NAVISTAR MPAPS S-R-5 101-GS-2015 Fuses C General Specifications (Noun Code C 3660).pdf

《NAVISTAR MPAPS S-R-5 101-GS-2015 Fuses C General Specifications (Noun Code C 3660).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS S-R-5 101-GS-2015 Fuses C General Specifications (Noun Code C 3660).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 1 of 3 NAVISTAR, INC. Material, Parts, and Process Specifications (

2、MPAPS) NUMBER: MPAPS S-R-5.101-GS Former Designation: ESP-R-5.101-GS TITLE: Fuses General Specifications (Noun Code 3660) CURRENT REV No.: 1506 DATE: June 2015 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: ESP-R-5.101-GS - September 2000 PRINTED COPIES OF TH

3、IS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices

4、 and to determine the applicability of regulatory limits prior to use. Change Notice: Changed to New MPAPS format. 1.0 GENERAL: This standard conforms in all essentials with the SAE Standard for fuses, as defined below, which are intended to provide protection for automotive wiring and apparatus. 2.

5、0 RESTRICTED CHEMICAL SUBSTANCES: Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 DEFINITION: A fuse is a device designed to open the electrical circuit when subjected to overloads that c

6、ould damage the circuit or equipment. This is to be a non-reversible action and the fuse is intended to be replaced after the circuit malfunction has been corrected. 4.0 VOLTAGE RATING: Fuses will be rated at the voltage indicated in the dimensional table. 5.0 MAXIMUM VOLTAGE DROP: The maximum volta

7、ge drop (in millivolts) at rated current across the fuse only, will be as shown in Figure 1, when measured across the fuse from ferrule to ferrule. 6.0 AMPERE RATING: This standard covers ampere ratings up to and including 30 amperes. Preferred ampere ratings are shown in dimensional table. These ra

8、tings are determined at 75F (24C) ambient temperature. Approximate capacity change with respect to temperature is shown in Figure 2 for the recommended 1.250 in (31.75 mm) length fuses. The use of fuses in ambient temperature beyond the limits shown is not recommended without thorough testing experi

9、mentally in the vehicle. It is further recommended that fuses not be loaded to 100 percent of their adjusted capacity, according to ambient temperature, due to electrical system variation. See Figure 3 for additional deratings when fuses are used on cable gage sizes other than the test gage wire (SA

10、E #8). NUMBER: MPAPS S-R-5.101-GS TITLE: Fuses REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 2 of

11、3 7.0 IDENTIFICATION: The rated ampere capacity, type, and manufacturers identification symbol will be clearly and permanently marked on end of cap. Where so designated by part number, ampere rating will, in addition to marking on cap, be identified by a colored stripe around glass as specified in t

12、he dimensional table. Placement of the stripe on inside of glass will be preferable, however, where agreeable to purchaser, application of stripe to outside of glass will be permissible. Identification stripes will adhere to the glass, be uniform throughout and will not discolor, crack, fade or peel

13、 under normal storage, handling and operating conditions. 8.0 MATERIAL: Fuse tubes will be of clear glass. Fuse caps will be of brass or copper. Caps will be plated with nickel, cadmium, or other material having equivalent electrical and protective properties. 9.0 CONSTRUCTION: Fuse caps will be tig

14、htly attached to the glass tube, and the end will be square and free of solder. The fuse elements will be clearly visible through the glass tube. The fuses will be capable of being passed through a tubular gage having a length as long as the fuse and having a uniform hole of 0.258-0.259 in (6.55-6.5

15、9 mm) diameter. 10.0 PERFORMANCE TESTS: Fuses will perform satisfactorily when subjected to the overload, cycling and vibration tests specified below in accordance with the test procedure shown. 11.0 BEST PROCEDURE: The fuses, with the exceptions noted in the vibration test, will be mounted horizont

16、ally. When testing two or more fuses in series, the fuses will be mounted no less than 6 in (152 mm) apart with no less than 24 in (609 mm) of interconnecting cable. All electrical tests will be made using SAE #8 gage copper wire, and with fuse clip attachment terminals that have a maximum voltage d

17、rop of 4 millivolts per ampere when measured between points located on the wire 3 in (76 mm) from the attachment terminals. This determination will be made by using a solid copper dummy .250 in (6.35 mm) in diameter and 1.250 .005 in (31.75 0.13 mm) long, with suitable plated ferrules, installed in

18、the fuse clips. Test will be conducted within an ambient temperature range of 75 9F (24 5C), except for the overload test which is to be connected at 75 2F (24 1C). NUMBER: MPAPS S-R-5.101-GS TITLE: Fuses REVISION: 1506 This document is restricted and may not be sent outside Navistar, Inc. or reprod

19、uced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2015 by Navistar, Inc. JUNE 2015 Page 3 of 3 12.0 VIBRATION TEST: Fuses will perform satisfactorily after undergoing the following test. Suitably mounted specimens will be subjected to

20、a simple harmonic motion having an amplitude of .031 in (0.8 mm) travel.063 in (1.6 mm) maximum total excursion. The frequency will be varied uniformly between the limits of 10, and 55 HZ. The entire range of 10 to 55 HZ and return to HZ will be traversed in approximately 1 minute. This motion will

21、be applied for a period of 2 hours in each of the three mutually perpendicular directions (total of 6 hours). 13.0 OVERLOAD TEST: All types of fuses will carry 110 percent of the rated current continuously for 4 hours and will open at 135 percent in less than 1 hour. At 200 percent rated load, the f

22、use will open in less than 10 seconds. SFE fuses will be tested at 150 percent rated load and will open in 15 seconds maximum for ampere ratings of 20 and less or in 30 seconds maximum for SFE 30 amp fuses. 14.0 TECHNICAL INFORMATION: For further information related to the technical content of this

23、specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. 10400 W. North Avenue Melrose Park, IL 60160 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/