NAVY A-A-59470-1999 CABINETS MODULAR DRAWER STORAGE (NAVAL SHIPBOARD) [Superseded NAVY MIL-C-24697 CANC NOTICE 1 NAVY MIL-C-24697]《[代替 海军军事标准-C-24697 CANC 注意 1 海军军事标准-C-24697]海军船标准.pdf

《NAVY A-A-59470-1999 CABINETS MODULAR DRAWER STORAGE (NAVAL SHIPBOARD) [Superseded NAVY MIL-C-24697 CANC NOTICE 1 NAVY MIL-C-24697]《[代替 海军军事标准-C-24697 CANC 注意 1 海军军事标准-C-24697]海军船标准.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-59470-1999 CABINETS MODULAR DRAWER STORAGE (NAVAL SHIPBOARD) [Superseded NAVY MIL-C-24697 CANC NOTICE 1 NAVY MIL-C-24697]《[代替 海军军事标准-C-24697 CANC 注意 1 海军军事标准-C-24697]海军船标准.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-59470 9038054 0012213 TT8 Cabinet Height of class 1 cabinets Size 1 27.0 f -250 2 30.0 f .250 3 33.0 k .250 4 44.0 I .250 5 59.0 f .250 IINCH-POUND I A-A- 5947 O 23 June 1999 SUPERSEDING 29 February 1988 MIL-C-24697 Height of class 2 cabinets 24.75 I .250 27.75 f .250 30.75 f .250 41.75 f .250 5

2、6.75 f .250 COMMERCIAL ITEM DESCRIPTION CABINETS, MODULAR.DRAWER STORAGE (NAVAL SHIPBOARD) The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE This commercial item description (CID) describes modular drawer storage cabinet

3、s with various combinations of drawer sizes in various sizes of cabinet housings to be used for storing parts, tools, and supp.lies for Naval shipboard use. 2. CLASSIFICATION 2.1 Cabinet housinq. Cabinet housings (excluding drawer handles and protruding lock-in and lock-out devices) shall be of the

4、following types, styles, classes, and sizes shown in Table I. Type 1: Narrow width - 22.5 f 0.063 inches Type 2: Standard width - 30 k 0.063 inches Style 1: Narrow.depth - 21.375 It 0.063 inches. Style 2: Standard depth - 27.75 f 0.063 inches Class 1: With fork-lift base Class 2: Without fork-lift b

5、ase Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other data which may improve this document should be sent to: Commander, Naval Sea Systems Command, 2531 Jefferson Davis Highway, Arlington, VA 22242-5160. AMSC N/A FSC 7125 DISTRIBUTION STATEMENT A. Approv

6、ed for public release; distribution is unlimited. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-57470 m 90Lf305Y O012212 734 m A-A-5947 O TABLE II. Number of drawer modules for each cabinet size aules ri

7、iyri i 35 or 36 modules high 49 or E 3 A TABLE III. SDecial use aDDlications for class 2 modular drawer storaue cabinets used as Dedestalc for workinu surfaces inches. (2) Thickness of customer-provided top is generally 1.50 f inches. .250 2.3 Cabinet drawers. styles, and sizes as specified. Each ca

8、binet drawer shall be furnished with a lock-in / lock-out device as specified in 3.1.3.4. Sizes of.drawers are given in Table IV. Cabinet drawers shall be of the following types, Type 1: Narrow width Type 2: Standard width Style 1: Narrow depth Style 2: Standard depth Size: A through O (See Table IV

9、) TABLE IV. Cabinet drawer dimensions (inches) Dwr front I.125 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59470 E 9018054 0012213 870 E . A-A-5 947 O 2.4 Manufacturers drawer substitution. When specified, the manufacturer may interchange

10、 drawers within the following pairs to account for minor variations in cabinets: A/%, C/D, E/F, and H/I. 3. SALIENT CHARACTERISTICS 3.1 Desian and construction. 3.1.1 Cabinet. The cabinet shall be modular in construction, fabricated of cold or hot rolled commercial quality steel. 3.1.1.1 Cabinet Dan

11、els. Top, bottom, front, side and back panels; all shall be formed with 90 degree flanges and shall be of thicknesses to meet load requirements (see 3.1.2.3). The front flange shall have an additional return flange for rigidity and safety and shall form the front of the cabinet case. The side and ba

12、ck panels shall be jointed on the back, or the joint may be centrally located on the back panel. All cabinet panels shall be resistance welded. The first and last welds in a series shall be not less than 3 inches from each end of the panel side. 3.1.1.2 Cabinet fork-lift base. The cabinet base shall

13、 be of two formed steel members, each with a thickness of not less than 13-gauge steel, 2.250 k .250 inches in height, extending from the front to the rear of the cabinet. The members shall be suitable for allowing forklift entry from the front or rear of the cabinet and shall be attached to the bot

14、tom panel of the cabinet with resistance or mig welds. Each cabinet base shall be equipped with two face covers, fastened with corrosion resistant snaps or screws to cover the front and rear fork-lift openings when not in use. 3.1.2 Reinforcina members. 3.1.2.1 Front. rear and side vertical members.

