVY) chassis shall be grounded to the case. and a B minus bus isolated from the chassis shall be provided for the servo amplifier and shall be positively connected (bonded) to the case of the synchro amplifier a! one phys- ical point only. An isolation transformer or equivale

32、nt isolation shall be used between the output power of the servo amplifier and the servo motor control field. 3.7.2 Synchro unit.- The synchro unit shall consist of the input synchro control transformers, a two- phase servo motor, gear trains, and the output synchro signal generators to provide for

33、the receipt of the input synchro signal from the master gyrocompass, or other synchro signal source, and the retransmission of the synchro signal to a network of synchro signal receivers. The plate supporting the synchro control transformers, servo motor, and synchro signal generators shall be so ar

34、ranged as to be removable. All synchro transmitters and control transformers shall be contractor furnished material in accordance with MIL-S-20708 or MIL-S-2335, if for size 6 or 7 synchros, and in accordance with MIL-STD-710. 3.7.3 Servo motor. - The servo motor shall be a two-phase low-inertia des

35、ign with grease sealed ball bearings, and shall be contractor furnished. The choice of servo-motor shall be approved by the bureau or agency concerned. Specification MIL-S-17087 shall apply for 400-cycle servo motors. Sixty cycle servo motors shall have temperature ratings comparable to those for 40

36、0-cycle servo motors. of failure inmm follow-up action, (b) input power, (c) output 60-cycle synchro excitation power and (d) output 400-cycle synchro excitation power. An illuminated light shall indicate normal operation; and extinguished light - failure. The output synchro excitation lights shall

37、be omitted and the openings in the front of the enclosure shall be concealed with a cover, or by other means when synchro differential units are substituted for synchro generators. indicator lights shall be in accordance with Drawing 9000-S6202- 73907. 3.7.4 Indicator 1 hts - Indicator lights having

38、 white lenses shall be provided to give a single indication 3.7.5 Alarm relay and switch. - An alarm relay shall be provided to indicate failure of the servo system to follow the input synchro signal, loss of power to the servo amplifier and loss of output 60 and 400-cycle synchro power. The relay c

39、ontacts shall be designed to carry 5 amperes at 0.5 power factor, 115 volts 60 or 400 cycles a. c. , and shall be connected to terminal connections for an external alarm circuit. The relay shall operate when the servo error exceeds approximately 2.5 degrees or upon loss of input power or upon loss o

40、f output synchro excitation power. An alarm relay switch shall be provided, and shall be con- nected so that the alarm relay will operate the external alarm circuit as specified in table m. An example of an acceptable circuit is shown on figure 1. When only differential synchros constitute the 60-cy

41、cle or 400- cycle output synchros, the alarm circuitry and relays normally used for 60-cycle or 400-cycle output synchro generator power failure shall be omitted. Table I - Alarm relay and switch connection. Nominal values of error follow-up - 2.5“ or less 2.5“ or less E - 1 Alarm switch Input and o

42、utput syn- chro excitation Off External alarm circuit De-energized Energized De-energized a Ene ized 3.7.6 Synchro capacitors. - The correct synchro capacitors shall be provided by the contractor (mounted within the enclosure) for all synchro control transformers. The value of the capacitor elements

43、 shall be determined by the contractor for the particular synchros to be used. The capacitor elements shall be rated for 600 volts d.c. or greater. Each synchro capacitor shall have the capacitance of its three capacitor elements balanced within 1 percent as measured by the divergence of the capacit

44、ance of any one leg from the arithmetical mean of the three. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-A-15344i 57 999990b 0035bgb 7 MIL- A- l 5344 J(NAVY) EXCITATION * ERRORI Il5 v. - therefore an error proportionate to the magnitude of

45、 the measured voltage exists in the synchro amplifier. in order to determine the error in terms of degrees and minutes for the purpose of this test, the angular deviations of the rotor of the 5CT control transformer with respect to the rotor of the synchro transmitter shall be calibrated in terms of

46、 voltage values as determined from the oscilloscope, oscillograph or equivalent device specified herein. Accuracy tests on synchro amplifiers shall be made for static and dynamic conditions in accordance with 4.7.1.1.1 and 4.7.1.1.2. When synchro differential transmitters only are required as output

47、 synchros of production synchro ampli- fiers the follow-up error (see 4.7.1.2) shall be substituted for the overall error. When 400-cycle syn- chros only are required in the output of the production synchro amplifiers the accuracy test shall be made using a 400-cycle output synchro and a 400-cycle c

48、ontrol transformer or the 5CT as a 400-cycle synchro, Accuracy of production synchro amplifiers shall be determined using just the synchros to be delivered in the equipment. For synchro amplifiers operating at speeds different from 1 and 36 for their inputs and outputs, the test procedure shall be s

49、imilar to that specified above. Each and every production synchro amplifier shall not be tested for accuracy for all of the different input and output speed variations of which the synchro amplifier is capable. For instance, a synchro amplifier with 1 and 36-speed input and output shall be tested with a 1 and 36-speed input in the manner described above and shall not be tested for a 1-speed input only, or for a 36-speed input only, or for a 2-speed input only. 4.7.1.1.1 Static accuracy. - Th