HOLDEN HN 1992-2010 WINDSCREEN WASHER FLUID《挡风玻璃喷洗器用液体》.pdf

《HOLDEN HN 1992-2010 WINDSCREEN WASHER FLUID《挡风玻璃喷洗器用液体》.pdf》由会员分享，可在线阅读，更多相关《HOLDEN HN 1992-2010 WINDSCREEN WASHER FLUID《挡风玻璃喷洗器用液体》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 1992 1 of 4 August, 1988 January, 2010 NAME: WINDSCREEN WASHER FLUID THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE T

2、O CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : S:EngBusProcessEngMaterialsMatlsAndAppearanceNBRspecific0AdminMgmtStandardFormsMatspec.doc 1. GENERAL This specification covers the requirements for use of windscreen washer fluid used for cleaning windscreens. This fluid must be compatible wi

3、th the exterior body paint finish, wiper paint finish and wiper blade rubber causing no detrimental defects. 2. TEST REQUIREMENTS For approval, the material shall be subjected to the following tests:- i) Compatibility With Exterior Body Paint Finish On test panels with exterior body topcoat, place 3

4、 drops each from a Pasteur pipette of the nominated fluid under test at the following concentrations: a) Suppliers recommended concentration. b) Twice the recommended concentration. c) As a concentrate. Allow the panels to sit overnight at room temperature then examine the painted finish. There shal

5、l be no detrimental defects observed such as film softening, permanent discoloration etc. NOTE: Allow the test panel 72 hours minimum ambient ageing after painting before testing to commence. ii) Compatibility With Wiper Blade Rubber In beakers containing the fluid under test at the following concen

6、trations: a) Suppliers recommended concentration. b) Twice the recommended concentration. c) As a concentrate. Fully immerse the wiper blade rubber material for 24 hours. There shall be no detrimental defects observed (immediately after immersion) on the wiper blade rubber material such as cracking

7、or material breakdown, etc. ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 1992 2 of 4 August, 1988 January, 2010 NAME: WINDSCREEN WASHER FLUID THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS TH

8、E RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : S:EngBusProcessEngMaterialsMatlsAndAppearanceNBRspecific0AdminMgmtStandardFormsMatspec.doc 2. TEST REQUIREMENTS (continued) iii) Compatibility With Wiper Paint Finish In beakers containing the fluid under test at th

9、e following concentrations: a) Suppliers recommended concentration. b) Twice the recommended concentration. c) As a concentrate. Half immerse the selected painted wiper part for 24 hours. Immediately after removal, no detrimental defects shall be observed such as film softening, blistering etc. iv)

10、Cleanability Cleanability of the fluid under test must be equivalent to or better than the approved control fluid. Refer to the appropriate Materials Engineer for cleaning evaluation. v) Fungal/Algae Growth In beakers containing the fluid under test, diluted with deionized water, at the following co

11、ncentrations: a) Suppliers recommended concentration. b) Twice the recommended concentration. c) Half the recommended concentration. Allow solutions to condition undisturbed in a controlled environment of 23 2 C and 55 5 % relative humidity for a period of 3 weeks. Upon visual examination on complet

12、ion of test, no growth of foreign bodies such fungal/algae material should be evident. ABN 84 006 893 232 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 1992 3 of 4 August, 1988 January, 2010 NAME: WINDSCREEN WASHER FLUID THIS DOCUMENT MUST NOT BE

13、REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID. FORM : S:EngBusProcessEngMaterialsMatlsAndAppearanceNBRspecific0AdminMgmtStandardFormsMatspec.doc 3. APPROVAL SUBMISSION Submission should include a test report de

14、tailing the requirements of Section 2 and a Materials Safety Data Sheet. After the time of approval, no change in formulation or process parameters shall be made without GM Holden Materials Engineering approval. 4. COLOUR Colour of concentrate shall be such that when diluted to the specified strengt

15、h the resulting solution can readily be seen through the reservoir. 5. APPROVAL, INSPECTION & REJECTION Refer HN 1000, Clauses A and C. 6. APPROVAL - (PRODUCTION TRY-OUT REQUIRED) Refer HN 1000 Clause G. 7. HAZARDOUS MATERIALS Refer HN 1000 Clause H. 8. RESTRICTED AND REPORTABLE SUBSTANCES (i) All s

16、ubstances and parts must meet the requirements of GMW3059. (ii) All chemical components present in materials supplied to this specification must comply with Australian NICNAS (National Industrial Chemicals Notification and Assessment Scheme) obligations. 9. REFERENCES GMW3059 HN1000 ABN 84 006 893 2

17、32 GM Holden Limited Engineering Department MATERIAL SPECIFICATION NUMBER SHEET RELEASE REVISION : HN 1992 4 of 4 August, 1988 January, 2010 NAME: WINDSCREEN WASHER FLUID THIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TO THE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRM THE DO

18、CUMENT ISSUE DATE IS STILL VALID. FORM : S:EngBusProcessEngMaterialsMatlsAndAppearanceNBRspecific0AdminMgmtStandardFormsMatspec.doc 10. APPROVED SUPPLIERS AND MATERIALS HN1992 is also known as part number 92139858. APPROVED SUPPLIER APPROVED MATERIAL Castrol Australia Pty. Limited Castrol Windscreen

19、 Washer Concentrate Shell Australia Ltd WWF HN1992 11. REVISIONS December, 1995 -Colour added December, 1996 - Blue colour requirement deleted, Approval (Production Try- out). - Hazardous Materials and Restricted Chemicals clauses added. January, 1997 - Clause 2 (v) Fungal/algae growth test added -

20、Approved source addedMay, 1997 - Approved source deletedMay, 2002 - Retitled and updated Section 9 to reflect new source and referenced specification to its eight digit part number. November, 2009 - Specification made Inactive. January, 2010 - HN1992 reactivated. - section “7.HAZARDOUS MATERIALS AND

21、 RESTRICTED CHEMICALS” - removed information about restricted chemicals -renamed this section “7.HAZARDOUS MATERIALS” - Added section “8.RESTRICTED AND REPORTABLE SUBSTANCES” - Added section “9.REFERENCES” - Re-numbered - section “9. APPROVED SUPPLIERS AND MATERIALS” to section 10 - section “8. REVISIONS” to section 11 Prepared by: Maria Lasic.