15、 Each member for the front, rear and side vertical reinforcing shall be formed members with the thickness of each developed to meet load bearing requirements. The front column shall be resistance welded to the side panel, and the flanges of the rear members shall be resistance welded to the side and

16、 back panel. The front and rear vertical members, formed with not less than two bends, shall contain a series of evenly spaced, precisely located holes or slots, constructed and aligned for mounting the drawer carriage assemblies. The side vertical member shall be formed, without holes or slots, and

17、 resistance welded to each side panel. 3.1.2.2 Carriase assemblv. The carriage brackets shall be right-hand and left-hand, of modular construction to permit interchangeability to the upper or lower position within a cabinet or to any other cabinet in the lots fabricated by the same manufacturer for

18、this acquisition. The carriage brackets shall be internally engaged into the slots in the rear interior vertical reinforcing members. 3.1.2.3 arriaae susDension. The carriage shall be modular in construction to permit interchangeability within the cabinet and provide for the attachment of drawer rol

19、lers and out stops. Each carriage shall have two carriage stops designed to stop a drawer loaded at the rated capacity of 400 lbs. when opened at the rate of 15 inches per second. 3.1.3 Drawers. 3.1.3.1 D-. Drawer dimensions shall be as shown in Table II. 3.1.3.2 Construction. The drawers shall be m

20、odular in construction and manufactured in standard sizes with respect to height and width. Module height shall be 0.875 f 0.125 inches. The interior dimensions of the drawer. shall be as shown in Table 4 and on Figure 1. The drawers and any standard drawer accessories shall be interchangeable withi

21、n their own cabinet and with any 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59470 m q018054 001224 707 m A-A-59470 Drawer size At B C, D other cabinet of the same type from the same manufacturer. Each drawer shall be provided with multiple

22、 and equally spaced holes and slots to secure drawer partitions and dividers. Steel rails shall be securely welded to the drawer sides to provide rigid support of the drawer as it travels on the roller system of the carriage. Each drawer shall fully extend in the open position, unsupported, with lef

23、t-hand and right-hand stops (see 3.1.2.3) to prevent the drawer from traveling past the supporting range of the carriage. 3.1.3.3 Drawer hardware. Each drawer shall be provided with an extruded aluminum handle fastened to the drawer front. The extrusion shall be constructed for the insertion of full

24、 length label strips and protective clear plastic strip covers, to allow easy reading and identification. Each end of the extruded handle shall be capped or configured for safety and retention of labels and covers. The handle length shall run approximately 75 percent of the width of the drawer and p

25、rovide a comfortable finger entry. Height of drawer partition and divider (inches) 1.875 f 0.125 2.875 f 0.125 3.1.3.4 Drawer lock-in and lock-out device. Drawers shall be provided with a spring-loaded, stainless steelmechanism for automatic lock-in and lock-out protection, with the drawer closed or

26、 fully extended, respectively, and loaded to rated capacity. The lock-in and lock-out device for each drawer shall be independent of any other drawer. An integral operating lever to activate the mechanism shall protrude through an opening in the drawer front, adjacent to the right or left end of the

27、 drawer handle. (Shipboard requirement, see 7.2) E, F 3.1.3.5 Cabinet lock. When specified (see 7.11, a key-operated cabinet lock shall be installed in the top front of each cabinet housing. The single key- operated lock shall lock and unlock all drawers in the cabinet. 3.1.4 Drawer wartitions and d

28、ividers. 3.1.4.1 Partitions. When specified (see 7.11, drawer partitions, modular in construction shall be provided, (see Figure 2), to compartmentalize each drawer into storage sections; front-to-back and left-to-right. Each partition shall be furnished in one length and slotted to match the slots

29、on the inner walls of the drawer. The partitions shall be of steel, flanged on the bottom and provided with holes to allow attachment to the bottom of the drawer with two stainless steel sheet metal screws. Partition length shall be 0.125 I .O31 inches less than the inside drawer dimension. The heig

30、ht shall Correspond to the drawer size specified in Table V. TABLE V. Drawer Dartition and divider heicrhts accordina to drawer size. 4.500 f 0.125 G, Hn 1, J, K, L, M, N, O 5.250 f 0.125 3.1.4.2 Dividers. When specified, vertical drawer dividers, Style A or B (see Figure 2) shall be provided. Divid

31、ers shall be modular in construction and of sufficient strength to contain the materials stowed in the drawer. The top 0.5 inches shall be formed; not less than 15 to 30 degrees from the vertical, to allow for placement of the labels. The bottom corner edges shall allow for clearance of partition fl

32、anges. Dividers shall be available in lengths (f.500 inches) of 3.500 inches, 4.625 inches, 6.250 inches, 8.000 inches, 9.500 inches, and 12.500 inches for each drawerThe.height of the divider shall correspond to the drawer size specified in Table V. 3.2 Inclined. The unit shall operate satisfactori

33、ly, in accordance with the requirements of this CID (such as the drawer remaining closed to prevent the loss of contents) when inclined at angles of 20 (30 when 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-57470 9 90115054 0012215 by3 II A-

34、A-5947 O specified for submarines) each side of the vertical, in each of two vertical planes at right angles to each other. (Shipboard requirement, see 7.21 3.3 Interchanaeabilitv. All parts of components or assemblies of the cabinet having the same manufacturers part number shall be manufactured to

35、 standards and tolerances that will provide for the interchangeability of respective replacement parts between assemblies and components of the cabinet without modification of the part or the cabinet. 3.4 Physical size limitations. The type 1 unit shall pass or shall be provided with a means of disa

36、ssembly so that it can pass thr0ugh.a surface ship access measuring 26 x 66 inches with 8-inch radius corners or a submarine access measuring 30 inches in diameter. (Shipboard requirement, see 7.2) 3.5 Label Dlates. instruction plate, both attached to the front of the unit. They shall be readily vis

37、ible during normal operating use and shall not adversely affect the life and utility of the unit. The data nameplate shall contain the manufacturers name, model, serial number, date manufactured, and any other information needed to uniquely identify the unit. The instruction plate shall contain safe

38、ty and operational information as applicable. 3.6 Environmental suitability. The unit shall be capable of withstanding ships vibration and motion. Controls, switches, moving parts, and electrical circuits shall operate under shipboard conditions without malfunction, binding, excessive looseness, or

39、damage, when tested in accordance with MIL- STD-167-1, type I equipment. The unit shall be secured to the test machine in the same manner that it will be secured on shipboard. (Shipboard requirement, see 7.2) The unit shall be provided with a data nameplate and an 4. REGULATORY REQUIREMENTS The offe

40、ror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The product provided shall meet the salient characteristics of this CID, conf

41、orm to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market, or the same product that has been delivered to the Government for shipboard use on a previous procurement. The Government reserves the rig

42、ht to require proof of such compliance. 6. PACKAGING Preservation, packing, and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 Orderina data. 0 Title, number, and date of this CID 0 Quantity, type,style, class, and sizes of cabinets Quantity, type, style, size, and con

43、figuration of drawers Specify locks 0 Specify “ keyed alike“ , for multiple cabinets with identical locks Specify master keyed“ , for single key access to multiple cabinets 0 Quantity and Size of drawer dividers with different locks 5 Provided by IHSNot for ResaleNo reproduction or networking permit

44、ted without license from IHS-,-,-A-A- 5 9 47 O 0 Quantity and Size of drawer partitions e When required, the unit shall meet shock Grade B requirements of MIL- e When required, manuals shall be in accordance with ASTM F760 S-901 7.2 $hiDboard remirement. Whenever a “ (Shipboard requirement)“ is incl

45、uded in a paragraph under SALIENT CHARACTERISTICS, it is meant that the requirement is something that is not normally offered to the commercial market by the manufacturer. 7.3 Sources of documents. 7.3.1 Militam documents. Copies of documents required by manufacturers in connection with specific acq

46、uisition functions should be obtained from the contracting activity or as directed by the contracting officer. MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment MIL-S-9 O 1 - Shock Tests, H.I. (High Impact) Shipboard Machinery, Equipment, Systems 7.3.2 American Societv for TestincT and Ma

47、terials (ASTM) Standards. ASTM Standards are available from the American Society of Testing and Materials, 100 Barr Harbor Drive, West Conshohoken, PA 19428-2959. ASTM F760 - Food Service Equipment Manuals 7.4 Suaaested sources of sumlv. Manufacturers of products known to meet the requirements of th

48、is CID are listed below. However, competition is not limited to these companies. Stanley Storage Systems 11 Grammes Road P.O. Box 1151 Allentown, PA 18105-11.51 Equipto, Corporate Offices 4819 Maple Ave. Dallas, Texas 75219 Lyon Metal Products P.O. Box 671 Aurora, IL 60507-0671 MILITARY INTERESTS: C

49、ustodians: Navy - SH Army - GL CIVIL AGENCY COORDINATING ACTIVITIES: GSA - FSS Preparing activity: Navy - SH (Project 7125-0154) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59470 17.94 IN - H 9018054 0012217 41b 6 i A-A-5947 O TYPE I - CABINET DRAWER 18.75 IN. STYLE 1 25.31 IN. STYLE 2 TYPE II - CABINET DRAWER FIGURE 1. W es 1 and 2 cabinet drawers 7 Provided by IHSNot for ResaleNo reproduction or